Polycom KIRK IP Bedienungsanleitung

Polycom®

KIRK IP Interface Card - User Guide

1. Introduction

This guide helps you setting up the KIRK Wireless Server 1500 with IP Interface Card on a Cisco CallManager.

Please refer to your CallManager user manual for general information.

2. Installation

1. Power down the WMS (Wireless Mobility Server).

2. Remove the top cover by unscrewing the screws on both sides of the WMS and the screws at the rear panel.

3. Remove the blind cover plate in front of the slot

closest to the power supply (please refer to the

figure at right).

4. Insert the KIRK IP Interface Card into the slot 0

(see drawing) and mount the two screws from the

blind cover.

5. Put back the top cover.

6. Connect an RJ45 cable (not included) between the

KIRK IP Interface Card on the back of the WMS

and the LAN network.

7. Power up the WMS again.

8. Verify that the LED’s are flashing as follows:

Active

In HTTP mode and when packets are transmitted on the Ethernet the Active LED is turned on.

100

In HTTP mode and when the Ethernet speed is 100mbps the 100 LED is turned on. When 10mbps Ethernet is

connected it will be off. ‘

Link

When the Ethernet link layer is established the Link LED is turned on.

Ready

When the system is running and ready the Ready LED is turned on. If the system is not ready the LED will start

flashing. In TFTP mode the Ready LED is flashing and all other LED’s are off.

Front LED

The front LED is green when the system is running and the subscriptions are read.

Software and help files are available at: http://www.kirktelecom.com/Installers/suk227.asp

3. IP Addresses

The KIRK IP Interface Card is configured with the IP address: 192.168.0.1 as a standard. This address has to be

changed for customizing the sub-net mask of the network. Start configuring the PC to the IP system’s identical net

mask, e.g. the address: 192.168.0.2 and sub-net mask: 255.255.255.0. The system is now ready to be reached with a

standard internet browser.

To change the address in the card to e.g. 10.1.1.150 please follow the steps below:

1. Start an Internet browser and address the card with IP

address 192.168.0.1

2. Select Gateway -> Config (user = admin, password =

ip1500)

3. Select IP Interfaces -> Ethernet Interface in the pop up

window

4. It is now possible to change the IP address of the card

and the IP address mask. Type the new IP address in

the ”IP address” field and press save -> activate.

5. Type the default router if applicable

6. No other fields are supported

7. Select IP Interfaces

8. Type off service must be set to 0xb8, and press save ->

activate.

4. Configuring the KIRK IP Interface Card to the

CallManager

1. Start an internet browser and address the card

2. Select Gateway -> Config (user = admin, password =

ip1500)

3. Select DECT Interface -> GW-DECT

4. Set protocol to “Skinny”

5. Type the IP address of the Gatekeeper. (Primary Call

Manager IP)

6. Type the IP address of the alternate Gatekeeper.

(Secondary Call Manager IP)

7. Type DECT1 in HW ID

8. Check the “enable user directory” box

9. Press Save -> Activate

10. No other fields are supported.

5. Registration of Users on the CallManager

Users have to be registered on the CallManager as well as on the KIRK IP Interface Card. Please follow the steps

below to register users on the CallManager:

1. Start the CallManager software

2. Select "Device” -> ”phone”

3. Select ”add a new phone”

4. In the field “phone type” select “Cisco 7940” and press next

5. Type i.e. the handset serial number (without space) in the field ”MAC address”

6. Type a description of the handset in the field ”description”

7. Select ”Default” in device pool and press ”insert”

8. Type the extension number in the field ”directory number” and press ”insert”

9. Ensure that call waiting is turned off for all DECT Phones

10. Please note that the wireless system supports automatic registration

6. Subscription of Users on the KIRK IP

Interface Card

How to register users on the IP card:

1. Open the IP Interface Card with an internet

browser

2. Select Gateway -> users -> new user

Name: some name you choose

Nickname: Prefix “SEP” and then the IPEI number

(without spaces), i.e. SEP000770669569. This number

must be the same as the one given in the Call

Manager

Number: The extension you choose for the phone. The number must be unique, e.g. 320

Display: The stand-by display text of the handset

IPEI: The IPEI number of the handset is located in the battery casing of the handset. If the battery compartment is

not accessible i.e. on newer KIRK handsets, the IPEI number can be seen in the display by typing *99984* ENTER (v).

AC (access code) optional: An access code can be defined for the handset login procedure.

Password: Not supported

7. Subscription of Handsets

Before registering handsets on the system, the system

must be set to “subscription allowed”. The

subscription setting can be changed in the info menu.

1. From the handset choose the SUBSCRIPTION

CREATE menu to subscribe to the new system.

Use the < and > keys to scroll between the Id’s of

the different systems if there are more than one

system available. If the handset is already

subscribed to 10 systems you will need to remove

one of the existing subscriptions.

2. Choose the system that you wish to subscribe to.

When a subscription is available, enter the free

system using < or > and the AC if required.

3. If the subscription was successful, the standby text

and the speaker icon is shown in the display. If

not, the subscription has failed and the procedure

must be repeated.

4. For re-subscription of a DECT handset that has

previously been subscribed to the CallManager, it

may be necessary to reset the handset from the

CallManager after subscribing the handset.

Please refer to the KIRK 3040 handset user guide for further reference.

8. Remove a Subscription from the System

If you wish to remove a subscription from the system, it is very important that the subscription is removed FIRST on

the KIRK IP Interface Card and then on the Call Manager.

9. Firmware Upload

It is possible to upload new firmware to the system. Download the newest firmware from www.kirktelecom.com.

Choose “firmware update” from the menu and locate the *.bin file. Do not interrupt the system while the firmware is

being uploaded. The system needs to be restarted for the new firmware to function properly.

10. Pre Call Services

Activate Call-Forward-All:

Use this feature to send all calls from one telephone number to another telephone number. To activate Call-

Forward-All, follow these steps:

Procedure

Step 1 Press the hook key, and dial ** then 1 on your telephone keypad. You will receive a confirmation tone.

Step 2 Enter the telephone number to which you want to send the calls. A confirmation tone will sound.

Step 3 Hang up.

Cancel Call-Forward-All:

To cancel Call-Forward-All, follow these steps:

Procedure

Step 1 Press the hook key, and dial ** then 2 on your telephone keypad. You will receive a confirmation tone.

Step 2 Hang up.

Call Pickup:

(NOT SUPPORTED FOR SRST)

To answer a phone in your call pickup group, follow these steps:

Procedure

Step 1 Press the hook key, and dial ** then 3 on your telephone keypad.

10. Note

Cisco charges users of the CallManager software a license fee for each IP Phone, soft phone or other endpoint system

(“IP Phone”) that connects into the Cisco CallManager software. This CallManager user license fee applies regardless

of the source (Cisco, Licensee or a third party) or the functionality of that IP phone.

Licensee must communicate to Licensee’s field, channels and customers, in a form and manner approved in advance

by Cisco, the following information about the program: How to make payment of that CallManager User License Fee

under a particular part ID number. (URL to be provided to Licensee by Cisco or customers may contact their Cisco

Field representative to make payment).

14184602, Ed. 1

Inhaltsverzeichnis

Andere Polycom Netzwerkkarte Handbücher

Polycom

Polycom KIRK ISDN Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Hama

Hama 49276 Bedienungsanleitung

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung