Planet IPOE-E202 Bedienungsanleitung

Industrial 1-port 802.3at PoE+ to 2-port 802.3af

PoE Extender

IPOE-E202

User’s Manual

Trademarks

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other

trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work

properly in all environments and applications, and makes no warranty

and representation, either implied or expressed, with respect to

the quality, performance, merchantability, or tness for a particular

purpose.

PLANET has made every effort to ensure that this User’s Manual is

accurate; PLANET disclaims liability for any inaccuracies or omissions

that may have occurred.

Information in this User’s Manual is subject to change without notice

and does not represent a commitment on the part of PLANET. PLANET

assumes no responsibility for any inaccuracies that may be contained in

this User’s Manual. PLANET makes no commitment to update or keep

current the information in this User’s Manual, and reserves the right

to make improvements to this User’s Manual and/or to the products

described in this User’s Manual, at any time without notice.

If you nd information in this manual that is incorrect, misleading, or

incomplete, we would appreciate your comments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the Instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may

cause radio interference, in which case the user may be required to

take adequate measures.

WEEE Warning

To avoid the potential effects on the environment and human

health as a result of the presence of hazardous substances in

electrical and electronic equipment, end users of electrical

and electronic equipment should understand the meaning of

the crossed-out wheeled bin symbol. Do not dispose of WEEE as

unsorted municipal waste and have to collect such WEEE separately.

Revision

PLANET Industrial 1-Port 802.3at PoE+ to 2-Port 802.3af PoE Extender

User’s Manual

FOR MODEL: IPOE-E202

REVISION: 2.0 (JULY, 2017)

Part No: EM-IPOE-E202_v2.0 (2350-AF0500-002)

Table of Contents

1. Introduction.............................................................................. 5

1.1 Package Contents ............................................................... 5

1.2 How to Use This Manual...................................................... 5

1.3 Product Features................................................................. 5

1.4 Product Specications ......................................................... 8

1.5 Power over Ethernet Budget ...............................................10

1.6 Power over Ethernet Capability ...........................................10

1.6.1 When PSE/PoE Switch Output is DC 52V ....................10

1.6.2 When PSE/PoE Switch Output is DC 56V ....................11

2. Installation ..............................................................................12

2.1 Physical Dimensions ...........................................................12

2.2 Front Panel .......................................................................13

2.3 Rear Panel ........................................................................14

2.4 Mounting Installation..........................................................14

2.4.1 Making Waterproof RJ45 Cable ..................................15

2.4.2 Wall Mounting ..........................................................16

2.4.3 Connecting waterproof RJ45 connector

to the IPOE-E202 .....................................................17

2.5 Connecting IPOE-E202 to Power Source Equipment (PSE) .....19

2.6 Connecting IPOE-E202 to Powered Device (PD) ....................20

3. Customer Support ....................................................................22

APPENDIX A: Networking Connection...............................................23

A.1 Switch’s RJ45 Pin Assignments ............................................23

A.2 RJ45 Cable Pin Assignments................................................24

1. Introduction

1.1 Package Contents

Check your package for the following parts:

Industrial PoE Extender x 1

User’s Manual x 1

Waterproof RJ45 Connector x 3

Wall-mounted Kit x 1

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing

material, and use them again to repack the product in case there is a

need to return it to us for repair.

1.2 How to Use This Manual

This Industrial PoE Extender User Manual is structured as

follows:

Chapter 2 Installation

The chapter explains the feature, functionality and the physical

installation of the Industrial PoE Extender.

Chapter 3 Customer Support

The chapter explains how to get support from PLANET.

Appendix A

This chapter contains cable information of the Industrial PoE Extender.

1.3 Product Features

Physical Port

3-port 10/100/1000BASE-T Gigabit RJ45 interface

1-port data + power input

2-port data + power output

Power over Ethernet

1-port data + power input

Complies with IEEE 802.3at Power over Ethernet Plus end-

span/mid-span PD

Supports PoE input power up to 30.8 watts

2-port data + power output

Complies with IEEE 802.3af/IEEE 802.3at Power over Ethernet/

end-span PSE

Up to 2 IEEE 802.3af/802.3at devices powered

Supports PoE power up to 25 watts for each PoE port

Auto detects powered device (PD)

Extends the range of PoE to an additional 100 meters (328ft.)

Forwards both Ethernet data and PoE power to remote device

Layer 2 Features

Hardware based 10/100Mbps, half/full duplex and 1000Mbps full

duplex mode, ow control, auto-negotiation and auto MDI/MDI-X

Features Store-and-Forward mode with wire-speed ltering and

forwarding rates

IEEE 802.3x ow control for full duplex operation and back pres-

sure for half duplex operation

Integrates address look-up engine, supporting 2K absolute MAC

addresses

9K jumbo frame support in 1000Mbps duplex mode

Automatic address learning and address aging

Supports CSMA/CD protocol

Industrial Case and Installation

IP63 aluminum case

Wall-mount design

Waterproof and dustproof

Supports EFT protection of 2000 VDC for power line

Supports 2000 VDC Ethernet ESD protection

-40 to 75 degrees C operating temperature

No external power cable required for installation

Plug and Play installation

Standard Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab 1000BASE-T

IEEE 802.3x Flow Control

IEEE 802.3at Power over Ethernet Plus

IEEE 802.3af Power over Ethernet

FCC Part 15 Class A, CE

Note

PSE (Power Sourcing Equipment) is a device (switch

or hub for instance) that provides power in a PoE setup.

Maximum allowed continuous output power per such

device in IEEE 802.3af is 15.4W, and in IEEE 802.3at is

30W.

PDs (Powered Devices) like PoE IP phones, PoE IP

cameras, PoE wireless access points, etc. are PoE-enabled

terminals that consume energy via PSE.

1.4 ProductSpecications

Model IPOE-E202

Hardware Specications

Hardware Version 2

Network Connector

PoE In Port

1 x 10/100/1000BASE-T Ethernet with High

PoE “Data + Power” in, auto MDI/MDI-X,

auto-negotiation RJ45 connector

PoE Out Port

2 x 10/100/1000BASE-T Ethernet with IEEE

802.3af/at PoE “Data + Power” out, auto

MDI/MDI-X, auto-negotiation RJ45 connector

Switch Architecture Store-and-Forward switch architecture

MAC Address Table 2K MAC address table with auto learning

function

Data Buffer 1Mbit

Switch Fabric 6Gbps

Switch Throughput 4.46Mpps @ 64 bytes

Flow Control IEEE 802.3x pause frame for full duplex

Back pressure for half duplex

Jumbo Frame 9KB

ESD Protection 2KV DC

EFT Protection 2KV DC

Enclosure IP63 aluminum case

Installation Wall-mount kit

LED Display

System: PWR (Green)

PoE Input Port: LNK/ACT (Orange)

PoE Input Port: 1000 (Orange)

Budget Alert (Green)

Per PoE Output Port: LNK/ACT (Green)

Per PoE Output Port: PoE-in-Use (Orange)

Cable

Twisted-pair cable:

10BASE-T: 2-pair UTP Cat. 3, 4, 5 up to 100

meters

100BASE-TX: 2-pair UTP Cat. 5, 5e up to 100

meters

1000BASE-T: 4-pair UTP Cat. 5e, 6 up to 100

meters

Dimensions (W x D x H) 199.6 x 81 x 40 mm

Weight 373g

Power Consumption 30 watts/102.3BTU (Full loading with PoE

function)

Power over Ethernet

PoE Standard

PoE In Port

IEEE 802.3at Power over Ethernet Plus

end-span/mid-span PD class 4 PD

Per PoE Out Port

IEEE 802.3at Power over Ethernet Plus

end-span PSE

IEEE 802.3af Power over Ethernet end-span

PSE

PoE Power

PoE In Port

50~57V DC, max. 30.8 watts

Per PoE Out Port

44~55V DC, max. 25 watts

Power Pin Assignment

PoE In Port

1/2(+), 3/6(-); 4/5(+), 7/8(-)

Per PoE Out Port

1/2(-), 3/6(+)

Standards Conformance

Regulatory Compliance FCC Part 15 Class A, CE

Stability Testing

IEC 60068-2-32 (Free fall)

IEC 60068-2-27 (Shock)

IEC 60068-2-6 (Vibration)

Standards Compliance

IEEE 802.3 Ethernet

IEEE 802.3u Fast Ethernet

IEEE 802.3ab Gigabit Ethernet

IEEE 802.3x Flow Control

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

Environment

Operating Temperature: -40 ~ 75 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

Storage Temperature: -40 ~ 85 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

1.5 Power over Ethernet Budget

The following table lists how many PoE devices can be powered by

IPOE-E202:

Power Source PoE Output

Budget*

Max. Number of PDs

supported

IEEE 802.3at PoE+

PSE 25 watts max.

Class 4 PD@25

watts 1 unit

Class 3 PD@15

watts 2 units

Class 2 PD@7 watts 2 units

IEEE 802.3af PoE PSE 10 watts max. Class 2 PD@7 watts 1 unit

Remarks

The PoE output budget means the 2-port PD aggre-

gated power output. The aggregated power consump-

tion will be below 30 watts if with PoE+ PSE.

1.6 Power over Ethernet Capability

With different distance and different PoE input source, it will inect the

PoE output capability. Please refer to the table below.

PSE/PoE Switch

PoE Output Capacity

IPOE-E202

(A) (B) (C)

(A): Distance

(B): Distance

(A): Watts

1.6.1 When PSE/PoE Switch Output is DC 52V

A (Distance) B (Distance) C (Watts)

2M 2M 26

2M 20M 25.5

2M 60M 19.6

2M 100M 14.6

Inhaltsverzeichnis

Andere Planet Extender Handbücher

Planet

Planet PL-510W Bedienungsanleitung

Planet

Planet VC-203PT Bedienungsanleitung

Planet

Planet POE-E304 Bedienungsanleitung

Planet

Planet IPOE-E302 Bedienungsanleitung

Planet

Planet LRE-101 Bedienungsanleitung

Planet

Planet LRP-101C-KIT Bedienungsanleitung

Planet

Planet WNAP-1110 Bedienerhandbuch

Planet

Planet LRE-101C Bedienungsanleitung

Planet

Planet WAP-7500 Bedienerhandbuch

Planet

Planet IVC-234GT Bedienungsanleitung

Planet

Planet WRE-1200 Bedienungsanleitung

Planet

Planet POE-E201 Bedienungsanleitung

Planet

Planet WNAP-C3220 Bedienungsanleitung

Planet

Planet IVC-4011-T-V2 Bedienungsanleitung

Planet

Planet IPOE-E174 Bedienungsanleitung

Planet

Planet WTB-1000 Bedienungsanleitung

Planet

Planet IHD-410PT Bedienungsanleitung

Planet

Planet IHD-200PT Bedienungsanleitung

Planet

Planet VC-205PT Bedienungsanleitung

Planet

Planet POE-E301 Bedienungsanleitung

Planet

Planet WBT-1000 Bedienungsanleitung

Planet

Planet POE-E101 Bedienungsanleitung

Planet

Planet IVC-2002 Bedienungsanleitung

Planet

Planet WNAP-1110 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung