Powersoft DigiMod 1000 NPS Sicherheitsleitfaden

powersoft_connecting_dm1000nps_to_500_1000_1000IS_en_v1.0

Powersoft S.r.l. • Via Enrico Conti, 5 • 50018 Scandicci (FI) • Italy

+39 055 735 0230 • sales@powersoft.it • www.powersoft-audio.com

How To Connect a DigiMod

1000NPS to a DigiMod

500/1000/1000 IS

1 Introduction

1.1 Preliminary considerations

The DigiMod 1000NPS is an exact replica of the DigiMod 1000 output stage (2-channel bridgeable, 2x500W on 4Ω, 1x1000W on 8Ω),

which can be used in combination with DigiMod 500/1000/1000 IS to extend the range of possible multi-channel congurations and power

3-way active loudspeakers. In order to make this connection possible, the DigiMod 1000NPS must be equipped with an optional DSP-C

board.

Related Products:

▶DigiMod 1000NPS*

▶DigiMod 500

▶DigiMod 1000

▶DigiMod 1000 IS

* with DSP

1.2 Tools Needed:

▶1 male MOLEX 3-pin connector

▶1 female MOLEX 3-pin connector

▶1 male PHOENIX 5-pin connector (MSTB, 2.5/5-ST-5.08)

▶Balanced cable (low impedance)

▶Soldering iron and solder

▶Powersoft CB000098 cable or equivalent (10 pole 8/10 mm cable, with 2 MOLEX Micro-Fit 3.0 connectors)

▶pliers for electronic use

2 Procedure

2.1 Connect the Power supply

FIGURE 1: DigiMod 500 power supply connector position

▶2

How To Connect a DigiMod 1000NPS to a DigiMod 500

FIGURE 2: DigiMod 1000 power supply connector position

FIGURE 3: DigiMod 1000 IS power supply connector position

Use the CB000098 Powersoft cable to connect the DigiMod 500/1000/1000 IS power supply to the DigiMod1000NPS.

FIGURE 4: The DigiMod 1000NPS power supply connector

2.2 Master or Slave

Powersoft recommends using the module with a DSP on board as master module, while the module without a DSP should be used as a

slave1. In this particular case, the DigiMod 1000NPS will act as master module with its on board DSP, while the DigiMod 500/1000 will be

the slave module. DigiMod 1000 IS modules come equipped with a DSP board that must be removed in order to congure the module as

a slave module.

The onboard DSP has 4 outputs:

Channels 1 and 2 output directly from the DSP board. These two channels could be used, for example, to drive the rst two ways of a three

way system.

Channels 3 and 4 are used to carry the input signal over to the DigiMod 500/1000/1000 IS slave module through a MOLEX connector on

the DSP board itself. The DigiMod 500/1000/1000 IS will therefore receive channels 3 and 4 as input. In this conguration, the slave module’s

1Please note that this conguration is compatible with all presets Powersoft makes available to the public. Any other conguration is not guaranteed as compatible with Powersoft presets.

▶3

How To Connect a DigiMod 1000NPS to a DigiMod 500

output can be used, for example, in a bridged conguration to drive a subwoofer requiring more power.

2.3 How To Set Master And Slave Modules

Locate the jumpers on the modules

To set the module with DSP as MASTER: remove the jumpers in the pins BY22-BY33 in CN18 and BY31-BY21 in CN17 (the innermost

jumpers). Use pliers to aid in the removal (see Section FIGURE 5)

To set the other module (the one without DSP) as SLAVE: leave the jumper conguration as factory set.

FIGURE 5: Jumpers for setting a module as master or slave

3.3 Connecting the DigiMod 1000NPS To The DigiMod 500/1000/1000 IS

In order to connect the master module’s output channels (DigiMod 1000NPS) 3 and 4 from the DSP so they become inputs for the DigiMod

500/1000/1000 IS:

1. Remove the DSP from the DigiMod 1000NPS module

2. Take the male MOLEX 3-pin connector and solder this connector in the DSP board as seen in the picture below2

2Some DSP modules are equipped with a MOLEX connector at production time

▶4

How To Connect a DigiMod 1000NPS to a DigiMod 500

FIGURE 6: DSP with soldered MOLEX connector and three pin male MOLEX connector

3. Make the following cable so it connects DSP output channels 3 and 4 from the MOLEX connector to the DigiMod 1000NPS Phoenix

inputs. The cable will be balanced, low impedance and will have the following connectors:

▶1 3-pin female MOLEX

▶2 5-pin male Phoenix

4. Use the gure below as a connector pin soldering diagram.

FIGURE 7: Connector pin diagram

5-pin male Phoenix

Pin 1: GND

PIn 2: Hot Pole

Pin 3: Cold Pole

Pins 4 & 5: unused

3-pin female MOLEX connector:

Pin 1: Cold pole

Pin 2: GND

Pin 3: Hot pole

▶5

How To Connect a DigiMod 1000NPS to a DigiMod 500

In case of ground loop problems, remove the GND wire connection in the cable.

In order to connect the master module outputs to the slave module inputs:

1. Connect the cable that you’ve just made to the DSP in the DigiMod 1000NPS master module (with the MOLEX 3-pin connector).

2. Connect the other end of the cable with its two Phoenix 5-pin connectors to the slave module’s input connectors as seen in the gure

below:

FIGURE 8: DigiMod 500 Phoenix input connector

FIGURE 9: DigiMod 1000 Phoenix input connector (DigiMod 1000 IS is identical)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere powersoft Steuereinheit Handbücher

powersoft

powersoft LiteMod Bedienungsanleitung

powersoft

powersoft LiteMod Bedienungsanleitung

powersoft

powersoft IpalMod Bedienungsanleitung

powersoft

powersoft MiniMod 4 Bedienungsanleitung

powersoft

powersoft DSP LITE Bedienungsanleitung

powersoft

powersoft D-Cell504 IS Bedienungsanleitung

powersoft

powersoft DigiMod 3004PFC4 Bedienungsanleitung

powersoft

powersoft DigiMod 500 Bedienungsanleitung

powersoft

powersoft M-Drive Series Bedienungsanleitung

powersoft

powersoft DigiMod IS integration kit Bedienungsanleitung

powersoft

powersoft DigiMod 3004PFC2 Bedienungsanleitung

powersoft

powersoft LiteMod 4HC Bedienungsanleitung

powersoft

powersoft DigiMod IS Series Technisches Datenblatt

powersoft

powersoft IpalMod Bedienungsanleitung

powersoft

powersoft LiteMod 4HC Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

powersoft DigiMod 1000 NPS Sicherheitsleitfaden

Beliebte Steuereinheit Handbücher anderer Marken