Powermat PM-500-SSTT Bedienungsanleitung

ORIGINAL INSTRUCTIONS

USER MANUAL

BELT SANDER, tray

PM-500-SSTT

Table of Contents

SYMBOLS WARNING / INFORMATION .............................................. ........................................... 3

DESCRIPTION OF THE DEVICE ................................................ .................................................. ................................. 3

TECHNICAL DATA ................................................ .................................................. ................................ 4

PURPOSE OF THE DEVICE ................................................ .................................................. ............... 4

SAFETY RULES ................................................ .................................................. .................... 5

Workplace ................................................ .................................................. .................................................. .. 5

Safety in use ................................................ .................................................. ........................... 5

Safety related to the use and maintenance ............................................ ............................................... 5

General thoughts ................................................ .................................................. .................................................. 6 ..

Basic steps before you begin working ............................................. ............................................... 6

Actions during and after its completion ........................................... .................................................. ....... 6

It is forbidden to: ............................................... .................................................. .................................................. ..... 7

ASSEMBLY ................................................. .................................................. ............................................... 7

The installation disk grinding ............................................... .................................................. .............................. 7

Installing the top disk grinding .............................................. .................................................. ...................... 9

Installation stopper arm sanding ............................................. .................................................. ........... 9

OPERATION AND ADJUSTMENT DEVICE .............................................. .................................................. .... 10

Terms of use ................................................ .................................................. ..................................... 10

Adjusting the sanding belt centering .............................................. .................................................. .......... 10

Changing the position of the arm grinding .............................................. .................................................. ............... 11

Setting the angle stopper .............................................. .................................................. .................... 11

Tilting top grinding wheel .............................................. .................................................. .................... 11

The setting angle tabletop grinding wheel ............................................ ................................................. 12

Sanding belt replacement ............................................... .................................................. ............................. 12

Replacing the grinding wheel ............................................... .................................................. ............................. 12

MAINTENANCE ................................................. .................................................. ................................... 12

TROUBLESHOOTING ................................................ .................................................. ......... 13

REMOVAL OF USED ............................................... .................................................. ....... 14

COMPANY INFORMATION ................................................ .................................................. ............................ 14

DECLARATION OF CONFORMITY ................................................ .................................................. .................... 14

CONSTRUCTION SCHEME ................................................ .................................................. ............................. 15

SYMBOLS WARNING / INFORMATION SYMBOLS WARNING / INFORMATION

You should wear hearing protection.

Be used respiratory protection.

You should use eye protection.

DESCRIPTION OF THE DEVICE

1. Device

2. Working table.

3. Blade guard.

4. Stopwatch.

5. Lower blade guard ejection of waste.

6. Rubber feet.

7. Angle.

8. Shield.

9. 4mm hex wrench.

TECHNICAL DATA

motor power supply ~ 230V / 50Hz

Engine output no-load S 2 - 30 minutes Engine output no-load S 2 - 30 minutes Engine output no-load S 2 - 30 minutes 500W

belt speed 1450 rpm

size tape 100mm x 914mm

size shield 150mm

Working table 190mm x 125mm

Worktop shield 178mm x 126mm

tilt top 0 ° - 45 °

Gross weight 12g

Net weight 11kg

Sound power level L WASound power level L WA 92dB (A)

PURPOSE OF THE DEVICE

The device is intended for grinding at an angle of the materials for home use. Any other use, which clearly does not

allow this user manual, can lead to equipment damage and pose a serious threat to the user.

It is forbidden to use the machine in the rain or in a humid environment. The manufacturer is not liable for damages

that have arisen as a result of misuse or improper handling.

Because of safety reasons the device can not be used by children and young people under the age of 18

and by persons under the influence of alcohol, drugs or other intoxicants.

Persons who are not familiar with this manual, please read carefully before its first use.

SAFETY RULES

Workplace

• KEEP WORK AREA CLEAN. Mess in the workplace increases the likelihood of accidents.

• Pay attention to workplace conditions. Do not use tools in damp, wet. Do not expose to rain. Never use

electrical tools near flammable gases and liquids.

• KEEP CHILDREN AWAY FROM UNIT. Children should not be in the workplace. Each dispersal may cause

an accident. Do not allow children to carry the device or any accessories related to it.

Safety in use

• When working with tool use caution and common sense. Do not operate tool while under the influence of

alcohol, drugs and prescription drugs. Read leaflet drugs that you are taking, to see if they affect your

judgment and reflexes. If you have any doubt, do not operate the tool.

• Use appropriate protective accessories. When working with the tool, wear safety goggles, dust mask,

non-slip boots, helmet and ear protection whenever the situation demands. This will reduce the risk of

accidents.

• Avoid accidental start up the tool. Before plugging in, make sure the switch is in the OFF position. When

carrying the tools do not hold it by the switch, since this increases the risk of accidents.

• Remove any adjusting keys before running the tool. A key attached to the rotatable part of the tool can

cause injuries.

• Do not reach over the device. During operation, maintain a stable position and balance. This allows for

better control of the device in the event of unforeseen circumstances.

• Dressing up PROPERLY. Do not wear loose clothing or jewelry as they can be screwed into the moving

parts. It is recommended to work with the tool wear shoes with non-slip soles. Long hair should be

protected. Always wear suitable protective clothing.

• Use mounting workpiece. It is safer than using a hand support, as it allows you to use both hands to operate

the device.

Safety related to the use and maintenance

• Do not overload the tool. The device will work better and safer at loads for which it was designed. Do not try

to use incompatible accessories to increase productivity tools.

• Do not use a tool that has a damaged switch. A tool that can not be controlled with the switch creates a

danger and should be repaired.

• Before adjusting, repairing, changing accessories or storage, disconnect from the power tool. Such

precautions will reduce the risk of accidental starting.

• Keep the tool unplugged and out of reach of children and people

unauthorized.

• You should regularly carry out maintenance tool. Be sure to check that there is no backlash and faults

moving parts, they are not damaged parts or tools if there were no other defects that could disrupt the

proper operation of the device. In the event of irregularities should immediately repair the tool. Multiple

vulnerabilities has its source in improper maintenance.

•Use tools and accessories related to it in accordance with these instructions and in the correct manner. It should

take into account the conditions and the type of work performed.

• Using a tool misused can cause serious accidents.

• Faulty switch should be replaced by an authorized service. Do not use tools with defective On / Off switch.

• Do not leave tools unattended when it is turned on. Before leaving the workplace, always switch off and wait

for it to completely stop.

•If the main cable is damaged it must be replaced with the appropriate cable adapter.

• The cable can be obtained from the distributor device. The cable can be replaced by a service agent or a

qualified electrician.

General thoughts

• Electrical equipment should meet the requirements of health and safety of Polish Standards and the relevant

provisions for the lifetime.

• People employed in electrical devices should be equipped with suitable work clothing and personal

protective equipment.

• People employed in electrical equipment should comply with all health and safety regulations governing the

electrical equipment.

Basic steps before you begin working

• Before starting work, read the documentation of electrical equipment and to prepare the necessary tools,

equipment, warning signs and necessary equipment insulation.

• Check the condition of facilities and electrical installations (the insulation of wires, cables, plugs, switches,

sockets), zero, earth, fire and security status przeciwporażeniowych.

• Check the condition of the current security.

• Check the condition of fire marking equipment and electrical installations.

Actions during and after its completion

•Electric tools must be operated only in accordance with its intended purpose.

• If you need to leave the workplace should be supported to stop the machine and all other equipment that

may cause a hazard and disconnect the power.

• If necessary, work under pressure, use tools and equipment insulation and dielectric gloves and shoes.

• If the automatic switch-off or burn fuses, switch it on again when the cause of the short circuit and setting up

a new fuse.

• For connecting machines and equipment to be used grounded outlet, if required by the electrical installation.

• After the work, protect electrical equipment, organize the workplace, tools and equipment.

It is forbidden to:

• Acceptance of electrical equipment without confirmation of the effectiveness of protection against the

possibility of electric shock.

• Making changes to the supported device.

• Removal of protection, security, closing relays, blocking switches, fuses the use of temporary repairs, use

the wrong fuse.

• Fuse setting the machine turned on.

• Pull the cord when removing the electric plug from the socket.

• Maintenance of plug-in sockets, and plug-ins or the casing is damaged insulation insert.

•Overloading of electrical equipment above the permissible value.

• Touching live parts, terminal capacitors (even when they are disconnected).

•Leaving unattended electrical equipment connected to the network. All electrical equipment must be

disconnected from the mains before leaving the workplace.

• Access to devices or electrical unauthorized, minors, including children, sick people, under the influence of

alcohol or other drugs.

ASSEMBLY

Installing the grinding disc

1. Using a screwdriver, unscrew the 3 screws at the top of roll. 1. Using a screwdriver, unscrew the 3 screws at the top of roll.

2. Tighten cover drive to the device. 2. Tighten cover drive to the device.

3. Install the cover disc ejection by 4mm Allen key. 3. Install the cover disc ejection by 4mm Allen key.

4. Unscrew the four screws from the bottom cover. 4. Unscrew the four screws from the bottom cover.

5. Position the holes in the shells and tighten the four screws. 5. Position the holes in the shells and tighten the four screws.

Installing countertop grinding disk

1. Position the support table with a hole in the device and then place the support in 1. Position the support table with a hole in the device and then place the support in

hole.

2. To avoid injury to fingers countertop should be a few millimeters from the blade. tighten2. To avoid injury to fingers countertop should be a few millimeters from the blade. tighten

counter.

Installation stopwatch sanding arm

1. Unscrew a screw. 1. Unscrew a screw.