Powerlink PL-3000 SERIES Konfigurationshandbuch
1
FEATURES AND OPERATIONS
TWO WAY COMMUNICATION
REMOTE STARTER & SECURITY SYSTEM
OWNER'S MANUEL
2
TRANSMITTER OPERATIONS
ONE WAY TRANSMITTERS FOR
PL-3000 & PL-7000 SERIES TWO WAY TRANSMITTER FOR
PL-3000 SERIES TWO WAY LCD TRANSMITTER FOR
PL-7000 SERIES
COMMON BUTTON USED BY 3 TYPES OF TRANSMITTERS
:ARM & LOCK THE DOORS
:DISARM & UNLOCK THE DOORS
:ENGINE START
2 sec: TRUNK OPENER
2 sec: COLD START EVERY 3 HOURS
, :TEMPORARY VALET MODE
2 sec: PANIC MODE
3
TRANSMITTER OPERATIONS
TRANSMITTER FOR PL-3000 SERIES
AUX:TRUNK OPENER
AUX 2 sec: SLIDE DOOR OPEN
, (AT THE SAME TIME): SELECT 1ST OR 2ND VEHICLE
, AUX (AT THE SAME TIME): BATTERY SAVER: SELECT PAGING ON/OFF
LCD TRANSMITTER FOR PL-7000 SERIES
F THEN :STATUS REPORT S THEN :STATUS REPORT
F THEN :TEMPERATURE CHECK (optional) S THEN :SLIDE DOOR OPEN
F THEN :ENGINE START TIMER S THEN :STATUS REPORT
•Every time you press a button, transmitter emits 1 short beep. If you keep pressing the same button you will hear a
second beep. Depending on the number of beeps (1 short or 2 short beeps) you will have access to the different
functions of the system.
•When alarm is triggered the system will page the transmitter. To stop the alarm it requires pressing any button on the
remote.
4
TWO WAY LCD TRANSMITTER OPERATIONS
(Option)
Adjust real time clock
Keep pressing "F" button until appear then release. The display will show the hour numbers flashing. Use " "
button to select the hour, minutes or Am/Pm. Then use the "" button to increase or the "" button to decrease
time. When it is done, press "F" button to exit.
5
TWO WAY LCD TRANSMITTER OPERATIONS
Adjust start timer
Keep pressing "F" button until appear then release. The display will show the hour numbers flashing. Use ""
button to select the hour, minutes or Am/Pm. Then use the "" button to increase or the "" button to decrease
time. When the start timer is set, you can enable or disable it by pressing the "F," button. The "Start timer" icon will
turn ON and the engine of your vehicle will start at preset time. When it is done, press "F" button to exit.
NOTE: You can exit a mode anytime by pressing the "F" button.
Adjust wake-up timer
Keep pressing "F" button until appear then release. The display will show the hour numbers flashing. Use " "
button to select the hour, minutes or Am/Pm. Then use the "" button to increase or the "" button to decrease
time. When the wake-up timer is set, you can enable or disable wake-up by accessing the "S" functions. When it is done,
press "F" button to exit.
Enable wake-up timer
Keep pressing "S" button until appear then release. Then use the "" button or the "" button to
enable/disable this option. The "wake-up timer" icon will turn ON if it is enable.
6
TWO WAY LCD TRANSMITTER OPERATIONS
Change SOUND / VIBRATION mode
Keep pressing "S" button until appear then release. Then use the "" button or the "" button to toggle
between SOUND or VIBRATION option. The corresponding "Audible" or "Vibration" icon will be display.
Replace the battery
If you want to replace the battery without readjust the time and all your settings, use the following instructions. Keep
pressing "S" button until appear then release. Then press the "" button or the "" button, you will see
displayed. Now, you can replace the battery. Otherwise, press "S" button to exit this mode.
Enable/Disable paging
If you do not want the transmitter paging, you can disable the paging option. Keep pressing "S" button until
appear then release. Then press the "" button or the "" button to enable/disable this option. When this option is
disable, the battery will last more long time however, you will lose the paging feature. When it is done, press "S" button to
exit this mode.
7
TRANSMITTER OPERATIONS
FUNCTION BUTTON PRESSING REMOTE AUDIBLE
FEEDBACK ACTIVATION
BUTTON ARM:
ARMING NO CHIRP Press once 1 Hi/Lo beep
¦ Arm & lock ON System armed and doors
locked without chirp
ARMING WITH CHIRP Press twice 1 Hi/Lo beep
¦ Arm & lock ON System armed and doors
locked with 1 chirp
PANIC MODE Press 2 seconds while ignition
OFF 15 seconds alarm beep
¦ Paging ON Panic mode activation
BUTTON DISARM:
DISARMING NO CHIRP Press once 1 Hi/Lo beep
¦ Arm: OFF & unlock: ON System disarmed and doors
unlocked without chirp
DISARMING WITH CHIRPS Press twice 2 Hi/Lo beeps
¦ Arm: OFF & unlock: ON System disarmed and doors
unlocked with 2 chirps
TRUNK OPEN Press 2 seconds 3 Hi/Lo beeps Trunk opened
¦PL-7000 series LCD transmitter icons display only.
8
TRANSMITTER OPERATIONS
BUTTON START:
START ENGINE Press once 1 Cricket sound beep Send signal to start engine
STOP ENGINE Press once 1 Cricket sound beep followed
by 3 long beeps after a 4
seconds delay
Send signal to stop engine
Press once 3 long beeps System cannot start the
engine
KEYLESS RUNNING MODE
(when engine is running) Press once 1 Cricket sound beep Activation of keyless running
mode
NIGHT TIMER MODE Press 2 seconds 4 Cricket sound beeps Night timer mode activated
TEMPORARY VALET MODE Press twice while system
disarm 4 Hi/Lo beeps System keep disarm until
pressing
BUTTON " AUX "AUXILIARY (for PL-3000 series transmitter):
TRUNK OPEN Press once 3 Hi/Lo beeps Trunk opened
SLIDE DOOR OPENED Press twice 3 Hi/Lo beeps Slide door opened
SLIDE DOOR OPENED Press 2 seconds 3 Hi/Lo beeps Slide door opened
9
TRANSMITTER OPERATIONS
PAGING SIGNALS TO TRANSMITTER:
1 Hi/Lo beep Automatic arming or security rearm engaged
3 Long beeps Engine stops running via remote or engine running time has expired
5 Hi/Lo beeps Alarm has been triggered while you were away
15 Long beeps Alarm in progress
1 Cricket sound Engine running via remote and doors locked
2 Cricket sound Engine running via remote and doors unlocked
3 Cricket sound Engine running via remote and trunk opened
SIGNALS EMITTED BY TRANSMITTER:
3 Double beeps Error signal or out of range
Intermittent beeping Low battery indicator
IMPORTANT NOTE: If you have intermittent beeping on your transmitter, you have to reset transmitter by
removing battery and putting it back so that you can disarm your vehicle. Replace battery as soon as possible.
10
FEATURES AND OPERATIONS
ARMING:
Arming the system will also enable the starter kill and lock the doors, if installed. You can select silent or audible arming by
programming option #3. If you try to arm the system and you hear 3, 4 or 5 beeps, one of the protected zones is opened.
The system will ignore the defective zone and force the system to arm. Consult your installer to check your system.
PASSIVE ARMING:
If selected, the system will automatically arm itself 30 seconds after the ignition has been turned OFF and the last door
closed.
DISARMING:
Disarming the system will also disable the starter kill and unlock the doors, if installed. If you hear 5 beeps when you
disarm the system, it is means the alarm has been triggered while you were away.
SAFETY REARMING:
If you disarm the system by accident and you do not open any access, it will rearm automatically after 30 seconds, unless
the engine is running.
STARTER KILL OPERATION:
When the system is armed manually or via passive arming the starter kill will arm at the same time.
TURBO MODE:
When the engine is running with ignition key and the turbo mode is enable, press button to activate keyless running
mode. The engine is keep running 4 or 6 minutes (ask your dealer for this feature).
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
