Planar Dome C3i/EX Bedienungsanleitung

Dome C3i/EX Display

User’s Guide

Solaris Systems

Information in this document has been carefully checked for accuracy; however, no

guarantee is given to the correctness of the contents. This document is subject to

change without notice. Planar provides this information as reference only. Reference

to other vendors’ product does not imply any recommendation or endorsement.

This document contains proprietary information protected by copyright. No part of

this manual may be reproduced by any mechanical, electronic, or other means, in

any form, without prior written permission of the manufacturer.

Planar, Dome, Dome C3i, Dome E2, Dome E3, Dome E3c, Dome E5, Dome DX2,

Dome CXtra, and RightLight are either registered trademark or trademarks of

Planar Systems, Inc. All other trademarks are the property of their respective owners.

020-0377-01A

iii

Contents

Product Information iv

About the Display 1

Installing the Display 5

Dome CXtra Software 26

Appendix 27

Index 43

Regulatory Compliance 45

Standard Warranty 51

iv | Dome Display

Product Information

The design of the Dome CX/Dome EX digital displays takes into

account every known measure to ensure your personal safety.

Improper use of the display can result in electric shock, fire, or

damage to the display. Read all instructions before setting up

the display.

Classification:

Shock Protection: Class I.

Degree of Protection Against Electric Shock: No applied part.

Degree of Protection Against Harmful Ingress of Water:

Ordinary equipment (IPX0).

Degree of Safety in the Presence of Flammable Anaesthetic

Mixture with Air or with Oxygen or Nitrous Oxide:

Not suitable for use in the presence of a flammable

anaesthetic mixture with air or with oxygen or nitrous oxide.

Mode of Operation: Continuous.

Important recycle instruction:

LCD lamp(s) inside this product contain mercury. This

product may contain other electronic waste that can be

hazardous if not disposed of properly. Recycle or dispose

in accordance with local, state, or federal laws. For more

information, contact the Electronic Industries Alliance at

WWW.EIAE.ORG. For lamp-specific disposal information, check

WWW.LAMPRECYCLE.ORG.

Product Information | v

Symbol explanations

Intended use

The Dome CX/Dome EX display is an AMLCD display designed for viewing

medical X-ray images. This unit should not be used near patients and should

be kept outside of 1.83 m perimeter and 2.29 m vertical.

IMPORTANT: Only the Dome E5 display can be used for primary

image diagnosis in mammography. The Dome C3i, Dome E2,

Dome E3, and Dome E3c display units must not be used for primary

image diagnosis in mammography.

CAUTION: Federal law restricts the Dome units to sale by or on

the order of a medical practitioner.

DISPOSAL. Do not use household or municipal waste

collection services for disposal of electrical and

electronic equipment. EU countries require the

use of separate recycling collection services.

CAUTION. Read the accompanying text carefully, for

proper operation and maintenance of the display

system.

DANGEROUS VOLTAGE. Important precautions about

electric shock. Read the accompanying text carefully,

to prevent damage to components of the display

system and for your safety.

DIRECT CURRENT.

BAROMETRIC PRESSURE. Transport and storage 12,000

meters (39,400 feet), maximum in unpressurized container.

RELATIVE HUMIDITY. Transport and storage 5% to 90%

(non-condensing).

TEMPERATURE. Transport and storage -10° to 60° C.

vi | Dome Display

Safety precautions

External equipment intended for connection to signal input, signal

output, or other connectors, must comply with the relevant IEC standard

(EN/IEC 60601-1 series for medical electrical equipment). In addition, all

such combinations (systems) must comply with the standard IEC 60601-1-1,

Safety requirements for medical electrical systems.

Equipment not complying to IEC 60601 must be kept outside the patient

environment, as defined in the standard as at least 1.5 meters from the

patient or the patient support.

Any person who connects external equipment to signal input, signal output,

or other connectors has formed a system and is therefore responsible for the

system to comply with the requirements of IEC 60601-1-1. If in doubt, speak

with a qualified technician.

GROUNDING RELIABILITY CAN ONLY BE ACHIEVED WHEN EQUIPMENT IS

CONNECTED TO AN EQUIVALENT RECEPTABLE MARKED “HOSPITAL ONLY” OR

“HOSPITAL GRADE.”

Safety tips

• Never open the display case, even when the power is off. Dangerous

voltage inside may cause electric shock or death.

• To avoid damage to the display, use the grounded power supply and

video cable supplied by Planar, or use certified replacements.

• Be sure the display is electrically grounded. You must connect the third

grounding pin on the US power cord to a grounded outlet. The European

power cord does not have a third grounding pin, but it must be plugged

into a grounded outlet.

• If you cannot insert the plug into the outlet you plan to use, have a

licensed electrician replace the outlet with a properly grounded outlet.

If the power cord connects directly into the computer, make sure the

computer is grounded.

• Keep the display dry if it is part of a surgical system. The display lacks

protection against liquids or spills.

• In locations where 240V outlets are used, connect the Dome display

only to a center-tapped, 240V, single-phase supply (only for Canada

and the United States).

Product Information | vii

Unpacking and handling tips

The Dome display is a precision instrument that requires proper care to

maintain product operation and adherence to specification. Unpack the

display and components carefully, then set up and handle the unit properly

to avoid damage to the LCD panel.

• Use both hands to grasp the display case when lifting it from the shipping

carton, but avoid touching the screen.

• Do not apply pressure to the screen or touch the screen with bare fingers

or objects. Pressure can affect image quality. Cosmetics and oils on the skin

are both detrimental to the screen and difficult to remove.

• Allow the display to warm up to room temperature before turning it on.

Avoid sudden temperature changes in the environment, as this may cause

condensation, which damages the display.

• Secure the display properly onto a standard VESA 100-mm mounting unit if

you elect not to use the desk stand.

• Do not set up the display near strong light or heat sources.

• Do not block the vents on the back of the display or install the display in

a built-in enclosure. Blocked vents cause excessive heat to build up inside

the display, increasing risk of fire.

• When installing components, turn off your computer, but leave it plugged

into a grounded outlet.

• Do not remove the back cover or disassemble the display. There are

no user-serviceable parts inside.

Preventing fire and injury

• Replace the power supply or cables if damaged.

• Use only the power source indicated in this guide or listed on the display.

• Do not plug the power supply into an overloaded AC outlet or extension

cord. Overloaded AC outlets and cords can result in electric shock or fire.

• Do not drop or push objects into the display case. Internal components

contain high voltage.

• Unplug the power cord from the wall outlet during thunderstorms.

• Do not place magnetic devices, such as motors, near the display.

viii | Dome Display

Cleaning the display

Observe the following guidelines to maintain the display and the LCD screen.

• Use a clean, lint-free, absorbent cotton cloth to clear off any residual glue

from removal of the protective film or to remove surface dust. Apply light

pressure to remove the dust.

• Dampen a clean cloth with a small amount of isopropyl alcohol to remove

glue or dust if the screen is still not clean. Do not saturate the cloth;

otherwise, alcohol may seep into the display case and collect in the

enclosure. Use a clean, dry cloth to completely remove the alcohol residue.

• Do not use chemically treated dust cloths, acetone, toluene, or harsh

solvents on the display case or the screen. They can damage the polarizer

and the display case.

• Do not expose the display to water or excessive moisture. Do not allow

water or other stains to stand on the unit. Wipe liquids off immediately to

prevent damage to the display case and the screen.

WARNING

DISCONNECT SUPPLY BEFORE SERVICING

AVERTISSEMENT

COUPER L’ALIMENTATION AVANT L’ENTRETIEN ET LE DEPANNAGE

Product Information | ix

Shipping/storing the display

Keep the display in its shipping container until installation. Return the display

to its original container whenever you need to store the unit, move it to

another location, or return it for repair. The packaging supplied by the

manufacturer protects the display while it is in transit. See environment

specifications for more information.

Before returning the display to the container, do the following:

1 Swivel the display panel in portrait mode.

2 Push the panel down to the lowest position.

3 Use the stand lock to anchor the panel.

Disposal information

Follow your local governing ordinance and recycling policy for

proper disposal or recycling of display components.

AMLCD panel mounted on desk stand

Display controller DC power adapter Power cords

DVI cable Quick reference

Display driver and

Dome CXtra software

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planar Monitor Handbücher

Planar

Planar LA1500R Bedienungsanleitung

Planar

Planar VS15XAD Bedienungsanleitung

Planar

Planar PX23MW Bedienungsanleitung

Planar

Planar PLL1911M Bedienungsanleitung

Planar

Planar Helium PCT2485 Bedienungsanleitung

Planar

Planar PX2211MW Bedienungsanleitung

Planar

Planar ICEBrite EL480.240-PR2 Bedienungsanleitung

Planar

Planar LB1500R Bedienungsanleitung

Planar

Planar PT1745P Bedienungsanleitung

Planar

Planar Dome E2c Bedienungsanleitung

Planar

Planar ICEBrite EL480.240-PR2 Bedienungsanleitung

Planar

Planar PX2210MW Bedienungsanleitung

Planar

Planar UltraRes W Series Bedienungsanleitung

Planar

Planar IX2851 Bedienungsanleitung

Planar

Planar LED2210MW Bedienungsanleitung

Planar

Planar CleanPole M4POLE-PS Bedienungsanleitung

Planar

Planar PXL2760MW Bedienungsanleitung

Planar

Planar Dome C2 Bedienungsanleitung

Planar

Planar PL2210W Bedienungsanleitung

Planar

Planar HB Series Bedienungsanleitung

Planar

Planar PXN2490MW Bedienungsanleitung

Planar

Planar PX171M Bedienungsanleitung

Planar

Planar UltraRes 4K Bedienungsanleitung

Planar

Planar PT191MU Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung