PNI JL269 Bedienungsanleitung

PNI JL269

Portable gas detector / Tragbarer Gasdetektor / Detector de gas portátil /

Détecteur de gaz portable / Hordozható gázérzékelő / Rilevatore di gas

portatile / Przenośny wykrywacz gazu / Detector de gaz portabil

EN User manual ......................................................... 2

BG Ръководство за употреба ................................. 9

DE Benutzerhandbuch .............................................. 19

ES Manual de usuario ............................................... 29

FR Manuel utilisateur ............................................... 39

HU Használati utasítás .............................................. 49

IT Manuale utente .................................................. 59

NL Handleiding ........................................................ 69

PL Instrukcja obsługi ............................................... 79

RO Manual de utilizare ............................................. 89

Safety Information

Before using the device, please read this manual carefully and follow

the operation requirements as below:

Please don't use the defective detector. Before using, please check if

there is crack or spare parts’ missing. If there is, please contact the

seller.

It's suggested to do the "Impact Test" by following 4.2 before using this

device every day to check if the detector works well.

Only spare parts which are specified for JL269 or permitted by the

seller are allowed to be used.

Only the charger which is specified with JL269 is allowed to be used to

charge the device. It's forbidden to charge the device in dangerous

environment.

Please don't expose the device into the exceeding-range gas for long

time. Otherwise, it will seriously affect the performance or even damage

the device.

If exposed to the environment consisting of leaded compound,

sulfur-compound, organic phosphorus compound or silicon, the gas

sensor will be poisoned. Please don't use the device in the above

environment.

Please don't expose the device to the environment which consists of

H2S, hydrocarbons gas or high corrosive gas for long time. Otherwise,

it will restrain the response of the gas sensor and reduce the sensitivity.

If the device has to be used in the above environment, please carry out

the Impact Test before using it.

Please don't expose the device to the environment which has electric

shock, strong magnetic field or serious continuous mechanic shocking.

There is a NI-MH battery inside the device. Please don't place the

useless battery together with the rubbish. The useless batteries should be

discarded by qualified withdrawers.

Please change the rechargeable batteries if they have been used for 2

years or charged for 300 times.

It's forbidden to disassemble, adjust or repair the device without

permission.

Please avoid the device falling down from high place or serious

shocking.

Any other operation beyond this manual, please contact the seller.

1. Brief introduction

JL269 gas detector has a fast and stable performance and wide detecting

range. It can be used to detect methane, propane, natural gas, LPG, and

hydrogen gas, It will help you to find out the gas leakage sources easily.

Main function & features

Fast response, short warm-up time

Multi-level indicator lights

Long flexible gooseneck probe

Low voltage alert function

Automatic shut-off after under-voltage

Automatic zero point adjustment

2. Main technical Specifications

Target

gas

Sensor

type

Detecting range

CH4

semicondu

ctor

0～30000ppm （0～60%LEL ；0～

3.0%VOL）

C3H8

semicondu

ctor

0～20000ppm （0～95%LEL ；0～

2.0%VOL）

semicondu

ctor

0～10000ppm （0～25%LEL ；0～

1.0%VOL）

Sampling method: Natural diffusion

Response Time: ≤5s

Sensitivity: Better than 50ppm

Working condition: Temperature -10℃～55℃；

Humidity≤93%RH(no dews)

Storage condition: Temperature -30℃～60℃；

Humidity≤93%RH(no dews)

Indicator method: Multi stage lights indicate concentration, with variable

tunes and rhythms indication.

Power Source: 3.6V/1600mAh NI-MH rechargeable battery

Charging time: 4 to 7 hours

Working Time: >8h(working continuously in normal working status)

Sensor Life: 2 years

Dimensions: 180mm×72mm×36mm

Weight: About 300g

3. Structure and Functions

4. Operation

4.1 Power on

Press and hold “ ” for more than 2 seconds, the detector will power

on and enters into self-testing status. All LED lights will be lighted on and

then off alternately. At the same time, the buzzer and sensor start self-test.

After self-test, the sensor will proceed zero translation within 5 seconds, and

then the detector enters into detecting status. If sensor fault or zero

translation doesn’t finish within 5 seconds, please keep waiting. Check

“ OL” light. After it turns off, zero translation finishes and the detector

will enter into detecting status.

4.2 Impact Test

It is suggested to do Impact Test before using every day, so as to make

sure the detector work normally.

Test method:

After turning on the detector, put it into the gas with certain known

level or standard gas. If the display, alarm signal and buttons work normally,

then it can be carried out for detecting. If no response to the gas or

“ Fault” light is on, please contact the seller for solving the problem.

4.3 Detecting

Put the sensor (which is at the front end of flexible test bar) into the gas

environment. The quantity of LED lights and sound frequency will show the

gas concentration. With gas concentration increasing, first more and more

green LED lights will be turned on and the buzzer frequency increases.

When the concentration exceeds the green LED’s range, yellow LED lights

will be turned on, and then red LED lights. At the same time, the sound

frequency interval will turn higher. If the concentration reaches the highest of

the detection range, the “ OL” LED will light.

4.4 Battery voltage check

In detecting status, by pressing both and buttons, the user

can check how much voltage left in the battery. LED lights flash. The voltage

left is equal to the quantity of the LED lights. Press both and

buttons again, the detector will return to the detecting status.

Moreover, the user can also check the voltage by the color of

“ Power” light.

4.5 Open /

close audible

alarm

In detecting status, the initial setting of audible alarm is on. The more

gas leaks, the higher the audible alarm frequency will be. If the detecting

spot is too noisy, operator can use the earphone purchased by himself.

Press button can open or close the audible alarm function.

4.6 Set present level as reference basis

The gas concentration of the detection field is in gradient distribution.

In order to find the gas leakage source precisely, during detecting, the user

can set the present level as reference basis by pressing button.

4.7 Turn off the detector

Press both and buttons, the detector will be turned off.

5. Calibration

In order to assure the accuracy, it’s suggested to re-calibrate the detector

once every 6 months.

Calibration procedure:

Hold both and buttons to turn on the detector and the

detector will enters into calibration warm-up period. LED lights flash in

turns showing the warm-up period which will be about 3 minutes.

Color

Voltage

Green

Enough

Yellow

Not enough

Red

Low voltage, need charge

After warm-up finish, one green LED light will be lighted on, which

means the detector enters into zero calibration status. If the detector is in

clean air, press button to save the zero point information. Then,

“ Power” light is in green color and 3 green LED lights flash. Zero

calibration is done.

After zero calibration, one yellow LED will be lighted on which means

the detector enters into the calibration status of the second point. Put the

detector into the standard gas (level equals to the second point) and keep it

steady for about 30 seconds. Then press to save the second point

information. “ Power” light will be lighted on in yellow color, 3 green

LED and 3 yellow LED are lighted on and then flashing, which means the

calibration of second point is done. If there are more than two calibration

points, the operating method is same with the second point calibration.

After all points’ calibration finish, “ Power” light will be lighted in

green color and then turns off. The detector will turns off then.

Note:

There are more than two calibration points. Please carry out calibration

in order, first zero point calibration and then the second point, the third point.

During calibration, if the sensor responses abnormally, the “ Fault”

light and “ OL” light will be lighted on. Please note it.

6. Charging

Please charge the battery after the detector is turned off. The color of

“ Power” light on the charger will show the voltage level of the battery.

The charging will last for 4 to 7 hours. When “ Power” light doesn’t flash

and it is in green color, the charging is done. Please disconnect the charger

from the power source.

ChargingAttention

It’s forbidden to charge the detector in dangerous area. Otherwise, it

will damage the detector or cause fire & explosion.

During charging, it’s normal that the area around the battery will be

heated.

After the detector turns off automatically, please charge the battery

within 12 hours, so as to avoid that the battery cannot work due to too

voltage too much low.

If the detector won’t be used for a long time, please take out the

batteries and put it in dry environment.

During replacing the batteries, make sure they are with the same

capacity. If use alkaline batteries, please don’t charge them.

7. Sensor using and replacement

In normal working status, the sensor life is 2 years. When the sensor

is overdue or defective, please contact the seller for correct replacement

instruction.

8. Troubleshooting Guidance

Fault

Possible reason

Solution

Cannot be

turned on or auto

turn off

Too low voltage

Charge it in time or

replace the battery

No response to

gas

Warm-up or zero

calibration doesn’t finish

Wait till it finishes

Sensor fault

Replace the sensor

“ OL” is

Too high concentration

Make zero calibration

in the clean air or

re-calibrate the detector

Преносим детектор за газ

PNI JL269

Ръководство за употреба

ВНИМАНИЕ: Газовият сензор е консуматив и подлежи на гаранция

само за производствени дефекти!

БЕЛЕЖКИ ЗА БЕЗОПАСНОСТ

Не се опитвайте да използвате детектора, ако има пукнатини или

липсва някоя съставна част

Извършете тестовата процедура, преди да използвате детектора, за

да се уверите, че работи правилно

Поддръжката и ремонтът на уреда се извършват само в оторизирани

сервизи. Моля, свържете се с доставчика, ако устройството не

работи правилно

Използвайте само зарядното устройство в опаковката за зареждане

на батерията

Не излагайте детектора на висока концентрация на газ за дълги

периоди от време, за да запазите целостта на сензора и работата на

детектора

Не използвайте детектора в среда, богата на метални съединения,

сулфити, силикон или органични фосфорни съединения, за да не

отровите сензора

Не използвайте детектора в рамките на електромагнитни полета

Вътре в устройството има батерия тип NI-MH. Ако трябва да бъде

изхвърлен, консултирайте се с местните правила за събиране

Батерията има жизнен цикъл от 2 години или 300 презареждания.

След този период сменете батерията с нова

Батерията не трябва да се съхранява или използва в близост до огън,

източници на топлина или в среда с висока температура, за да се

избегнат течове, прегряване, пожари или дори експлозии.

Ако батерията изтича, излъчва странна миризма, прегрява, променя

цвета си или се деформира по време на употреба, зареждане или

съхранение, спрете да я използвате незабавно

Избягвайте да удряте или изпускате устройството

Inhaltsverzeichnis

Sprachen:

Andere PNI Gaswarngerät Handbücher

PNI

PNI SAFE HOUSE 200 Bedienungsanleitung

PNI

PNI Safe House Dual Gas 250LR Bedienungsanleitung

PNI

PNI SafeHouse HS110 Bedienungsanleitung

PNI

PNI SafeHouse HS110 Bedienungsanleitung

PNI

PNI SAFE HOUSE 200 Bedienungsanleitung

PNI

PNI Safe House Smart Gas 300 WiFi Bedienungsanleitung

PNI

PNI GD-01 Bedienungsanleitung

PNI

PNI GD-01 Bedienungsanleitung

PNI

PNI GD-01 Bedienungsanleitung

PNI

PNI GD-01 Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung

MSA

MSA ULTIMA X5000 Bedienungsanleitung