Planet IFGS-1022TF Bedienungsanleitung

Industrial 8-Port 10/100TX +

2-Port Gigabit TP/SFP Combo Ethernet Switch

IFGS-1022TF

User’s Manual

Table of Contents

1. Package Contents................................................................................. 3

2. ProductSpecications ........................................................................... 4

3. Hardware Introduction .......................................................................... 6

3.1 Switch Front Panel......................................................................... 6

 3.2 LEDDenition ............................................................................... 7

3.3 Switch Upper Panel........................................................................ 8

3.4 Wiring the Power Inputs................................................................. 8

3.5 Wiring the Fault Alarm Contact ....................................................... 9

4. Installation .........................................................................................10

4.1 DIN-rail Mounting Installation ........................................................10

4.2 Wall-mount Plate Mounting ............................................................10

4.3 Side Wall-mount Plate Mounting.....................................................11

4.4 Grounding the Device....................................................................11

Customer Support.....................................................................................12

1. Package Contents

Thank you for purchasing PLANET Industrial 8-Port 10/100TX + 2-Port Gigabit

TP/SFP Combo Ethernet Switch, IFGS-1022TF. In the following sections, the

term “Industrial Ethernet Switch” means the IFGS-1022TF.

Open the box of the Industrial Ethernet Switch and carefully unpack it. The

box should contain the following items:

Industrial Ethernet Switch x 1 QR code sheet x 1

DIN-rail Kit Wall-mount Kit

RJ45 Dust Cap x 10 SFP Dust Cap x 2

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing

material, and use them again to repack the product in case there is a need to

return it to us for repair.

2.ProductSpecications

Product IFGS-1022TF

HardwareSpecications

Fast Ethernet Copper Ports 8 x 10/100BASE-TX RJ45 auto-MDI/MDI-X ports

Gigabit Ethernet Copper

Ports

2 x 10/100/1000BASE-T RJ45 auto-MDI/MDI-X

ports

(shared with Port 9 and Port 10)

SFP Ports 2 x 1000BASE-SX/LX/BX SFP interfaces

(shared with Port 9 and Port 10)

Enclosure IP30 metal case

Installation DIN-rail kit and wall-mount kit

Connector

Removable 6-pin terminal block for power input

Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin

5/6 for Power 2

Alarm One relay output for power failure. Alarm relay

current carry ability: 1A @ 24V DC

Dimensions (W x D x H) 50 x 87.8 x 135 mm

Weight 534g

Power Requirements Dual 9~48V DC, 24V AC

Power Consumption Max. 12.3 watts/42BTU

ESD Protection 6KV DC

SwitchingSpecications

Switch Architecture Store-and-Forward

Switch Fabric 5.6Gbps (non-blocking)

Throughput

(packet per second) 4.16Mpps@ 64 bytes

Address Table 16K entries, automatic source address learning

and aging

SharedDataBuer 4Mbits

Jumbo Frame 10K bytes

Flow Control IEEE 802.3x pause frame for full-duplex

Back pressure for half-duplex

Standards Conformance

Regulatory Compliance FCC Part 15 Class A, CE

Stability Testing

IEC60068-2-32 (free fall)

IEC60068-2-27 (shock)

IEC60068-2-6 (vibration)

Standards Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000T

IEEE 802.3z Gigabit SX/LX

IEEE802.3xowcontrolandbackpressure

IEEE 802.1p Class of Service

IEEE802.3azEnergyEcientEthernet(EEE)

Environment

Operating Temperature -40 ~ 75 degrees C

Storage Temperature -40 ~ 85 degrees C

Humidity 5 ~ 95% (non-condensing)

3. Hardware Introduction

3.1 Switch Front Panel

The front panel of the Industrial Ethernet Switch consists of Ethernet interfaces

and LED indicators.

Front View

LNK/ACT

1 2

3 4

5 6

7 8

P2 Alarm

IFGS-1022TF

ACTLNK

1000

109

910

Figure 1: I FGS-1022TF Front View

3.2 LEDDenition

System

LED Color Function

P1 Green Lights to indicate power input 1 has power.

P2 Green Lights to indicate power input 2 has power.

Alarm Red Lights: indicates either power 1 or power 2 has no power.

Per 10/100BASE-TX Port

LED Color Function

LNK/

ACT Green

Lights to indicate that the port is operating at

10/100Mbps.

Blinking to indicate that the switch is actively sending or

receiving data over that port.

Otoindicatethattheportislinkeddown.

Per Gigabit RJ45 Combo Interface (Port-9~Port-10)

LED Color Function

LNK/

ACT Green

Lights to indicate the link through that port is successfully

established.

Blinking to indicate that the switch is actively sending or

receiving data over that port.

Otoindicatethattheportislinkeddown.

1000

Speed Amber Lights to indicate that the port is operating at 1000Mbps.

Otoindicatethattheportisoperatingat10/100Mbps.

Per SFP+ Combo Interface (Port 9~Port 10)

LED Color Function

1000

LNK/

ACT

Green

Lights to indicate that the port is operating at 1000Mbps.

Blinking to indicate that the switch is actively sending or

receiving data over that port.

Otoindicatethattheportislinkeddown.

3.3 Switch Upper Panel

The upper panel of the Industrial Ethernet Switch consists of one terminal

block connector within two power input and one relay output.

Max. Fault Alarm Loading: 24V, 1A

DC Input: 9-48V , 0.8A max.

AC Input: 24V , 0.4A max.

PWR1 PWR2

Alarm

1 2 3 4 5 6

Figure 1: IFGS-1022TF Top View

3.4 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Industrial Ethernet

Switch is used for two redundant power inputs. Please follow the steps below

to insert the power wire.

When performing any of the procedures like inserting the wires

or tightening the wire-clamp screws, make sure the power is

OFF to prevent from getting an electric shock.

1. Insert positive and negative DC power wires into contacts 1 and 2 for

POWER 1, or contacts 5 and 6 for POWER 2.

Max. Fault Alarm Loading: 24V, 1A

DC Input: 9-48V , 0.8A max.

AC Input: 24V , 0.4A max.

PWR1 PWR2

Alarm

1 2 3 4 5 6

2. Tighten the wire-clamp screws for preventing the wires from loosening.

123456

Power 1 Alarm Power 2

+ - + -

1. The wire gauge for the terminal block should be in the range

between 12 and 24 AWG.

2. The power input range is 9V ~ 48V DC and supports 24V AC.

3.5 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block connector as

the picture shows below. Inserting the wires, the Industrial Ethernet Switch

will detect the fault status of the power failure and then forms an open circuit.

The following illustration shows an application example for wiring the fault

alarm contacts.

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Alarm

Insert the wires into the fault alarm contacts

1. The wire gauge for the terminal block should be in the range

between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 24V DC, 1A.

4. Installation

This section describes the functionalities of the Industrial Ethernet Switch’s

components and guides you to installing it on the DIN rail and wall. Please

read this chapter completely before continuing.

This following pictures show how to install the device. However,

the device in the picture is not IFGS-1022TF.

4.1 DIN-rail Mounting Installation

4.2 Wall-mount Plate Mounting

Inhaltsverzeichnis

Andere Planet Schalten Handbücher

Planet

Planet IFGS-1022HPT Bedienungsanleitung

Planet

Planet FSD-808P Bedienungsanleitung

Planet

Planet FSD-1008HP Bedienungsanleitung

Planet

Planet WGSW-48000 Bedienungsanleitung

Planet

Planet FSD-504HP Bedienungsanleitung

Planet

Planet gsw-1820vhp Bedienungsanleitung

Planet

Planet GSW-1601 Bedienungsanleitung

Planet

Planet KVM-210 M Series Bedienungsanleitung

Planet

Planet WGSW-52040 Bedienungsanleitung

Planet

Planet IGS-5225 Series Bedienungsanleitung

Planet

Planet IGS-10020PT Bedienungsanleitung

Planet

Planet PL-401E Bedienungsanleitung

Planet

Planet DSP-1000 Bedienungsanleitung

Planet

Planet WSW-2401A Bedienungsanleitung

Planet

Planet POE-1200G Bedienungsanleitung

Planet

Planet XGS-6350-48X2Q4C Bedienungsanleitung

Planet

Planet FNSW-2401CS Bedienungsanleitung

Planet

Planet GS-5220-16S8CR Bedienungsanleitung

Planet

Planet FSD-1605 Bedienungsanleitung

Planet

Planet IKVM-8020 Bedienungsanleitung

Planet

Planet GSD-503 Bedienungsanleitung

Planet

Planet GS-5220 Series Bedienungsanleitung

Planet

Planet FSD-604HP Bedienungsanleitung

Planet

Planet FSD-504HP Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung