Powercom 800VA Bedienungsanleitung

UPS

Uninterruptible Power System

500VA/ 650VA/ 800VA

User’s Manual

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

●WARNING (SAVE THESE INSTRUCTIONS): This manual contains important instructions

that should be followed during installation and maintenance of the UPS and batteries.

●WARNING (Controlled Environment) : Intend for installation in a controlled environment.

●CAUTION: Do not dispose of batteries in a fire, the battery may explode.

●CAUTION: Do not open or mutilate the battery, released electrolyte is harmful to the skin

and eyes. It may be toxic.

●CAUTION: A battery can present a risk of electric shock and high short circuit current. The

following precaution should be observed when working on batteries

Remove watches, rings or other metal objects.

Use tools with insulated handles.

Wear rubber gloves and boots.

Do not lay tools or metal parts on top of batteries.

Disconnect charging source prior to connecting or disconnecting battery terminals.

●Servicing of batteries should be performed or supervised by personnel knowledgeable of

batteries and the required precautions. Keep unauthorized personnel away from batteries.

●When replacing battery, replace with same type.

●Do not to addition battery for UPS.

TABLE OF CONTENTS

INTRODUCTION………………………………………………………….……………………………..1

IMPORTANT SAFETY INSTRUCTIONS………………………………………………………..………1

1. PRESENTATION………………...………….……………………………..…,.………………………2

2. INSTALLATION….………………………………………………………...…………………………3

3. OPERATION………………………………………………………………...………………………3

4. ALARMS………………………….….…………………………………………..……………………3

5. SOFTWARE AND INTERFACE PORT…………………………………………………………………4

APPENDIX A TROUBLESHOOTING……………………………………...……………..…………………5

APPENDIX B SPECIFICATIONS……..…………………………………...……………..………………5

Please read and save this manual !

Thank you for selecting this uninterruptible power system (UPS). It provides you with a

perfect protection for connected equipment. The manual is a guide to install and use the

UPS. It includes important safety instructions for operation and correct installation of the UPS.

If you should have any problems with the UPS, please refer to this manual before calling

customer service.

1. PRESENTATION

The UPS is a standby uninterruptible power system (UPS). When utility input is normal, the

UPS would provide surge protection and energy to charge the internal battery. If the utility

input is abnormal, the UPS can supply AC power to the load immediately.

(1). Utilizes microprocessor based controls, it will minimizes the dependency on hardware.

Beside this, it maximizes system flexibility and optimizes the assurance of reliability.

(2). Automatic frequency selection to match with utility power.

(3). Hi-grade battery charger to prolong battery’s life and fully charge the battery.

(4). With actual overload protection both in line and battery mode.

Front View

1.1 “POWER” indicator (Green): The indicator will illuminate

when the utility input is normal.

The light becomes flash when working at back-up mode.

1.2 “OVERLOAD” indicator (Red): The indicator will

illuminate when the output power is overload from the unit.

1.3 “BATTY” indicator (Red): The indicator

illuminates when the battery is no longer useful and must

be replaced.

1.4 “ON/OFF/TEST” button: No matter the UPS is

plugged in or not. Press the “ON/OFF/TEST”

button till the beep stop to turn on or turn off the UPS.

It also enables the UPS self-test by press the bottom less

than 1 second.

1.5 “BUZZER STOP” button

In back up mode, press the bottom about 1 second to

enable the UPS silence function.

RearView

1.6 Outlet Socket

1.7 Communication Port*

1.8 Internet/Tel/Modem Port*

1.9 Bypass Outlet (U.S. socket only)

1.10 Input Fuse

1.11 AC Input

*Can be removed if not desired

POWER

OVER LOAD

BATT CHECK

ON/OFF/TEST

BAZZER STOP

2. INSTALLATION

2.1 Inspection: Inspect the UPS upon receipt. The packaging is recyclable; save it for reuse

or dispose of it properly.

2.2 Placement: Install the UPS in controlled area with adequate air flowing and free of

excessive dust. Do not operate the UPS at outdoor area.

2.3 Utility Power: The input power cord needs to connect the rear inlet socket of the UPS

and plug into a socket on the wall. Please notice the voltage of utility power should match

with the UPS. (For example, the rating voltage of UPS is 110V/(220V), the input utility power

should be the same as 110V/(220V) .)

2.4 Connection: The employed equipment’s power cords (such as computer) are plugged

into the sockets on the rear panel.

Attention: Service personnel installable.

Attention: With the installation, the overall leakage current of the UPS connected consumer

shall not exceed 3.5mA.

Attention: A block diagram of this unit is attached to the user’s manual and to the installation

instruction.

3. OPERATION

3.1 Switch on: When utility input is connected to the UPS, press “ON” button at “OFF” mode

and keep pressing until the beep stops. After that, connect the electrical cords of the

equipment that is going to be used such as computer or monitor with the terminal at the rear

panel of UPS.

Attention: This unit is to operate by any individuals with previous training.

Attention: At “BACKUP” mode, UPS can be automatically turned off if none of the

connected loads is operating. (No Load shut down function)

CAUTION: Never connect a laser printer or plotter to the UPS with other computer

equipment. A laser printer or plotter periodically draws significantly more power than its idle

status, and may overload the UPS.

3.2 Switch off: Press the “OFF” button at “LINE” or “BACKUP” modes and keep pressing

more than 1 second to turn off the UPS.

3.3 Silence: When UPS is under “BACKUP” mode, press the “BUZZER STOP” button about

1 second to silence the audible alarm. (The function is disabled when UPS is under

condition of “LOW BATTERY” or “OVERLOAD”)

3.4 Self-test function: Press the “TEST” button at “LINE” mode about 1 second, UPS will

perform self-test procedure automatically.

4. ALARM

4.1 “BACKUP” (slow alarm): When the UPS is working under “BACKUP” mode, the UPS

would emit audible alarm. The alarm stops when the UPS is return to “LINE” mode

operation.

Attention: The alarm of “BACKUP” is going to beep every 2 seconds. (Slow-speed beep).

Attention: The UPS provides mute function for the warning. When the beeping sound

occurs, press "BUZZER STOP" to stop it; and press "BUZZER STOP" again to resume

the sound.

4.2 “LOW BATTERY” (rapid alarm): In the “BACKUP” mode, when the energy of battery

becomes to lower level. (about 20%~30%) The UPS beeps rapidly until the UPS shuts down

from battery exhaustion or returns to “LINE” mode operation.

Attention: The alarm of the batteries caused by low voltage beeps every 0.5 second.

Attention: The rapid alarm under “LOW BATTERY” condition cannot be muted.

4.3 “OVER LOAD” (continuous alarm): When the UPS is working under overload

condition (the connected loads exceed the maximum rated capacity), the UPS will emit

continuous alarm to warn an overload condition. In order to protect the unit and the loads,

the UPS will be automatic turn off. Please disconnect nonessential devices from UPS to

eliminate the overload alarm.

5. SOFTWARE AND INTERFACE PORT

5.1 Power Monitoring Software

The UPS-MON series software (or other power monitoring software) is applied standard

RS-232 interface to perform monitoring functions, and then provides an orderly shutdown of

a computer in the event of power failure. Moreover, UPS-MON displays all the diagnostic

symptoms on monitor, such as Voltage, Frequency, Battery level and so on. The software is

available for DOS, Windows 3.1x, Windows 95, Windows 98, Windows NT V3.5 or later,

Novell Netware, Linux, and others. Call your dealer for more information on computer OS

compatible solutions.

5.2 Interface Kits

A series of interface kits is available for operation systems that provide UPS monitoring.

Each interface kit includes the special interface cable required to convert status signals from

the UPS into signals which individual operating system recognizes. The interface cable at

UPS side must be connected to REMOTE PORT, at computer side can be either COM 1 or

COM 2. The other installation instructions and powerful features please refer to READ.ME

file.

CAUTION: Use only factory supplied or authorized UPS monitoring cable!

5.3 The characteristics of computer interface port

The computer interface port has the following characteristics:

The communication port on the back of the UPS may be connected to host computer. This

port allows the computer to monitor the status of the UPS and control the operation of the

UPS in some cases. Its major functions normally include some or all of the following:

To broadcast a warning when power fails.

To close any open file before the battery is exhausted.

To turn-off the UPS.

Some computers are equipped with a special connector to link with the communication port.

In addition, special plug-in cord may be needed. Some computers may need special UPS

monitoring software. Contact your dealer for the details on the various interface Kits.

APPENDIX A TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE ACTION TO TAKE

ON/OFF/TEST/SILENCE button

not pushed or push-time too

short

Press the

ON/OFF/TEST/SILENCE button

more than 1 second

Battery voltage less than 10V Recharge the ups at least 6 hours

PCB failure Replace the PCB, call for service

UPS cannot turn

LED not light

Load less than 20W at battery

mode

Normal condition, “No load

shutdown function” is active.

Power cord lose Plug in the power cord

AC FUSE burn out Replace the AC fuse

Line voltage too high, too low or

black out

Normal condition

UPS always at

battery mode

PCB failure Replace PCB, call for service

battery not fully charged Recharge the UPS at least 6

hours

Back up time too

short

PCB failure Replace PCB, call for service

Buzzer continuous

beeping

Overload Remove some loads

APPENDIX B. SPECIFICATIONS

MODEL 500 650 800

Capacity 500VA 650VA 800VA

Bypass Capacity 300VA 300VA 300VA

No. of sockets Two UPS Sockets and One Bypass

Socket

Voltage (on battery) Simulated sine wave at

100V/110V/115V/220V/240V +/-5%

Frequency(on battery) 50 or 60Hz +/-0.3Hz

OUTPUT

Transfer Time 2/4 milliseconds, including detection

time

Voltage(single phase) 110V+20%/-15% at line input,

110V/115V/+/-20% at line input

220V+/-25% at line input,

240V+15%/-20% at line input

INPUT

Frequency 50 or 60Hz+/-10% ( auto sensing)

Unit Input Fuse for overload & short circuit

protection

Overload Protection

UPS automatic shutdown if overload

exceeds 105% of nominal at 20

seconds, 120% at 10 seconds,

130% at 3 seconds

PROTECTION

Short Circuit UPS output cut off immediately

Type Sealed, maintenance-free lead acid

batteries, with3-6 years typical lifetime

LED Indicators Battery Check

Typical Recharge Time

(to 90% of full capacity)

4 hours

Back up Time (minutes)

(PC with 15” monitor)

10-25

minutes

15-30

minutes

18-33

minutes

BATTERY

Protection Automatic self-test, Over discharge

protection, short circuit protection by

fuse

Net weight Kg(lbs) 3.6(7.9) 3.7(8.1) 3.8(8.3)PHYSICAL

Dimension(mm)WxDxH 70*297*195

(2.8*11.7*7.7)

Dry contact Sends battery low & power failure

signals , and receives shutdown signal

from computer

INTERFACE

RS232 Detect battery low, Schedule UPS

on/off, AS input/output power status

display

Battery Back-Up Slow beeping sound every 4

seconds(buzzer can be turn off by

pressing “buzzer stop” button)

Battery Low Rapid beeping sound every second

105% load Continue beeping sound every 4

seconds

ALARM

Overload Continue beeping sound, Overload

LED Always On

Ambient operation 3,500 meters max. elevation, 0-95%

humidity ( non-condensing water),

0-40℃

ENVIRONMENT

Audible Noise <40dBA(1 meter from surface)

All trademarks are property of their respective owners. Specifications subject to

change without notice.

661-EK50-000

Andere Handbücher für 800VA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Powercom UPS Handbücher

Powercom

Powercom 325A Bedienungsanleitung

Powercom

Powercom 600A Bedienungsanleitung

Powercom

Powercom 1000 Bedienungsanleitung

Powercom

Powercom 1000AP Bedienungsanleitung

Powercom

Powercom 1000VA Bedienungsanleitung

Powercom

Powercom 1000A Bedienungsanleitung

Powercom

Powercom 1000 Bedienungsanleitung

Powercom

Powercom 1025VA Bedienungsanleitung

Powercom

Powercom 425A/AP Bedienungsanleitung

Powercom

Powercom IMD-1025A Bedienungsanleitung

Powercom

Powercom 5K VA Betriebsanleitung

Powercom

Powercom 800VA Bedienungsanleitung

Powercom

Powercom 250 Bedienungsanleitung

Powercom

Powercom SKP-500A Bedienungsanleitung

Powercom

Powercom AP-1026 Bedienungsanleitung

Powercom

Powercom 425A Bedienungsanleitung

Powercom

Powercom Line-Interactive 1025AP Bedienungsanleitung

Powercom

Powercom WOW-300 Bedienungsanleitung

Powercom

Powercom Line-Interactive 1025AP Bedienungsanleitung

Powercom

Powercom 500S Bedienungsanleitung

Powercom

Powercom 600A Bedienungsanleitung

Powercom

Powercom 325A Bedienungsanleitung

Powercom

Powercom 800VA Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung