PLANET ECLIPSE CS3 Bedienungsanleitung

CS3

SUB TITLE

PLANET ECLIPSE: CS3

USER MANUAL: ENGLISH ECLIPSE®ADVANCED

PAINTBALL TECHNOLOGY

A I R 6 8 C A L

CS3

!WARNING!

IMPORTANT SAFETY NOTICES

!PLANET ECLIPSE PAINTBALL EQUIPMENT IS NOT A TOY.

PAINTBALL SAFETY RULES MUST BE FOLLOWED AT ALL

TIMES.

!Care ess or improper use of the marker and/or parts,

inc uding fai ure to fo ow instructions and warnings within

this user manua cou d cause serious injury or even death.

!Do not remove or deface any warnings attached to the

marker.

!Paintba industry standard eye/face/ear and head

protection designed specifica y to stop paintba s and

meeting ASTM standard F1776 (USA) or CE standard (Europe)

must be worn by the user and any person within range.

Proper protection must be worn during assemb y, c eaning

and maintenance.

!Hearing protection shou d be worn.

!Never shoot towards a person who is not wearing proper

protection.

!Never ook direct y into the barre of the marker. Accidenta

discharge into the eyes may cause permanent injury or even

death. Never ook into the barre or breech area of the

marker whi st the marker is switched on and ab e to fire.

!Keep the marker switched off unti ready to shoot.

!Treat every marker as if it is oaded and ready to fire.

!The e ectronic ON/OFF button is the marker’s disab ing

device. A ways switch OFF when not in use.

!A ways fit a barre -b ocking device when not in use.

!A ways remove paintba s from the marker when not in use.

!Do not fie d strip or remove any parts whi e the marker is

pressurised.

!Do not pressurise the marker without the components of the

marker correct y insta ed; high-pressure gas may be emitted.

!Do not fire the marker without the bo t correct y insta ed.

!Never put your finger or any foreign objects into the paintba

feed tube of the marker.

!Never a ow pressurised gas to come into contact with any

part of your body.

!A ways remove the first stage regu ator and re ieve a

residua gas pressure from the marker before disassemb y.

!A ways remove the first stage regu ator and re ieve a

residua gas pressure from the marker for transport and

storage.

!A ways fo ow guide ines given with your first stage regu ator

for safe transportation and storage.

!A ways store the marker in a secure p ace.

!Observe a oca and nationa aws, regu ations and

guide ines.

!Persons under 18 years of age must have adu t supervision

when using or hand ing the marker.

CS3

WARNING!

IMPORTANT SAFETY NOTICES

!On y use professiona paintba fie ds where codes of safety

are strict y enforced.

!Use compressed air/nitrogen on y. Do not use any other

compressed gas or pressurised iquid inc uding CO2.

!A ways fo ow instructions, warnings and guide ines given with

any first stage regu ator you use with the marker.

!Use 0.68 inch ca ibre paintba s on y.

!A ways measure your marker’s ve ocity before p aying

paintba , using a suitab e chronograph.

!Never shoot at ve ocities in excess of 300 feet (91.44 metres)

per second, or at ve ocities greater than oca or nationa aws

a ow.

!Any insta ations, modifications or repairs shou d be carried

out by a qua ified individua at a icensed and insured

paintba faci ity.

THIS USER MANUAL IS IN ENGLISH.

It contains important safety guide ines and

instructions. Shou d you be unsure at any stage,

or unab e to understand the contents of this

manua you must seek expert advice.

LE MODE D’EMPLOI EST EN ANGLAIS.

I contient des instructions et mesures de

sécurité importantes. En cas de doute, ou s’i

vous est impossib e de comprendre e contenu

du monde d’emp oi, demandez consei à un

expert.

ESTE MANUAL DE USUARIOS (OPERARIOS)

Usarios está en Ing és.Contiene importantes

normas de seguridad e instrucciones. Si no está

seguro de a gùn punto o no entiende os

contenidos de este manua debe consu tar con

un experto.

DIESE BEDIENUNGS - UND

BENUTZERANLEITUNG IST IN ENGLISCH.

Sie enthae t wichtige Sicherheitsricht inen und -

bestimmungen. So ten Sie sich in irgendeiner

Weise unsicher sein, oder den Inha te dies

Heftes nicht verstehen, assen Sie sich bitte von

einen Experten beraten.

WARNING !

This user manua must accompany the product in the event of resa e or new

ownership. Shou d you be unsure at any stage you must seek expert advice.

CS3

04 CONTENTS

LET’S GO

02 Important Safety Notices

04 Let’s Go

0 Welcome to Planet Eclipse

06 Setting up

08 Switching the Marker On/Off

09 User Interface

10 Oled Indicators

14 Firmware Version Check

1 BS Status Indicator

16 Removing the Grips

17 Replacing the Grips

18 Battery Replacement

19 Tournament Lock Button

20 Breech Sensors and Detents

21 Velocity Adjustment

22 Trigger Adjustment

23 Factory Restore

24 Unloading the Marker

26 Storage and Transportation

27 We Got Your Back

28 Fault Finding Tables

32 Servicing Intervals

33 Tech Resources

3 Oled Run Screens

36 User Interface

37 Navigating the User Interface

38 Presets

39 Factory Presets

40 User Interface Parameters

4 Settings Menu Summary

9 Regulatory Approval RN4871

60 E-Portal (Version 4.5 or Later)

61 E-Portal Lite

62 Bolt Assembly

64 Parts List

66 Index

CS3

WELCOME

TO PLANET ECLIPSE

SUPPORT

Ec ipse customers have access to our wor dwide

technica support network that wi he p you with

any technica prob ems from oca ised service

centres to on-site* tech support.

WARRANTY

Our exceptiona 24 months from date of

manufacture OR minimum of 12 months with

proof of purchase warranty ensures your c aim

wi be repaired or rep aced in a snap!

QUALITY

A Ec ipse products undergo meticu ous checks

by experienced specia ists who care about the

product that arrives at your door. Precision

materia s + high standards = a qua ity product.

STANDARD

Your Ec ipse marker is awesome and requires no

after market parts however, for genuine Ec ipse

accessories and support p ease consu t your

oca Ec ipse Dea er for upgrade options.

* Conditions app y, see on ine po icies for fu

detai s at p anetec ipse.com

CS3

06 INTRODUCTION

SETTING UP

C B D

F E

FIG.1

CS3

INTRODUCTION

SETTING UP

FIG.1

ASWITCH MARKER OFF BEFORE YOU BEGIN.

BBUILD THE 3-PIECE S63 BARREL.

S ide the insert into the back section.

Rotate the barre tip counter-c ockwise onto the back.

CATTACH THE COMPLETE BARREL TO THE MARKER.

Rotate the barre c ockwise into the marker body.

DFIT A BARREL BLOCKING DEVICE FOR SAFETY.

EENSURE THE MARKER IS DE-GASSED.

Push and ho d the POPS button then s ide the POPS bonnet

away from the POPS body.

FATTACH A PRE-SET AIR SYSTEM.

Rotate the air system c ockwise into the POPS body.

GLOOSEN THE CLAMPING FEEDNECK.

Open the feedneck ever away from the feedneck.

Rotate the feed whee counter-c ockwise.

HATTACH A LOADER.

ISECURE THE LOADER.

Rotate the feed whee c ockwise to tighten.

C ose the feedneck ever to secure.

JGAS THE MARKER.

Push the POPS bonnet into the POPS body unti it engages.

KSWITCH ON THE MARKER.

!IMPORTANT! To switch ON/OFF see page 08.

!DO NOT over-tighten the barre .

!ALWAYS ensure marker is de-gassed when setting up.

!NEVER use CO2. On y use compressed air or Nitrogen.

WARNING !

A ways make sure that the marker is OFF with a barre b ocking device insta ed and

that no paintba s are in the marker or oader before attaching an air system.

Compressed air and nitrogen systems can be extreme y dangerous if hand ed or

used incorrect y.

On y attach an air system certified for use within the country of use.

Never add ubricants or grease into the fi adaptor of the air system regu ator.

Ensure that a screws are tightened and no parts are oose before insta ing an air

system.

Do not pressurise the marker without the bo t system correct y insta ed, as high

pressure gas wi be emitted.

Do not insta a compressed air system or oad paintba s into the marker unti you

fee confident with your abi ity to hand e the marker safe y and responsib y.

CS3

08 INTRODUCTION

SUB TITLE

CS3

08 INTRODUCTION

SWITCHING THE MARKER ON/OFF

FIG.1

The navigation conso e houses the breech sensor (BS) status

indicator A; the navigation buttons: Up BSelect CDown D;and the

OLED screen E.

SWITCHING ON

Press and ho d Select ( or doub e-c ick it * ) unti the marker powers

up. The LED Awi f ash to indicate the BS status.

See page 15 for BS status indicator references.

SWITCHING OFF

Press and ho d Select unti TURN OFF? is disp ayed. Press Select

again to switch off.

FIRING THE MARKER

Pu the trigger to fire. The BS status indicator (LED) and the breech

sensor indicator (OLED) wi indicate if the marker is ab e to fire.

To togg e the breech sensor on/off push and ho d Up for 0.5 seconds

when the marker is on. See page 10 for BS indicator states.

* Doub e-c ick can be disab ed in the HARDWARE menu (page 48).

WARNING!

DO NOT dry fire your marker as this may ead to damage over a sustained period.

FIG.1

CS3

INTRODUCTION

USER INTERFACE

CS3

FIG.1

Once powered-up a run screen wi be disp ayed. There are a number

of run screens and, with the exception of the Sp ash screen, they a

have the same ayout.

ATap Up to cyc e through the run screens.

BRun screen specific information.

CThe breech sensor (BS) indicator.

See page 10 for BS indicator states.

DThe service indicator.

EFactory preset indicator.

FThe trigger detection indicator.

GThe sound indicator.

HThe B uetooth®indicator.

IThe tournament ock indicator (to togg e the tournament

ock see page 19).

JThe battery eve indicator (see page 13).

FIG.1

CS3

10 INTRODUCTION

OLED INDICATORS

FIG.1

The BS indicator Adisp ays the various states of the breech sensor.

BS ENABLED AND A BALL IS DETECTED

The marker can be fired up to the se ected rate of fire.

BS ENABLED AND NO BALL IS DETECTED

The marker cannot be fired.

BS DISABLED

The marker can be fired up to the rate of fire set by the BS

OFF ROF parameter (see page 40).

BS ENABLED IN TRAINING MODE

Training mode is enab ed and simu ates firing up to the

se ected rate of fire.

BS DISABLED IN TRAINING MODE

Training mode is enab ed and simu ates firing up to the rate

of fire set by the BS OFF ROF parameter.

BS DISABLED DUE TO DETECTION FAULT

A fau t has temporari y disab ed the BS and reduced the rate

of fire to 2bps be ow the BS ON ROF parameter.

BS FAULT CLEARED AND A BALL IS DETECTED

A fau t has been c eared and the marker can be fired up to

the se ected rate of fire.

BS FAULT CLEARED AND NO BALL IS DETECTED

A fau t has been c eared but the marker cannot be fired.

Andere PLANET ECLIPSE Paintball-Ausrüstung Handbücher

PLANET ECLIPSE

PLANET ECLIPSE EMF100 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE LV1.6 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE ETHA2 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE GEO2 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE emek fl 3-way valve Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE Etek STAR Frame Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE CS3 .68CAL Gebrauchsanweisung

PLANET ECLIPSE

PLANET ECLIPSE GTEK170R Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE Eclipseblade E2 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE SL Series Betriebsanleitung

PLANET ECLIPSE

PLANET ECLIPSE EGO LV1 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE 180R.68CAL Gebrauchsanweisung

PLANET ECLIPSE

PLANET ECLIPSE GEO IV CORE Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE GTEK M170R Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE GSL Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE EGO TEN Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE GEO CS1 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE GEO 4 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE EGO LV2 Gebrauchsanweisung

PLANET ECLIPSE

PLANET ECLIPSE ETHA3 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE MG 100 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE GMEK Bedienungsanleitung

Beliebte Paintball-Ausrüstung Handbücher anderer Marken

First Endeavor Paintball

First Endeavor Paintball The Quest Bedienungsanleitung

PMI

PMI Piranha VTL Bedienungsanleitung

Proto

Proto SLG ULTRALITE Bedienungsanleitung

Bob Long Technologies

Bob Long Technologies Alias Intimidator Bedienungsanleitung

Proto

Proto REFLEX RAIL Bedienungsanleitung

MCS

MCS BOX DRIVE Bedienungsanleitung

Spyder

Spyder MR1 Bedienungsanleitung

Evil

Evil OMEN 2.0 Bedienungsanleitung

GOG

GOG Envy Leitfaden

Evil

Evil Pimp Kit Bedienungsanleitung

Proto

Proto SWITCH EL Bedienungsanleitung

Empire

Empire MINI Bedienungsanleitung

Psychoballistics

Psychoballistics SILVER BULLET LCD Bedienungsanleitung

Virtue

Virtue SPIRE III Bedienungsanleitung

Dangerous power

Dangerous power G3 SPEC-R Bedienungsanleitung

Valken

Valken Code Bedienungsanleitung

Indian Creek Design

Indian Creek Design BushMaster Series Bedienungsanleitung

PMI

PMI BlackMaxx Bedienungsanleitung