Planet IVC-234GT Bedienungsanleitung
Industrial 1-Port BNC/RJ11 to 4-Port Gigabit
Ethernet Extender
IVC-234GT
User’s Manual
Trademarks
Copyright © PLANET Technology Corp. 2018.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or tness for a particular
purpose.
PLANET has made every effort to ensure that this User’s Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions
that may have occurred.
Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET
assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep
current the information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the
device from the power circuit. Without removing power cable, the
device will still consume power from the power source. In view of
Saving the Energy and reducing the unnecessary power consumption, it
is strongly suggested to remove the power connection for the device if
this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances
in electrical and electronic equipment, end users of electrical
and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET Industrial 1-Port BNC/RJ11 to 4-Port Gigabit Ethernet Extender
User’s Manual
For Models:IVC-234GT
Revision:1.0 (May 2018)
Part No.: 2350-AC0530-000
Table of Contents
1. Package Contents ....................................................................... 5
2. Hardware Introduction................................................................. 6
2.1 Physical Dimensions.............................................................. 6
2.2 Front View ........................................................................... 7
2.3 Top View ............................................................................. 8
2.4 IVC-234GT LED Indicators..................................................... 8
2.5 DIP Switch and Link Type...................................................... 9
3. Product Specications.................................................................12
4. Applications ...............................................................................14
4.1 Point-to-Point Application -- LAN to LAN Connection ...............14
4.2 Point to Multi-point Application (IP surveillance) .....................16
5. Installations...............................................................................17
5.1 Wiring the Power Inputs ......................................................17
5.2 Wiring the Fault Alarm Contact .............................................18
5.3 DIN-rail Mounting Installation ...............................................19
5.4 Wall-mount Plate Mounting...................................................21
6. Performance Table......................................................................22
7. Troubleshooting .........................................................................24
8. FAQs.........................................................................................25
9. Customer Support......................................................................26
5
1. Package Contents
Thank you for purchasing PLANET Industrial 1-Port BNC/RJ11 to 4-Port
Gigabit Ethernet Extender, IVC-234GT. In the following sections, the
term “Industrial Ethernet Extender” means the IVC-234GT.
Open the box of the Industrial Ethernet Extender and carefully unpack
it. The box should contain the following items:
Industrial Ethernet Extender x 1 User’s Manual x 1
RJ11/RJ45 Dust Caps Wall-mount Kit
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
6
2. Hardware Introduction
2.1 Physical Dimensions
Dimensions (W x D x H): 32 x 135 x 87.8mm
1 2 3 4
ON
P1 P2
CPE CO
VDSL
FAULT
BNC
BNC RJ11
RJ11
4
3
2
1
1000
10/
100
CO
G.INP
Asymm
12dB
CPE
Inter
Symm
8dB
Input
DC12~48V, AC 24V
V1+ V1- V2+ V2-
PWR1 PWR2Fault
1A@24V
Top View
Side View Front View
Mounting Kit
Mounting Kit
DIN-Rail Kit
Side View Rear View
Dimensions ( unit = mm )
Bottom View
Figure 2-1: IVC-234GT Three-View Diagram
7
2.2 Front View
Front Panel
1 2 3 4
ON
P1 P2
CPE CO
VDSL
FAULT
BNC
BNC RJ11
RJ11
4
3
2
1
1000
10/
100
CO
G.INP
Asymm
12dB
CPE
Inter
Symm
8dB
VDSL Port
Figure 2-2: IVC-234GT Front Panel
The unit’s front panel provides the following simple interfaces:
LEDs for Power 1, Power 2 and VDSL2
4 10/100/1000BASE-T RJ45 ports
BNC female/ RJ11 connector via DIP switch
Selectable CO/CPE mode, Target Band Plan and Target SNR Margin
via DIP switch
8
2.3 Top View
The upper panel of the Industrial Ethernet Extender consists of one
terminal block connector within two DC power inputs.
Input
DC12~48V, AC 24V
V1+ V1- V2+ V2-
PWR1 PWR2Fault
1A@24V
1 2 3 4 5 6
Figure 2-3: IVC-234GT Top View
2.4 IVC-234GT LED Indicators
The rich diagnostic LEDs on the front panel can provide the operating
status of individual port and whole system.
System
LED Color Function
P1 Green Lights to indicate DC power input 1 has power.
P2 Green Lights to indicate DC power input 2 has power.
Fault Red Lights to indicate that DC power has failed.
VDSL
LED Color Function
VDSL Green
Lit Indicates that the VDSL connection is
established.
Fast
Blink
Indicates that the VDSL connection is in
training status (about 15 seconds).
Slow
Blink
Indicates that the VDSL connection is in idle
status.
CO Green Lit Indicates the Industrial Ethernet Extender is
running in CO mode.
CPE Green Lit Indicates the Industrial Ethernet Extender is
running in CPE mode.
9
100/1000BASE-T Port
LED Color Function
1000 Green
Lit Indicates that the port is operating at
1000Mbps.
Blink
Indicates that the Industrial Ethernet
Extender is actively sending or receiving
data over that port at 1000Mbps.
Off Indicates that the port is link down or
10/100Mbps.
10/100 Green
Lit Indicates that the port is operating at
100Mbps or 10Mbps.
Blink
Indicates that the Industrial Ethernet
Extender is actively sending or receiving data
over that port at 100Mbps or 10Mbps.
Off Indicates that the port is link down or
1000Mbps.
2.5 DIP Switch and Link Type
Link Type
The BNC mode allows Industrial Ethernet Extender to connect and
transfer data by using BNC cable.
The RJ11 mode allows Industrial Ethernet Extender to connect and
transfer data by using telephone wire
DIP Switch
The Industrial Ethernet Extender provides a selectable 4-position DIP
switch. Switch them on or off to obtain the best coaxial/RJ11 cable
connection over a distance.
DIP DIP-1 DIP-2 DIP-3 DIP-4
Mode Transmission Band Prole SNR Margin
OFF CO G.INP Asymmetric 12dB
ON (default) CPE Interleave Symmetric 8dB
10
Note
By default, the 4-position switches of the DIP switch, set
at the “ON” position, are operated as “CPE”. For oper-
ating as “CO”, please turn DIP 1 switch to the “OFF”
position. Then adjust other DIP switches accordingly to
fulfill different network application demands.
DIP-1: Mode (CO / CPE)
CO (Central
Ofce)
The Master device mode, usually the CO device, is
located at the data center of ISP or enterprise to link to
the backbone.
CPE
(Customer
Premises
Equipment)
The Slave device mode, usually the CPE device, is
located at branch ofce, home or remote side as the
long reach data receiver. The CPE can be connected to
the PC, IP camera or wireless access point, or other
network devices.
Note
When the Industrial Ethernet Extender operates in CPE
mode, DIP switches 2, 3, and 4 are without function.
DIP-2: Transmission (G. INP and Interleave mode)
G. INP Method of protection against bursts from other devices
or lines to impact your xDSL connection.
Interleave
Method of error correction used on xDSL connection.
Interleave requires additional latency to improve
resilience to burst of error.
Inhaltsverzeichnis
Andere Planet Extender Handbücher
Planet
Planet WBT-1000 Bedienungsanleitung
Planet
Planet IPOE-E172 Bedienungsanleitung
Planet
Planet LRE-101 Bedienungsanleitung
Planet
Planet PL-510W Bedienungsanleitung
Planet
Planet LRE-104 Bedienungsanleitung
Planet
Planet IPOE-E174 Bedienungsanleitung
Planet
Planet IPOE-E174 Bedienungsanleitung
Planet
Planet IVC-2002 Bedienungsanleitung
Planet
Planet WNAP-C3220 Bedienungsanleitung
Planet
Planet IPOE-E174 Bedienungsanleitung
Planet
Planet IVC-4011-T-V2 Bedienungsanleitung
Planet
Planet IPOE-E202 Bedienungsanleitung
Planet
Planet WNAP-1110 Bedienungsanleitung
Planet
Planet VC-203PT Bedienungsanleitung
Planet
Planet WNAP-C3220 Bedienungsanleitung
Planet
Planet POE-E201 Bedienungsanleitung
Planet
Planet WGS-E304PT Bedienungsanleitung
Planet
Planet LRE-101C Bedienungsanleitung
Planet
Planet LRP-101C-KIT Bedienungsanleitung
Planet
Planet LRP-101CE Bedienungsanleitung
