Polaris Q4000 Bedienungsanleitung

OWNER’S MANUAL

English |Français |Español

H0783100_REVA

Works with Polaris Booster Pump

Fonctionne avec un surpresseur

Funciona con bomba de presión adicional

English

To avoid risk of potentially serious injury:

• Do not handle the Polaris cleaner while it is operating, except when checking the wheel RPM.

• Always remove the Polaris cleaner before swimmers enter the pool.

CAUTION

WARNING

USE OF A POLARIS Q4000 IN A VINYL LINER POOL

Certain vinyl liner patterns are particularly susceptible to rapid surface wear or pattern removal caused by

objects coming into contact with the vinyl surface, including pool brushes, pool toys, oats, fountains, chlorine

dispensers, and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded

simply by rubbing the surface with a pool brush. Ink from the pattern can also rub off during the installation

process or when it comes into contact with objects in the pool. Zodiac Pool Systems LLC and its afliates and

subsidiaries are not responsible for, and the Limited Warranty does not cover, pattern removal, abrasion or

markings on vinyl liners.

original instructions

English

For customer service or support:

Zodiac Pool Systems Canada, Inc.

2-3365 Mainway

Burlington, ON L7M 1A6

1.800.822.7933 | PolarisPool.ca

Zodiac Pool Systems LLC

2882 Whiptail Loop # 100

Carlsbad, CA 92010

1.800.822.7933 | PolarisPool.com

Zodiac Pool Care Europe

ZA de la Balme - BP 42

31450 Belberaud FRANCE

PolarisPool.eu

Fluidra Group Australia Pty Ltd

PO Box 7238, Wetherill Park NSW 2164

ABN: 87 002 641 965

1300 763 021 | PolarisPool.com.au

Fluidra NZ Ltd

13 Douglas Alexander Parade

Rosedale, Auckland 0632

NZBN: 942 903 181 70759

0800 807 665 | Fluidra.co.nz

• Before installing the Polaris®cleaner, make sure the pool filter is clean.

• New plumbing lines should be flushed out before installing the cleaner.

• The cleaner should not be used to remove plaster dust in new pools.

• Except when checking the wheel RPM, do not handle the cleaner while it is operating.

• Always remove the cleaner before swimmers enter the pool.

• Disconnect the cleaner from the pool wall when cleaning or backwashing the pool filter.

• Always remove the cleaner from the pool before chemical shock treatments.

• After cleaning or backwashing, let the filtration system run for at least five minutes before

re-connecting the cleaner.

Before You Start: Important Information

English

a - Cleaner Body

b - Filter Canister - All-Purpose Debris

c - Hose Assembly

d - In-Line Filter Assembly

e - Quick Disconnect

f - Pressure Relief Valve

g - Universal Wall Fitting (UWF

)

h - Retrictor Disks (Blue and Red)

i - Hose Nuts

j - Feed Hose Connector

k - Hose Floats

l - Hose Swivels

Included in the Box

in bag

blue

red

Installed in cleaner

English

Read the complete owner’s

manual before you begin installation.

1 Prepare the Pool

1. Turn on the filtration pump, allow to prime.

2. Turn on the booster pump and flush plumbing lines for five minutes.

3. Turn off both pumps.

2 Install the Universal Wall Fitting

The UWF installs on pools with a dedicated cleaner return line and a threaded 1-1/2”

female pipe fitting.

1. Remove the Universal Wall Fitting (UWF) (g) from the Quick Disconnect (e).

2. Thread the UWF (g) with Blue Restrictor Disk (h) in place, into the dedicated

cleaner return line.

3. Attach the Quick Disconnect (e) and hose to the UWF (g). Turn clockwise then

pull away to secure.

Cleaner return line

Buse de refoulement de la piscine

línea de retorno para el limpiador

dedicated cleaner

return line

English

3 Adjust Hose Length

1. With the hose assembly (c) connected at the cleaner return line, extend

the

end of the hose to the farthest point of the pool. Do not include steps or

seating areas.

2. The end of the hose should be within 6″ (15 cm), longer or shorter, of

farthest point.

• If hose is too short, add a feed hose section with floats, a swivel and two

hose nuts, available through your local Polaris dealer. Adjust to proper

length.

3. Cut the hose so that it is within 6” (15 cm) of the farthest point.

Cut to within 6” (15 cm) of the farthest point

Couper à 15 cm du point le plus éloigné

Corte a 15 cm del punto más lejano

Walk hose around to

determine farthest point.

English

1-3'

(30-90 cm)

1-3'

(30-90 cm) 1-3'

(30-90 cm)

1-3'

(30-90 cm)

4 Connect Hose Fitting and Adjust Floats

1. Place the hose nut (i) onto the end of the feed hose connector (j).

2. Push the hose assembly (c) onto the feed hose connector (j).

Water can be used to lubricate the hose.

• Tightly secure the hose nut (i) onto the hose assembly (c).

3. Position the first hose float (k) up against the feed hose connector (j) and then space

hose floats 1-3 ft (30-90 cm) apart.

English

5 Assemble the Cleaner

WARNING

To avoid risk of potentially serious injury, do not swim or use the pool

when the cleaner is submerged or operating.

1. Attach the feed hose connector (j) to the cleaner.

2. Confirm the first hose float (k) is up against the feed hose connector (j).

3. Submerge the cleaner, allow it to sink to the bottom of the pool.

English

6 Check for Proper Wheel RPM

Before operating the cleaner, check for proper wheel revolutions per minute (RPM). For

maximum efficiency, the cleaner should operate between 28 and 32 RPM.

IMPORTANT: Keep the cleaner submerged for accurate wheel speed count.

1. Turn on the filtration pump and allow it to prime.

2. Turn on the booster pump, the cleaner will begin to move.

3. With both pumps on, pull the cleaner to the waterline and keep submerged.

CAUTION: Always lift the cleaner using the handle and take care to avoid possible

hair entanglement when leaning over.

NOTE: The Polaris®logo latch is not a handle.

4. Using the Polaris logo on the left-front wheel as a reference, count wheel

revolutions (RPM) for 1 minute. If wheels change direction during timing, start over.

5. Target wheel speed is 28 to 32 RPM. If wheel speed is not in target range, refer to

Section 7 Adjust Wheel Speed.

1 min.

28-32

RPM

Keep cleaner

submerged for accurate

wheel speed count.

English

7 Adjust the Wheel Speed

< 28 RPM

• Check the filter screen in the in-line filter

assembly (d) for debris that restricts

water flow.

• Clean the skimmer, filter, and pump

basket, clearing debris that restricts

water flow.

• Check the hoses and connections

for leaks that cause loss of water

pressure.

• Check hose swivels (l) for for

excessive leaking or spraying.

Verify flow direction arrow ( ) is

toward the cleaner.

• Remove the blue restrictor disk (h)

from the UWF®(g).

> 32 RPM

• Replace the blue restrictor disk with

the red restrictor disk (h).

• Loosen the pressure relief valve (f)

until proper RPM is reached.

NOTE: The Pressure Relief Valve

should only be adjusted when a

restrictor disk is installed.

red

rouge

rojo

Flow direction

arrow ( )

toward

the cleaner

Inhaltsverzeichnis

Sprachen:

Andere Polaris Schwimmbadroboter Handbücher

Polaris

Polaris Quattro Tune-up Kit Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Original Betriebsanleitung

Polaris

Polaris Vac-Sweep 360 Bedienungsanleitung

Polaris

Polaris Maxx Bedienungsanleitung

Polaris

Polaris Vac-Sweep 165 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Bedienungsanleitung

Polaris

Polaris 8050 Sport Bedienungsanleitung

Polaris

Polaris 3900 Sport Bedienungsanleitung

Polaris

Polaris Vac-Sweep 180 Bedienungsanleitung

Polaris

Polaris 3900 Sport Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Bedienungsanleitung

Polaris

Polaris 340 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Bedienungsanleitung

Polaris

Polaris 9350 Bedienungsanleitung

Polaris

Polaris 9500 Sport Bedienungsanleitung

Polaris

Polaris Vac-Sweep 65 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 360 Bedienungsanleitung

Polaris

Polaris Alpha iQ+ Bedienungsanleitung

Polaris

Polaris Quattro Bedienungsanleitung

Polaris

Polaris robotic NEO EM27 Series Bedienungsanleitung

Polaris

Polaris 380/P38 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Polaris

Polaris 9350 Sport Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

Zodiac

Zodiac Baracuda G3 Bedienungsanleitung