Polycom RealPresence EduCart 500 Second Bedienungsanleitung

www.polycom.com

Polycom, Inc. and are registered and/or common law marks in the United States and various other countries. No portion hereof may be reproduced

or transmitted in any form or by any means, for any purpose other than the recipient’s personal use, without the express written permission of Polycom.

Polycom, Inc.

6001 America Center Drive

San Jose, CA 95002, USA

1725-65640-001/A

Set Up the Polycom® RealPresence®

EduCartTM 500 Second Display Option

Flat Screen Display

Note that your display may

look diﬀerent than the display

shown in this document.

Base with

Locking Wheels

“Grab”

Handles

Basket

H Frame

Poles

Back

Cover

Set Up the Polycom® RealPresence® EduCartTM 500 Second Display Option 2

1Place the base on the ﬂoor and lock the wheels.

Insert each pole into the base with the threaded

inserts lined up with the holes at the rear of the

base. Loosely insert two 3/8” bolts with ﬂat washers

on the back side and one in the bottom of each pole.

Tighten with a 9/16” wrench.

Remove the basket and basket bracket from the

H frame by removing the two screws circled in

red.

Remove the display from packaging. If possible,

leave the display on the bottom portion of the

packaging. Using four long M8 x 25 screws and

spacers between the H frame and the dislay, attach

the H frame to the rear of the display using the

holes indicated below. If the packaging interferes,

either cut the foam or lift the display out.

4Insert four M8 x 16 screws on the back of the frame

and hand tighten to about half way. The screws

must be loose to ﬁt onto the cart.

If this system is not used with a Polycom-

supplied display, the display used must have

VESA 400 mm x 400 mm or 400 mm x 600 mm

mounting and must not exceed any of the

following parameters:

Diagonal size: 55” (1400 mm)

Depth: 2.6” (65 mm)

Weight: 66.1 lbs (30 kg)

Note that some displays require M6 screws

that are not supplied.

Set Up the Polycom® RealPresence® EduCartTM 500 Second Display Option 3

Adjust the handles by loosening the two screws

on each bar (four screws per side). Extend the

handle at or beyond the display by 1-2”. Replace

the screws and tighten. Use the same hole in the

series of holes on both sides. These handles will be

used to move the cart.

Ensure that the cart casters are locked. With a

person on each side, lift the display, by the handles,

onto the cart at the desired height. Ensure that

all four M8 screws installed in step 6 are hooked

into the keyhole slots in the cart poles. Tighten the

four M8 screws through the holes.

8Attach the storage basket to the bottom of the H

bracket under the power bar using the two screws

removed in step 2.

Attach the vanity plate on the front of

the cart between the speakers.

Set Up the Polycom® RealPresence® EduCartTM 500 Second Display Option 4

Install the magnetic back cover over the codec and

cables and fasten with the two supplied screws.

Attach and route the cables. Run the power cord

from the power bar, down the adjacent pole, and

exit the cord end at the hole at the bottom of the

pole. Run the supplied HDMI extension cable the

same way. Store excess cable with the cable wrap

bracket at the bottom of the cart base.Refer to the

wiring diagram at the end of this document for

details.

Only EduCart 500 components should be

plugged into the power outlet block. Do not

power any other electrical equipment from this

power outlet.

Set Up the Polycom® RealPresence® EduCartTM 500 Second Display Option 5

Child Safety Warnings:

Death or serious injury may occur when children climb on

audio and/or video equipment furniture. A remote control or

toys placed on the furnishing may encourage a child to climb

on the furnishing and as a result the furnishing may tip over

onto the child.

Relocating audio and/or video equipment to furniture not

speciﬁcally designed to support audio and/or video

equipment may result in death or serious injury due to

furniture collapsing or overturning onto a child.

Mains Input Rating:

Voltage: 100-240 VAC, 50/60Hz

Current: 3.4A (max)

Weight:

Assembled System: 122 lbs (55 Kgs)

Sampo 55” LED Display (Model PME55MA):

66.1 lbs (30 Kgs)

Note that weights are subject to change.

Regulatory Notices and General Warnings:

This equipment is intended for indoor use only.

This equipment is intended to be suitable for institutional use.

Do not use a power cord that is damaged. This could cause

ﬁre or electric shock. Contact the manufacturer for a

replacement cord, if necessary.

Only use a power cord which is appropriately rated and

approved relevant to the country of use.

This equipment should be used only on even surfaces.

This equipment has lockable wheels which should be

applied while the cart is stationary.

When connecting to the mains supply, connect only to an

earthed supply outlet which is installed near the equipment

and is easily accessible.

Keep ventilation openings free from any obstructions.

The ambient operating temperature rating of this equipment

is 0 - 40ºC and should not be exceeded.

Do not immerse the system in any liquid or place any liquids

on it.

Do not spray liquids directly onto the system when cleaning.

Always apply the liquid ﬁrst to a static-free cloth.

For further information concerning the individual components

of this equipment, please refer to the respective product

literature.

For support or service, please contact your Polycom®

distributor or go to Polycom Support at

www.polycom.com/support.

Set Up the Polycom® RealPresence® EduCartTM 500 Second Display Option 6

EduCart 500 Wiring Diagram

Inhaltsverzeichnis

Andere Polycom Konferenzsystem Handbücher

Polycom

Polycom VSX 3000 Service-Handbuch

Polycom

Polycom RMX 1000 Bedienungsanleitung

Polycom

Polycom iPower 900 Series Bedienungsanleitung

Polycom

Polycom QDX 6000 System Service-Handbuch

Polycom

Polycom SoundStation IP 7000 Bedienungsanleitung

Polycom

Polycom QSX Abmessungen

Polycom

Polycom RMX 1000 Bedienungsanleitung

Polycom

Polycom HDX Desktop Systems Bedienungsanleitung

Polycom

Polycom EagleEye Handbuch

Polycom

Polycom RMX 1000 Datenblatt

Polycom

Polycom HDX Series Bedienungsanleitung

Polycom

Polycom RealPresence Practitioner Cart 8000 Bedienungsanleitung

Polycom

Polycom SoundStructure Systems Bedienungsanleitung

Polycom

Polycom RealPresence Group 500 systems Gebrauchsanweisung

Polycom

Polycom QDX 6000 System Bedienungsanleitung

Polycom

Polycom realpresence 1800 Service-Handbuch

Polycom

Polycom RealPresence RMX 4000 Montageanleitung

Polycom

Polycom VIEWSTATION EX Bedienungsanleitung

Polycom

Polycom RealPresence Centro Handbuch

Polycom

Polycom ReadiRecorder Bedienungsanleitung

Polycom

Polycom realpresence trio 8800 Bedienungsanleitung

Polycom

Polycom ViewStation vsx7000 Bedienungsanleitung

Polycom

Polycom Studio P009 Bedienungsanleitung

Polycom

Polycom VBP 7301 Handbuch

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Inmarsat

Inmarsat mini M Bedienungsanleitung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung