Planet WAP-1963 Bedienungsanleitung

Wireless Access Point

WAP-1963

User s Manual

be reproduced, transmitted, transcribed, stored in aretrieval system, or translated into any language or

computerlanguage,in any formorby any means, electronic, mechanical,magnetic, optical, chemical,

manual orotherwise, without the prior written permission of PLANET.

PLANETmakes no representations or warranties,either expressed orimplied,with respectto the

contentshereofand specifically disclaims any warranties,merchantability orfitness forany particular

purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove

defective following their purchase,the buyer (and not PLANET,itsdistributor,or itsdealer)assumes

the entire cost of all necessary servicing, repair,and any incidental or consequential damages resulting

from any defect in the software. Further,PLANETreserves the right to revise this publication and to

make changes from time to time in the contentshereof without obligation tonotify any person of such

revision or changes.

All brand and product names mentioned in this manual aretrademarks and/or registered trademarks of

their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found tocomply with the limitsfor aClass Bdigital device,

pursuant to Part 15 of FCC Rules. These limitsare designed to provide reasonable protection against

harmful interference in aresidential installation. This equipment generates, uses, and can radiateradio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However,there is no guarantee that interference will not occur in

aparticular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correctthe interference by one or more of the following measures:

1.Reorientor relocate the receiving antenna.

2.Increase the separation between the equipmentand receiver.

3.Connect the equipment intoan outlet on acircuit different from that to which the receiver is

connected.

4.Consult the dealer or an experienced radio technician forhelp.

FCC Caution

Toassurecontinued compliance. (example-use only shielded interface cables when connecting to

computeror peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two

conditions:( 1 ) This device may not cause harmful interference, and ( 2 ) this Device mustaccept any

interference received, including interference thatmay cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In

order to avoid the possibility ofexceeding the FCC radio frequency exposure limits, human proximity to

the antenna shall not be less than 20 cm (8 inches) during normal operation.

R&TTE Compliance Statement

This equipmentcomplies with all the requirementsof DIRECTIVE 1999/5/CE OF THE EUROPEAN

PARLIAMENTAND THE COUNCILOF 9March 1999 on radio equipment and telecommunication

terminal Equipment and the mutual recognition of theirconformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal

Equipmentand Satellite EarthStation Equipment) As of April 8,2000.

Safety

This equipment is designed with the utmost carefor the safety of those who install and use it. However,

special attention must be paid to the dangersof electric shock and static electricity when working with

electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed

at all times to ensure the safe use of the equipment.

EU Countries Not Intended for Use

The ETSI version ofthis device is intended forhome and office use in Austria Belgium,Denmark,

Finland, France (with Frequency channel restrictions). Germany,Greece, Ireland, Italy,

Luxembourg .The Netherlands, Portugal, Spain, Sweden and United Kingdom.

The ETSIversion of this device is also authorized foruse in EFTAmember states Iceland,

Liechtenstein, Norway and Switzerland.

Potential restrictive use

France: Only channels 10,11,12 and 13

Revision

User s Manual for PLANET Wireless Access Point

Model: WAP-1963

Rev: 1.0 (November,2003)

Part No. EM-WAP1963

TABLE OF CONTENTS

Chapter 1 Introduction1

1.1 Package Contents1

1.2 System Requirements1

1.3 Features1

1.4 Specification 2

Chapter 2 Hardware Installation3

2.1 Hardware Connection3

Chapter 3 Configuration 4

3.1 Configurethrough Web Browser 4

3.1.1 Home: 5

3.1.2 Wireless Settings: 6

3.1.3 Wireless AdvanceSettings: 8

3.1.4 Security: 12

3.1.5 MAC Filtering: 14

3.1.6 SystemUtility: 16

3.1.7 ConfigurationTool 18

3.1.8 Upgrade 19

3.1.9 Reset 20

Chapter 4 Application 21

4.1 Access Point mode21

4.2 Wireless Station mode21

Chapter 5 Troubleshooting 22

Chapter 1 Introduction

Thank you for purchasing WAP-1963.This device is an access point for IEEE 802.11b 2.4GHz wireless

network. You can use this access point tobuild up awireless LAN, any wireless LAN station can join the

wireless network. It has support 64/128-bit WEP (Wired Equivalent Privacy) Encryption and MAC

address filter function toconsolidatethe wireless network security,you can preventunauthorized

wireless stations from accessing your wireless network.

WithitsStation mode, thatcan served as awireless station (Infrastructureor Ad-Hoc).Connected to

you LAN, it is able toaccess the network via Access Point or join toasmall wireless network without

Access Points. It sdatarate support 11, 5.5, 2and 1Mbps. Maximize network efficiency while minimizing

your network investment and maintenance costs.

This productprovides easy to use userinterface and allows usersto configuring from web browser.Also

it integrates DHCP server to provide multiple wireless and wired usersto get an IP address automatically.

Withthe versatile offeatures, this productis the best choice for you to integrate your wireless and wired

network seamlessly.

1.1Package Contents

Make sure that you have the following items:

• One WAP-1963

• One AC Power Adapter

• One User s Manual CD

• One Quick Installation Guide

• One External Antenna

Note:

If any of the above items are missing, contact your supplier as soon as

possible.

1.2System Requirements

Before installation, please check the following requirementswith your equipment.

• Pentium Based (And Above) IBM-Compatible PC System

• CD-ROMdrive

• Windows 98/ME/2000/XP/Server2003 Operating System with TCP/IP protocol

1.3Features

Compliant with the IEEE 802.11b (DSSS) 2.4GHz specification

High data rate 11,5.5,2 and 1Mbps network speed, Auto rate fallback

Seamlessly integrate wireless and wired EthernetLAN networks

Interferences Provide 64/128-bit WEPEncryption and MAC Filter to protect the wireless data

transmissions

SupportsWireless AP/Station mode

Built-in DHCPserver supportsauto IP addresses assignment

Web-based configuration

Auto Fall-Back Data Rate forLong-Distance Communication and Noisy Environments

1.4 Specification

Standard IEEE 802.11b Compliant

Signal Type DSSS (Direct Sequence Spread Spectrum)

Modulation QPSK / BPSK / CCK

Port One 10/100BASE-TX

Antenna One Dipole Antenna

Data Encryption 64 bit / 128 bit WEPencryption

Frequency 2.4GHz - 2.4835GHz

Channel 11 Channels (US/ Canada, FCC)

13 Channels (Europe, ETSI)

14 Channels (Japan, TELEC)

Data Rate Up to 11Mbps(with automatic scale back)

Range Coverage

(In Open Environment)

11M448 feet = 140m

5.5M640 feet = 200m

2M864 feet = 270m

1M1100 feet = 340m

LED Indicators PWR, WLAN, LAN

Power Requirement 12V DC, 0.5A

Temperature Operating :0 ~ 55 degree C

Storage: -20 ~ 70 degree C

Humidity Operating: 10 ~ 90%

Storage: 10 ~ 90% Non-Condensing

Dimensions 160 x87 x28 mm

Output Power 18dBm

Antenna Gain 2dBi

Antenna Connector Reversed Polarity SMAMale

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the

WAP-1963.

2.1HardwareConnection

12V DC

LAN RESETANT

1. Locate an optimum location for the WAP-1963. Thebestplace for your WAP-1963 is usually

at the center of your wireless network, with line of sight to all of your mobile stations.

2. Assemble the antennas to WAP-1963. Try to place them to aposition that can best cover your

wireless network. The antenna sposition will enhance the receiving sensitivity.

3. Connect RJ-45 cable to WAP-1963. Connect this WAP-1963 to your LAN switch/hub or a single

PC.

4. Plug in power adapter and connect topower source.After power on, WAP-1963 will start to

work.

Note: ONLYuse the power adapter supplied with the WAP-1963. Otherwise, the product may be

damaged.

If you want to reset your WAP-

1963 to default settings, press the Reset button 5 second.And

then wait for10 seconds for WAP-1963 restart.

Chapter 3 Configuration

3.1 Configurethrough Web Browser

Web configuration provides auser-friendly graphical user interface (web pages)to manage your

WAP-1963.An APwith an assigned IPaddress (e.g. http://192.168.0.1)will allowyou via web browser

(e.g., MS Internet Explorer or Netscape) to monitor and configure.

1. Open your web browser.

2. Enter WAP-1963 IP address (default IP address is http://192.168.0.1)intothe address field of the web

browser. Please also make sure your PC s IPaddress is in the same IP range of WAP-1963.

3. AUser Name and Password dialog boxwill appear.Please enter your User Name and Password here.

DefaultUser Name and Password is “admin”and “admin”. Click “OK”.

4. Then you will see the WAP-1963 information in the web page as the picture in section 3.1.1.

3.1.1 Home:

On this screen,you can see the general information ofthe Access Pointincluding Alias Name,

Firmware Version,SSID,Channel Number,Security,Number ofAssociated Clients,IP Address,MAC

Address, etc.

3.1.2 Wireless Setting:

In this option, you can set the Mode, Alias Name, ESSID and Work Channel to this Access Point.

When configuration finished, please click “Apply”to save.

3.1.2.1AP MODE

This mode is set to WAP-1963 by default. Itserved as atransparent Media Access Control (MAC)

bridge between wired and wireless network.

Parameters Description

Alias Name The alias name of this access point.

ESSID The ESSID (up to 31 printable ASCII characters) is the unique name identified in a

WLAN. The ID prevents the unintentional merging of two co-located WLANs.

Please make sure thatthe ESSID ofall stations in the same WLANnetwork are the

same. The default ESSID is “default”.

Channel Number Select the appropriate channel from the list provided to correspond with your

network settings. Channels differ from country to country.

Channel 1-11 (North America)

Channel 1-14 (Japan)

Inhaltsverzeichnis

Andere Planet Drahtloser Zugangspunkt Handbücher

Planet

Planet MAP-3100 Kurzanleitung

Planet

Planet RTL8812AU-CG Bedienungsanleitung

Planet

Planet WNAP-6350 Bedienungsanleitung

Planet

Planet WNAP-W2200UE Bedienungsanleitung

Planet

Planet WNAP-1110 Bedienungsanleitung

Planet

Planet WDAP-C3000AX Bedienungsanleitung

Planet

Planet WAP-6200 Bedienungsanleitung

Planet

Planet 802.11g Wireless Access Point / Bridge... Bedienungsanleitung

Planet

Planet WAP-4030A Bedienungsanleitung

Planet

Planet WNAP-6350 Bedienungsanleitung

Planet

Planet WDAP-C7200AC Bedienungsanleitung

Planet

Planet WNAP-7205 Bedienungsanleitung

Planet

Planet WDAP-C7200AC Bedienungsanleitung

Planet

Planet WDAP-C3000AX Bedienungsanleitung

Planet

Planet WNAP-7350 Bedienungsanleitung

Planet

Planet IAP-2000PS Bedienungsanleitung

Planet

Planet IAP-1800AX Bedienungsanleitung

Planet

Planet WAP-4060PE Bedienungsanleitung

Planet

Planet WDAP-W7200AC Bedienungsanleitung

Planet

Planet MAP-3120 Programmierhandbuch

Planet

Planet WNAP-3000PE Bedienungsanleitung

Planet

Planet WAP-252N Bedienungsanleitung

Planet

Planet WDAP-702AC Bedienungsanleitung

Planet

Planet WDAP-W1200E Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung