Plura UD Series Bedienungsanleitung

Installation and Operating Manual

Version: 4.5

September 25, 2019

UD Series Displays

 
Installation and Operating Manual UD Series Displays 
Page 3 
 
 
 
 
CONTENTS 
A1 REVISION HISTORY 
A2 COPYRIGHT 
A3 WARRANTY 
A4 UNPACKING/SHIPPING/REPACKAGING INFORMATION 
A5 SAFETY INSTRUCTIONS 
A6 CERTIFICATIONS & COMPLIANCES 
FUNCTIONAL DESCRIPTION 13 
INTRODUCTION 13 
MODELS 15 
ACCESSORIES AND OPTIONS 17 
EPSW: External AC/DC Power Supply 17 
UD-AP: Optional AC Power Inlet, attached 17 
UD-BP: Optional AC Power Inlet, integrated 17 
UD-PoE: Power over Ethernet 17 
UD56-W: Wall, Tripod, and Table Mount Kit 17 
UD56S, UD56LS and UD56ES: Integrated LED Seconds Ring for UD56 18 
UD300D, UD300LD and UD300ED: Appended Display for UD300 18 
INTERFACES 19 
LTC (MTD) 19 
IRIG 19 
RS485 (MTD) 19 
GPI 20 
RS232/RS422 20 
Ethernet 21 
STATUS AFTER POWER-ON 22 
Displays in LTC, IRIG or serial modes 22 
Displays in Ethernet mode 23 
FIRMWARE UPDATE 24 
CONFIGURATION 25 
The UD/SC Configuration Program 25 
“Profile“ Tab: Store and Load a Complete Set-Up 26 
“System“ Tab: View and Change System Parameters 27 
“Source” Tab: Select the Signal Source 28 
“LTC“ Tab: Set-Up of the LTC Reader 30 
“Serial“ Tab: Set-Up of the Serial Interface 31 
“Ethernet“ Tab: IP Addresses ... 33 
“Real-Time“ Tab: Set the Time Zone Parameters 35 
“Display“ Tab: Display Mode, Brightness, ... 37 
“GPI“ Tab: Programming GPI as Input or Output 39 
SPECIAL FEATURES 43 
Colour Changing Modes 43 
Switching the Display Mode by a Button 44 

 
Installation and Operating Manual UD Series Displays 
Page 4 
 
 
 
 
TECHNICAL DATA 45 
CONNECTIONS AT THE REAR 45 
SPECIFICATIONS 47 
AC/DC POWER SUPPLIES 50 
EPSW: External Power Adapter 50 
UD-AP: Attached AC Power Inlet 51 
UD-BP: Integrated AC Power Inlet 52 
PI: Ethernet Power Injector for UD-PoE 53 
Notes on PoE Operation 55 
Safety Precautions 56 
APPLICATIONS 57 
CONTROLLING MTD STOP TIMERS BY USE OF GPI COMMANDS 57 
MTD SLAVE: LOCAL STOP TIMER AND EXTERNAL DISPLAYS 58 
REAL-TIME DISPLAY WITH A GPS16/GPS17 REFERENCE 59 
REAL-TIME DISPLAY WITH A RUB GPS 10 MHZ REFERENCE 61 
INSTALLATION 63 
TERMINAL BLOCK CONNECTIONS 63 
LTC/MTD LOOP ADAPTER 64 
STRAIN RELIEF FOR CONNECTING CABLES: UTILIZING CABLE TIE HOLDERS 65 
UD56-W: WALL, TRIPOD, AND TABLE MOUNT KIT 66 
UD300: WALL MOUNTING 68 
UD126 + UD178: MOUNTING AND TECHNICAL DATA 69 
UD25TT: SPACE SAVING HOUSING 70 

Installation and Operating Manual UD Series Displays

Page 5

A1 Revision History

No.

Date

Subject

0.x

Preliminary documents, changes without notice.

1.0

August 27, 2008

First released document.

1.1

September 04, 2008

UD56.

1.2

September 15, 2008

UD56E.

Revised.

1.3

October 23, 2008

Operating mode “MTD Slave”.

1.4

October 28, 2008

GPI features.

1.5

November 13, 2008

Operating mode “MTD Slave” extended.

New: Chapter “Special Features –Colour Changing Modes”.

1.6

March 02, 2009

Wall and table mount kit: UD56-W.

UD300.

2.0

March 20, 2009

Completely revised.

2.1

April 29, 2009

Status after power-on and RS232/RS422 revised.

New: Specification of free-run accuracy.

New: Chapter “Real-Time Display with a GPS16/GPS17 Reference”.

New: Chapter “Real-Time Display with a RUB GPS 10 MHz Reference”.

2.2

June 16, 2009

Revised.

New feature “Set Clock” at the “Real-Time” tab.

New feature “Reset+Continue” at the “GPI” tab.

Housing UD25TT.

3.0

March 25, 2010

Revised.

MTDoE and PoE versions.

3.1

April 16, 2010

Revised.

UD-AP: Attached power supply.

New rear with XLR connectors.

3.2

December 02, 2010

UD300LD and UD300ED.

Installation: Cable tie holders.

3.3

December 21, 2010

UD126L (preliminary).

3.4

April 12, 2011

UD126L/UD126E.

UD56 housing: Depth will change from 45 mm to 56 mm.

UD-BP: Integrated power supply.

New GPI functions.

Special features: Switching the display mode by a button.

3.5

May 13, 2011

New GPI features.

3.6

May 30, 2011

Technical data revised.

GPS connection changed regarding PPS input.

3.7

February 10, 2012

Changes at tab “Ethernet”.

New: Store and load “profiles”.

New serial protocols.

New GPI modes.

Description of a “Loop Adapter” for “L” version displays.

3.8

August 10, 2012

Page layout revised.

3.9

August 01, 2013

Tab “Ethernet”: It is possible to enter an IP address of a “Secondary MTD Master”.

UD56-W: Now fitted with tripod screw thread.

3.A

October 23, 2013

UD178L/UD178E.

Table of “Readability/Distance” added to Specifications.

3.B

April 02, 2014

Chapter “System Tab: View and Change System Parameters”: added note if password is lost.

4.0

April 24, 2014

New chapter: “PI: Ethernet Power Injector for Option UD-PoE”.

4.1

May 02, 2014

New chapter: “Notes on PoE Operation”.

Chapter revised: “UD56-W: Wall, Tripod, and Table Mont Kit”.

Chapter revised: “Real-Time Tab: Set the Time Zone Parameters”.

4.2

July 31, 2014

Chapter revised: “Models”.

Chapter revised: “Connections at the Rear”.

Chapter revised: “UD56-W: Wall, Tripod, and Table Mont Kit”.

4.3

May 28, 2015

Added “universal” display versions.

4.4

July 20, 2017

Added DC IN specifications to UD300 / UD300D

4.5

September 25, 2019

Changed address of Plura Europe GmbH.

Installation and Operating Manual UD Series Displays

Page 6

Due to constant product development the features of UD Series Displays are subject to

change. The current functional description always refers to the current firmware and the

current configuration tool. You can download the latest version of the standard firmware from

https://www.plurainc.com

Please be sure to use the latest configuration program after having done an update. You can

download the latest version from the address above.

A2 Copyright

may be reproduced, translated into another language, stored in a retrieval system, or

transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or

otherwise without the prior written consent of Plura Europe GmbH.

Printed in Germany.

Technical changes are reserved.

All brand and product names mentioned herein are used for identification purposes only and

are trademarks or registered trademarks of their respective holders.

Information in this publication replaces all previously published information. Plura Europe

GmbH assumes no responsibility for errors or omissions. Neither is any liability assumed for

damages resulting from the use of the information contained herein.

For further information please contact your local dealer or:

Plura Europe GmbH

Binger Weg 12

D- 55437 Ockenheim

Phone: +49 6725 918 006-70

Fax: +49 6725 918 006-77

E-Mail: info@plurainc.com

Internet: http://www.plurainc.com

Installation and Operating Manual UD Series Displays

Page 7

A3 Warranty

Plura warrants that their products will be free from defects in materials and workmanship for a

period of two years from the date of shipment. If this product proves defective during the

warranty period, Plura, at its option, will repair or replace the defective product without

charge, provided this product is returned to Plura freight prepaid.

In order to obtain service under this warranty, Customer must notify Plura of the defect before

expiration of the warranty period and make suitable arrangements for the performance of

service. Customer shall be responsible for packaging and shipping the defective product to

Plura, please notice the Shipping Information given below.

This warranty shall not apply to any defect, failure or damage caused by abuse, misuse,

improper use, negligence, accident, modification, alteration, or improper or inadequate

maintenance and care.

This warranty is given by Plura with respect to this product in lieu of any other warranties,

express or implied. Plura and its vendors disclaim any implied warranties of merchantability or

fitness for a particular purpose. Plura’s responsibility to repair or replace defective products is

the sole and exclusive remedy provided to the customer for breach of this warranty. Plura and

its vendors will not be liable for any indirect, special, incidental, or consequential damages

irrespective of whether Plura or the vendor has advance notice of the possibility of such

damages.

Installation and Operating Manual UD Series Displays

Page 8

A4 Unpacking/Shipping/Repackaging Information

This product has been carefully inspected, tested and calibrated before shipment to ensure

years of stable and trouble-free service.

The shipping carton and pads provide protection for the product during transit. Retain the

shipping cartons in case subsequent shipment becomes necessary.

Carefully unpack the product from its transit material and carefully check the product for signs

of damage. In the event that the product has been damaged during transit, contact the carrier

and your Plura dealer.

Please confirm that all items listed on the packing list have been received. Check the items

against your original order to ensure that you have received the correct parts. If any item is

missing, please contact your Plura dealer.

Ensure that all packaging material is removed from the product and its associated

components before installing the unit.

Products returned to Plura for servicing or repair should have a tag attached showing:

•Name and complete address of the owner and the name of the person that can be

contacted.

•Unit’s serial number and a description of the service required, or failure detected.

Products returned should be shipped prepaid in the original packaging material if possible. If

the original packaging is not available or is unfit for use, supply an adequate packaging

which should meet the following criteria:

•Packaging must be able to withstand the product weight.

•Product must be held rigid within the packaging.

•Allow at least two inches of space between the product and the container.

•The corners of the product must be protected.

•Seal the carton with shipping tape or an industrial stapler.

If the product is still within the warranty period, the product will be returned by prepaid

shipment after servicing.

Installation and Operating Manual UD Series Displays

Page 9

A5 Safety Instructions

The general safety information in this part is for both operating and service personnel. Plura

products are only to be used as directed. Specific warnings and cautions will be found

throughout the manual where they apply.

Review the following safety instructions to avoid injury and prevent damage to this product or

any products connected to it.

•Read these instructions.

•Keep these instructions.

•Heed all warnings.

•Follow all instructions.

Safety Terms and Symbols

Terms and Symbols in this manual:

WARNING: Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION: Caution statements identify conditions or practices that could result in

damage to this product or other property.

Terms and Symbols which may be found on the product:

ATTENTION: Refer to the manual.

Observe precautions for handling electrostatic-sensitive devices.

Signal Ground.

Product Damage Precautions

PREVENT OVERHEATING

To prevent product overheating, position the unit only where sufficient air

circulation can be maintained. Good air circulation is essential to prevent

internal heat build-up, do not block any ventilation openings. Do not expose the

unit to direct sun light or any other strong lights. Keep the unit away from heat

sources.

PROVIDE PROPER ENVIRONMENT

Dust, humidity, shocks and strong electromagnetic fields must be avoided. Do

not expose this apparatus to dripping or splashing water. Ensure that no objects

filled with liquid are placed on the apparatus.

Installation and Operating Manual UD Series Displays

Page 10

OBSERVE EMC REGULATIONS

The EMC regulations are observed only under the following condition: use high

quality shielded cables at data inputs and outputs.

SUSPECTED FAILURES

Whenever it is likely that safe operation is impaired, the apparatus must be made

inoperative and secured against unintended operation. The appropriate service

authority must then be informed. Do not operate with suspected failures.

Servicing is required when the apparatus has been damaged in any way, such as

power-supply is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

PREVENTIVE MAINTENANCE: CLEANING

Qualified Service Personnel Only: The apparatus should be cleaned often

enough to prevent dust or dirt from accumulating. Dust accumulating in the

apparatus acts as an insulating blanket, preventing proper cooling, and possibly

causing overheating and component breakdown. Under high humidity

conditions, accumulated dust can also provide an electrical conduction path.

Remove accumulated dust with a soft cloth or small paint brush. Remove

hardened dirt with a soft cloth, dampened in a mild detergent and water

solution. Do not use polish or abrasive cleaners or any other chemical cleaning

agents.

PREVENTIVE MAINTENANCE: VISUAL INSPECTION

Qualified Service Personnel Only: Visually inspect the apparatus for signs of

damage, scorched components, and loose or disconnected pin connectors. If you

discover heat damaged parts, try to determine the cause of the overheating

before replacing the damaged parts; otherwise, the damage may repeat.

ATTENTION:

Observe precautions for handling electrostatic-sensitive devices. See “Electrostatic

Discharge (ESD) Precautions” below for details.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Plura Monitor Handbücher

Plura

Plura 3G Series Bedienungsanleitung

Plura

Plura PBM-4K-H Series Bedienungsanleitung

Plura

Plura PBM-4K-H Series Bedienungsanleitung

Plura

Plura PRM-3G Series Bedienungsanleitung

Plura

Plura PBM-217S Bedienungsanleitung

Plura

Plura PBM-070 Bedienungsanleitung

Plura

Plura PBM-224-4K Bedienungsanleitung

Plura

Plura DBM-124 Bedienungsanleitung

Plura

Plura SFP-H Series Bedienungsanleitung

Plura

Plura MVM-124 Bedienungsanleitung

Plura

Plura PRM-3G Series Bedienungsanleitung

Plura

Plura SFP-217-3G Bedienungsanleitung

Plura

Plura PRM-317-3G Bedienungsanleitung

Plura

Plura LCM-119-3G Bedienungsanleitung

Plura

Plura PBM-217 Gebrauchsanweisung

Plura

Plura PBM-4K Series Bedienungsanleitung

Plura

Plura PBM-4K Series Bedienungsanleitung

Plura

Plura SFP-3G Series Bedienungsanleitung

Plura

Plura DBM-124 Bedienungsanleitung

Plura

Plura LCM-3G Bedienungsanleitung

Plura

Plura PHB-207-3G Bedienungsanleitung

Plura

Plura PBM-070 Bedienungsanleitung

Plura

Plura SFP-H Series Bedienungsanleitung

Plura

Plura DBM-152 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung