Planex GW-AP11S Bedienungsanleitung

11Mbps WIRELESS LAN ACCESS POINT

GW-AP11S/AP11T

11Mbps WIRELESS LAN ACCESS POINT

GW-AP11S/AP11T

USER'S MANUAL

Trademarks

Contents subject to change without prior notice.

Pci is a registered trademark of PLANEX COMMUNICATIONS INC.

All other trademarks belong to their respective proprietors.

No part of this publication may be reproduced in any form or by any means

or used to make any derivative such as translation, transformation, or

adaptation without permission from PLANEX COMUNICATIONS INC.

FCC Warning

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with this user's guide, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

●Reorient or relocate the receiving antenna

●Increase the separation between the equipment and the receiver

●Connect the equipment into an outlet on a circuit different from the one

which the receiver is connected to

●Consult the dealer or an experienced radio/TV technician for help

You are cautioned that changes or modifications not expressly approved by

the party responsible for compliance could void your authority to operate

the equipment.

Warnings: Wear an antistatic wrist strap to take other suitable measures to

prevent electrostatic discharge whenever handling the equipment.

VCCI Note

This is a VCCI Class B product.

Appendix A

Appendix B

Version:1.0 E Rev.A

Chapter 2

Installation

Explains how to install the GW-

AP11S/AP11T on your computer.

About this Manual

Appendices

Chapter 1

Introduction

Provoides product overview and parts

terminology. Please be sure to read this

chapter first.

Environmental Requirements

Provides environmental factors to keep in mind when you install the wireless LAN access

point.

This manual contains the following chapters and apprnices:

Specifications.

Provides the technical product specifications of the GW-AP11S/AP11T

Chapter 3

Software Installation

Describes how to install the 1.USB Driver and the 2.Configuration Utility of the GW-

AP11S/AP11T

Chapter 4

Setting Up the Access Point via USB

Config Utility

Explains how to use the supplied utility to

configure the product via USB.

Chapter 5

Setting Up the Access Point via SNMP

Utility.

Describes how to use the supplied utility

to configure the product via the SNMP

protocol.

Verifying the Installation..................................

Deleting the USB Driver....................................

Installing the Access Point Utility....................

Chapter 4 Setting Up the Access Point via

USB Config Utility......................

Chapter 5 Setting Up the Access Point via

SMNP Utility

Main Window ...................................................

Configuration Window.....................................

Appendix A

Environmental Requirements............................

Appendix B

Specifications ....................................................

GW-AP11S/AP11T

Chapter 1 Introduction

Product Overview ............................................

Features ............................................................

Package List......................................................

Parts Terminology...........................................

Chapter 2 Installation

Environmental Requirements ........................

Installing the Access Point...............................

Connecting the AC Adapter to the GW-AP11S/AP11T

............................................................................

Connecting the GW-AP11S to a Hub............

Connecting the GW-AP11S to a PC

....................

Selecting the Operation Mode of the GW-AP11S/AP11T

...........................................................................

Chapter 3 Software Installation

Installing the USB Driver ...............................

1 2

Chapter 1

Introduction

The GW-AP11S is a bridge that interfaces between a wireless LAN network

and an existing Ethernet network. By using the GW-AP11S/AP11T Access

Point, you can seamlessly establish and integrate a wireless LAN network

into your existing Ethernet network and resources therein. The Access Point

complies with IEEE802.11 and IEEE802.11b, and supports data transfer at

11Mbps/5.5Mbps/2Mbps and 1Mbps. As the device supports Roaming,

wireless nodes (users) can communicate with other nodes while they move

between service sets: the users need not specify or detect a new access

point. The GW-AP11S/AP11T also utilizes powerful security features

including ESSID and WEP to protect the network from unauthorized

accesses.

1-1 Sample Wireless LAN Layout

11Overview

GW-AP11S/AP11T

The product package should contain the following items:

●GW-AP11S.AP11T Wireless LAN Access Point

●AC adapter

●Setup Utility CD-ROM

●This user's manual

●USB cable

If any item is found missing or damaged, please contact your local PCI

reseller or our technical support for replacement.

A movable diversity antenna is equipped on top of the GW-AP11S/AP11T.

1-2 GW-AP11S Front View

GW-AP11S/AP11T

●Complies with IEEE 802.11/802.11b

●Supports IEEE802.3 10BASE-T

●USB 1.1 compliant

●Complies with ARIB STD-33A/STD-T66

●Noise-resistant DS-SS data transfer scheme

●Frequency range: 2.4Ghz (14 channels)

●Automatically detects appropriate speed (11Mbps/5.5Mbps/2Mbps/

1Mbps)

●Robust network security achieved via ESSID, WEP and MAC address

filtering

●Communication range: 100m maximum (line-of-sight distance, indoor

use)

●Employs a highly sensitive diversity antenna

●3 LED indicators clearly indicate the working status of the access point

●Equipped with a USB port for configuration via a console running a

management utility

●Supports Inter-AP (AP-to-AP) Communication Mode

●Supports Station Mode which incorporates existing network cards and

print servers into a wireless LAN

●Supports Roaming: the users can freely move among different access

points

●Comes with a setup utility

12Features 13Packing List

14Parts Terminology

GW-AP11S/AP11T

The rear panel of the access point provides a USB port and an RJ-45 port.

A PC can be attached to the USB port on the GW-AP11S/AP11T to

configure the product, while the RJ-45 port is used to connect the product to

a hub.

1-3 Rear View

Power Jack:

The supplied AC adapter attaches to this DC power jack.

RJ-45 Port:

A 10BASE-T twisted-pair cable connects to this RJ-45 port.

This port serves as an Uplink port.

USB:

This port is used to configure the access point via a PC running the supplied

management (configuration) utility.

GW-AP11S/AP11T

1-3 GW-AP11T Front View

The on-board three LED's indicate the working status of the access point:

Power LED:

This LED illuminates when the power of the access point is turned on.

LAN LED:

This LED glows whenever a 10Mbps data link is established on the port.

Wireless:

The LED flashes when the wireless interface is available.

GW-AP11S/AP11T

Before proceeding, please take a minute to review the safety guidelines

described in the Safety Instructions above. Also, be sure to follow the

additional guidelines below.

●Do not place the product in a damp or wet location.

●Always avoid dust and dirt.

●Do not install the product in an area exposed to direct sunlight.

●Allow some space between the product and the surroundings to facilitate

dissipation of heat generated inside the hub.

Always place the product on a level surface (ex. desktop).

Avoid placement on an unstable (or uneven) surface.

1. Attach the supplied AC adapter to the power jack on the rear panel.

2. Connect the AC adapter to a wall outlet.

3. Verify that the Power LED on the front panel illuminates.

Caution:

Use only the supplied AC adapter. Any attempt to use another AC adapter

may result in malfunction of and/or serious damage to the switch. The

product warranty does not support damages caused by the use of an

unsupported AC adapter.

Chapter 2

Installation

21Environmental Requirements

22Installing the Access Point

Connecting the AC Adapter to the GW-

AP11S/AO11T

To attach the GW-AP11S/AP11T to a wireless LAN and a wired LAN, the

product must be first connected to a hub.

1. Prepare a twisted-pair cable with RJ-45 plugs at both ends. Cable length

should not exceed 100 meters (328 feet), and cable type must be Category

3, 4 or 5.

2. Attach one end of the cable to one of the normal RJ-45 ports on the hub.

3. Attach the other end of the able to the LAN port on the Access Point. The

LAN LED will illuminate if the hub is working properly.

To use the access point in Station Mode, the LAN port on the product must

be directly connected to the LAN port of your PC via a crossover LAN

cable.

1. Obtain a crossover LAN cable. Its length should not exceed 100 meters.

2. Attach one end of the LAN cable to the LAN port of your PC.

3. Attach the other end of the crossover cable to the LAN port on the access

point. The LAN LED on the front panel will illuminate if the LAN port

(adapter) on the PC is working properly.

While the GW-AP11S/AP11T functions as an IEEE802.11b access point, it

also supports the following two operation modes:

GW-AP11S/AP11T

■Station Mode

In this mode, the access point (AP) is attached to the LAN port of a PC to

serve as a client on a wireless network. This mode supports Infrastructure

Mode as defined in IEEE802.11b. By connecting the access point to a PC

preinstalled with a network card, you can add the AP to your wireless

network as a member node.

2-1 Station (Infrastructure) Mode

■Inter-AP Communication Mode

This mode enables AP-to-AP communication. In this mode, one AP may

communicate with n (multiple) AP's.

24Connecting the GW-AP11S/AP11T to a Hub

25Connecting the GW-AP11S/AP11T to a PC

Selecting the Operation Mode of the GW-

AP11S/AP11T

Andere Handbücher für GW-AP11S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planex Drahtloser Zugangspunkt Handbücher

Planex

Planex GW-AP54SGX Bedienungsanleitung

Planex

Planex CQW-ID1000 Bedienungsanleitung

Planex

Planex CQW-AP108AG Bedienerhandbuch

Planex

Planex GW-AP54SAG Bedienungsanleitung

Planex

Planex GW-AP54SP-P Bedienungsanleitung

Planex

Planex CQW-ID1000 Bedienungsanleitung

Planex

Planex GW-AP11S Bedienungsanleitung

Planex

Planex GW-AP54SP-P Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung