Power Tec 92489 Bedienungsanleitung
Our products are designed to be used correctly and with care for the purpose
for which they are intended. No liability is accepted by the Tool Connection for
incorrect use of any of our products, and the Tool Connection cannot be held
responsible for any damage to personnel, property or equipment when using the
tools. Incorrect use will also invalidate the warranty.
If applicable, the applications database and any instructional information provided
has been designed to offer general guidance for a particular tool’s use and while
all attention is given to the accuracy of the data no project should be attempted
without referring first to the manufacturer’s technical documentation (workshop or
instruction manual) or the use of a recognised authority such as Autodata.
It is our policy to continually improve our products and thus we reserve the right to
alter specifications and components without prior notice. It is the responsibility of
the user to ensure the suitability of the tools and information prior to their use.
• Wear eye and hand protection when using this tool kit.
• Always carefully clean the tool components after each use.
• Keep the tool components safe and tidy in the supplied case.
• Do not use the kit for any purpose other than for which it is designed.
Safety Warnings - please read
www.toolconnection.co.uk
Part No. 92489
Parking Distance Sensors
Hole Cutter Set
Instructions
www.toolconnection.co.uk
92489_Instructions_V3
2
www.toolconnection.co.uk
7
3
www.toolconnection.co.uk
Components
Introduction
This kit is designed for the operator to cut clean, accurately sized holes for PDC (Park
Distance Control) sensors, for example, when fitting a new replacement bumper panel after
accident damage. The kit includes a drill for the pilot hole plus hole punches for ten common
sizes of PDC sensor holes: 17, 18, 18.2, 19, 20, 22.5, 24, 26, 26.7 and 32mm. Will cut
through plastic up to 5mm in thickness.
Precautions:
• Refer to the manufacturer’s documentation and PDC fitting instructions to determine the
exact size and location of the hole for the PDC to be fitted.
• Be aware that facelift models may have the PDC units fitted in different locations; again,
refer to the manufacturer’s documentation for the location of the holes to be punched out
(some bumper panels have location markings on the inner surface).
A HSS Drill Bit Ø 5/16" (8.0mm)
B Force Screw Assembly
C Reaction Plates
D Hole Dies
E Hole Punches
7. When the punch breaks through the material, unscrew the assembly,
then withdraw the hole punch from the bumper panel (Figure 7), leaving
a cleanly cut hole.
Instructions
Figure 7
Our products are designed to be used correctly and with care for the
purpose for which they are intended. No liability is accepted by Power-TEC
for incorrect use of any of our products, and Power-TEC cannot be held
responsible for any damage to personnel, property or equipment when
using the tools. Incorrect use will also invalidate the warranty.
Precautions
www.toolconnection.co.uk
6
1. Refer to the manufacturer’s documentation and PDC fitting instructions
to determine the locations and exact size of the hole for the PDCs to
be fitted (some bumper panels have location markings on the inner
surface).
2. Drill pilot hole: refer to Figure 2: use the supplied drill bit (A) to drill
through the centre of the marked location position. Wear eye protection
when drilling.
3. The five sets of reaction plates (C), dies (D) and punches (E) supplied will
enable ten different hole sizes to be punched. Once the diameter of the
hole has been decided, choose the correct reaction plate, die and punch
for the specified hole size.
Instructions
C D
B
E
www.toolconnection.co.uk
4
4. Assemble these components through the pilot hole as shown in either
Figure 3 or 4. Refer to the markings on the die and punch; ensure that
the desired hole size dimensions are facing each other, for example for a
26mm hole, the 26mm die faces the 26mm punch; for a 32mm hole, the
32mm die faces the 32mm punch, etc.
5. Refer to Figure 5: on the inner surface of the panel use a 12mm socket
or spanner to hold the force screw steady.
6. Refer to Figure 6: use a 12mm socket or spanner and tighten force
screw nut clockwise to force the hole punch through the bumper panel
material.
Instructions
Outer surface of panel
www.toolconnection.co.uk
5
Andere Power Tec Rack & Stand Handbücher
Power Tec
Power Tec 71699 Bedienungsanleitung
Power Tec
Power Tec MT4005 Bedienungsanleitung
Power Tec
Power Tec MT4002 Bedienungsanleitung
Power Tec
Power Tec MT4008 Bedienungsanleitung
Power Tec
Power Tec MT4000 Bedienungsanleitung
Power Tec
Power Tec MT4004 Bedienungsanleitung
Power Tec
Power Tec 71703 Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
