Planar PDP42HD Bedienungsanleitung
Planar Plasma 1
Important Information
Warning: To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
Caution: To reduce the risk of electric shock, do not remove cover (or back).
No user-serviceable parts inside. Refer servicing to qualified service
Personnel.
Note to CATV system installer: This reminder is provided to call CATV system Installer’s
attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical
Code, Part 1), that provides guidelines for proper grounding and, In particular, specifies that
the cable ground shall be connected to the grounding system of the building as close as to
the point of cable entry as practical.
Caution: FCC/ CSA regulations state that any unauthorized changes or modifications to this
equipment may void the user's authority to operate it.
Important: One Federal Court has held that unauthorized recording of copyrighted TV
programs is an infringement of U.S. copyright laws. Certain Canadian programs may also be
copyrighted and any unauthorized recording in whole or in part may be in violation of these
rights.
FCC Information
The FCC Radio Interface Statement includes the following warning:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. When such interference to radio or television reception occurs, the user
will be required to correct the interference at own expense. The interference may be
correctly using one or more of the following measures:
-Increase the separation between the equipment and receiver.
-Reorient or relocate the receiving antenna.
-Connect the equipment into an different outlet from the receiver.
FCC Warning
To maintain FCC compliance for the product the user must use shielded signal interface
cables and UL approved
CAUTION
Risk of electric
shock. Do not open.
2 Planar Plasma
Safety Precautions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an eletrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table sprecified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have gallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
15. Apparatus shall not be exposed to dripping or splashing and no objects fill with liquids,
such as vases, shall be placed on the apparatus.
Planar Plasma 3
Table of Contents
Product Features………………………………………………………..……………………5
Package Content……………………………………………………………………………..6
Standard Accessories……………………………………………………………….6
Optional Accessories………………………………………………………………..7
Plasma Display………………………………………………………………………………..8
Front Panel…………………………………………………………………………….8
Rear Panel……………………………….…………………………………………….9
Setting Up the Plasma…………………………………………………………………….10
Getting Started………………………………………………………………………10
Video/Audio Connection………………………………………………………….11
External Speaker…………………………………………………………………….12
Other Connections………………………………………………………………….13
Front Panel Controls……………………………………………………………….14
Remote Control………………………………………………………………………………15
Overview……………………………………………………………………………….15
Inserting Batteries………………………………………………………………….16
Precaution……………………………………………………………………………..16
Using the Remote Control……………………………………………………….17
OSD Functions……………………………………………………………………………….19
OSD Menu Overview………………………………………………………………19
OSD Menu Operation……………………………………………………………..20
Parental Control…………………………………………………………………………….25
V-Chip Setup…………………………………………………………………………25
Change Password………………………………………………………………….28
Close Caption………………………………………………………………………………..29
Using Close Caption……………………………………………………………….29
Specification………………………………………………………………………………….30
Factory Setting………………………………………………………………………………31
Troubleshooting…………………………………………………………………………….32
Care and Maintenance……………………………………………………………………35
4 Planar Plasma
Product Features
42 inch Plasma Display: With 720p native resolution (1024 x 768).
D-Sub 15 VGA Input: Allow user to connect computer to the plasma and use the
plasma as computer monitor.
Input Signals
Component Video (YCbCr/ YPbPr)
Composite Video
S-Video
RGB (D-Sub 15pin)
Digital DVI
RS232 Communication Port (D-Sub 9pin)
TV Tuner Built-in
16:9 Enhancement: Widescreen technology that maximizes picture quality when
playing widescreen enhanced video.
Channel Memory: Allow user to add and remove channel according to the personal
preference.
Picture in Picture: User may simultaneously watch two images from different video
sources
Parental Control: V-Chip technology allows parents to block unsuitable programming
for under age viewers.
Digital Visual Interface (DVI): To accommodate a DVI-D interfaces.
3-D Digital Comb Filter: Enhances color purity of Composite Video and S-video input
sources, reducing cross-color artifacts like dot crawl and moiré.
Color Temperature: With 3 options of user selectable color temperature allowing user
to optimize the image.
TV Tuner Built-in: Built-in NTSC tuner to receive conventional analog broadcasts;
de-interlacing circuit with 3:2 pull down converts interlaced analog sources to
progressive-scan display, significantly improving picture quality
Wide Viewing Angle: Over 160 degrees (horizontal and vertical) viewing angle.
Built-in TV and TV Audio Out: Outputs TV video/audio signal to other device.
Built-in Speakers: Stereo speakers built-in with 2 watts per channel.
Built-in Screen Move: Screen move feature to decease chances of screen burn.
(1) an optional set-top HDTV receiver box is required to receive digital signals
Package Content
Planar Plasma 5
Standard Accessories
Plasma Stand Video/Audio Cables
Remote Control /AAA Battery S-Video cable
User Manual D-Sub 15 Video Cable
Power Cable
Optional Accessories
6 Planar Plasma
Speakers Speaker Stand
Wallmount
Planar Plasma 7
Plasma Display
Front Panel
Indicator Light Remote Control
Sensor
Infrared Receiver: Receives infrared signals from the remote control. Aim the remote
control within 30 degree left and right.
Indicator Light: This LED light is to indicate the main power status.
Indicator (Amber): Standby mode
Indicator (Blue): Power ON mode
Desktop Stand: Desktop stand comes as standard accessory. Allowing user to set the
plasma on the table.
8 Planar Plasma
Rear Panel
Video Connection Interface: Video connection includes Component Video,
Composite Video, S-video, DVI, D-Sub 15, TV Tuner, and Video/Audio Out.
Main Power Switch: Master power switch to switch the plasma between Power Off
mode and Standby mode.
Power Input Jack: Power source for the plasma.
External Speaker Line Out: Allow user to connect external speakers to the plasma.
Video/Audio Connection
Interface
Power Input Jack
External Speaker
Line Out
Main Power Switch
Planar Plasma 9
Setting Up the Plasma
Getting Started
Power Input Jack: Auto switch power supply accepts input of 110 V~240 V. Use only
UL approved power cord with proper grounding.
Main Power Switch: Turn the switch to on position before initial use of the plasma
unit. “-” Indicate on and “Ο” indicate off. When the switch is on the LED will turn to
amber color.
Andere Handbücher für PDP42HD
1
Inhaltsverzeichnis
Andere Planar Monitor Handbücher
Planar
Planar PT1704N Bedienungsanleitung
Planar
Planar UltraRes Bedienungsanleitung
Planar
Planar Dome Q2 Bedienungs- und Wartungshandbuch
Planar
Planar PX2210MV Bedienungsanleitung
Planar
Planar PL1702 Bedienungsanleitung
Planar
Planar PJT155R Bedienungsanleitung
Planar
Planar VitalScreen S VSS15X Bedienungsanleitung
Planar
Planar PT1545R Bedienungsanleitung
Planar
Planar UltraRes W Series Bedienungsanleitung
Planar
Planar Dome E2 Bedienungsanleitung
Planar
Planar LC12 Bedienungsanleitung
Planar
Planar PQ1710M Bedienungsanleitung
Planar
Planar Helium PCT2785 Bedienungsanleitung
Planar
Planar LC1200R Bedienungsanleitung
Planar
Planar PL1910W Bedienungsanleitung
Planar
Planar PT1700M(U) Bedienungsanleitung
Planar
Planar 81000ALBI Bedienungsanleitung
Planar
Planar LT3200 Bedienungsanleitung
Planar
Planar PE2010 Bedienungsanleitung
Planar
Planar SD2420W Bedienungsanleitung
