Playcore DERO Bike Bedienungsanleitung

Bike Bike Rack Setbacks

STREET

WALL

90"

76"

36"

24"

Installation Surface MountBike Bike Rack

RECOMMENDED BASE MATERIAL

Solid concrete is the best base material for installation. To ensure the proper anchors

are shipped with your rack, ask your Dero representative which anchor is appropriate

for your application. Be sure nothing is underneath the base material that could be

damaged by drilling.

TOOLS NEEDED

Tape Measure

Marker or Pencil

Masonry Drill Bit 3/8”

Drill (Hammer drill recommended)

Hammer

Wrench 9/16”

Level

Drill 3/8” diameter holes 3” deep into surface. Make sure the

holes are at least 3” away from any cracks in the base material.

Thread nuts onto anchors, leaving approximately 1/4” of the

anchor protruding, and tap into surface. Tighten nuts down to

secure rack.

Place the rack in the desired location. Use a marker or pencil to

outline the holes of the ﬂange onto the base material.

Use washers to level rack if necessary.

Ø 3/8”

9/16”

3”

Installation In-Ground Mount : New ConcreteBike Bike Rack

TOOLS NEEDED

Level

Cement mixing tub

Shovel

Pour concrete and allow to cure.

An easy way to brace the Bike Bike Rack while the grout sets

is to bolt two 1x4” boards together at one end and clamp them

onto the wheel of the rack like a clothes pin.

Place corrosion resistant sleeve (min. 4” inside diameter) in sand

pour bed in exact location where rack will be installed. Make

sure top of sleeve is at same level as desired ﬁnished concrete

surface. Fill sleeve with sand to keep it in place and prevent it

from ﬁlling with concrete.

After appropriate cure time, dig out sand from sleeves and insert

rack, making sure it is level and at the appropriate height. Pour in

Super Por-Rok or epoxy grout and allow to set.

Trowel

Corrosion-Resistant Sleeve (min. 4” diameter)

Materials to build brace (see “Install Tip” at bottom of page)

Sand pour bed

Sleeves

Final grade level

Poured concrete

(4-7” deep)

TIP

Installation In-Ground Mount : Existing ConcreteBike Bike Rack

TOOLS NEEDED

Level

Cement mixing tub

Shovel

Access to water hose

Fill holes with Super Por-Rok or epoxy grout.

An easy way to brace the rack while the grout sets is to bolt two

1x4” boards together at one end and clamp them onto the wheel

of the rack like a clothes pin.

Core holes no less than 4” diameter and no less than 11” deep

into sidewalk.

Place rack into holes, making sure the rack is level until the grout

has set.

Trowel

Hole coring machine with 4” bit

Materials to build brace (see “Install Tip” at bottom of page)

TIP

Ø 4” min.

11” min.

Installation Footing DiagramsBike Bike Rack

12”

48”

10”

18”

24”

IN-GROUND MOUNT SURFACE MOUNT

(or standard 4” sidewalk slab)

Inhaltsverzeichnis

Andere Playcore Rack & Stand Handbücher

Playcore

Playcore DERO BIKER BAR Bedienungsanleitung

Playcore

Playcore Colorado Time Systems F1057 Bedienungsanleitung

Playcore

Playcore DERO Arc Rack Bedienungsanleitung

Playcore

Playcore DERO BIKE DEPOT Bedienungsanleitung

Playcore

Playcore DERO Cycle Dock Bedienungsanleitung

Playcore

Playcore DERO Round Rack Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung