Powerware 300 VA Bedienungsanleitung
POWERWARE®3110
300–700 VA
User’s Guide
www.powerware.com
Class B EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
SReorient or relocate the receiving antenna.
SIncrease the separation between the equipment and the receiver.
SConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
SConsult the dealer or an experienced radio/TV technician for help.
ICES-003
This Class B Interference Causing Equipment meets all requirements of the Canadian Interference Causing Equipment
Regulations ICES-003.
Cet appareil numérique de la classe B respecte toutes les exigences du Reglement sur le matériel brouilleur du Canada.
Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
SHarmonized Standards: EN 50091-1-1 and EN 50091-2
SEU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage limits
93/68/EEC, Amending Directive 73/23/EEC
89/336/EEC, Council Directive relating to electromagnetic compatibility
92/31/EEC, Amending Directive 89/336/EEC relating to EMC
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC
Declaration of Conformity, contact:
Powerware Corporation
Koskelontie 13
FIN-02920 Espoo
Finland
Phone: +358-9-452 661
Fax: +358-9-452 665 68
Powerware is a registered trademark of Powerware Corporation.
ECopyright 2001-2003 Powerware Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Powerware Corporation.
i
Powerware®3110 User’s Guide SRev B www.powerware.com
TABLE OF CONTENTS
1 Installation 1..................................................
Inspecting the Equipment 1.....................................................
Safety Precautions 1..........................................................
Quick Startup 2.............................................................
UPS Top and Side Panels 3.....................................................
2 Features 5.....................................................
Communication Options 5......................................................
USB Port 5..............................................................
DB-9 Communication Port 6..................................................
Battery Start Feature 7........................................................
RJ-11 or RJ-45 Surge Protectors 7................................................
3 UPS Maintenance 9.............................................
UPS and Battery Care 9........................................................
Storing the UPS 9.........................................................
Replacing Batteries 9.........................................................
Recycling the Used Battery 11....................................................
4 Specifications 13................................................
5 Troubleshooting 15..............................................
Service and Support 16.........................................................
Table of Contents
ii Powerware®3110 User’s Guide SRev B www.powerware.com
1
Powerware®3110 User’s Guide SRev B www.powerware.com
CHAPTER 1
INSTALLATION
This section explains:
SEquipment inspection
SSafety precautions
SUPS installation
SUPS top and side panels
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and
file a claim for shipping damage. If you discover damage after
acceptance, file a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with
the carrier within 15 days of receipt of the equipment; 2) Send a copy of
the damage claim within 15 days to your service representative.
Safety Precautions
Read the following precautions before you install the UPS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS. This manual contains important instructions that you
should follow during installation and maintenance of the UPS and batteries. Please
read all instructions before operating the equipment and save this manual for future
reference.
WARNING
SThis UPS contains its own energy source (batteries). The output receptacles may
carry live voltage even when the UPS is not connected to an AC supply.
SDo not remove or unplug the input cord when the UPS is turned on. This removes
the safety ground from the UPS and the equipment connected to the UPS.
Installation
2Powerware®3110 User’s Guide SRev B www.powerware.com
STo reduce the risk of fire or electric shock, install this UPS in a temperature and
humidity controlled, indoor environment, free of conductive contaminants. Ambient
temperature must not exceed 40°C (104°F). Do not operate near water or
excessive humidity (95% max).
SWith the exception of the user-replaceable battery, all servicing of this equipment
must be performed by qualified service personnel.
SBefore maintenance or repair, all connections must be removed. Before
maintenance, repair, or shipment, the unit must be completely switched off and
unplugged or disconnected.
CAUTION
SImportant Notice The UPS ground (earth) conductor carries leakage current from
the loads in addition to any leakage current generated by the UPS. This UPS
generates no more than 0.5 mA of current (120V model), or 1 mA of current (230V
model).
STo limit the total leakage current to 3.5 mA, the load leakage must be limited to
3 mA on the 120V model and 2.5 mA on the 230V model.
SIf you do not know the load leakage current, replace the UPS power cord (230V
model only) with a power cord that uses a locking plug with a minimum rating of
10A (such as IEC 309).
SIf you do not have a matching receptacle, consult an electrician to install the
proper receptacle.
SThe three-wire receptacle that you plug the UPS into must have a good
(low-impedance) ground (protective earth) connection to provide a safe path for
leakage current.
Quick Startup
The PowerwareR3110 provides protection against many power
problems, including power outages. It also provides spike suppression
and line noise filtering to protect your equipment.
1. On 230V models, plug the UPS power cord into the input
connector on the UPS side panel.
2. Plug the equipment to be protected into the UPS output
receptacles.
DO NOT protect laser printers with the UPS because of the
exceptionally high power requirements of the heating elements.
Installation
3
Powerware®3110 User’s Guide SRev B www.powerware.com
3. Start the UPS by pressing the switch as shown in Figure 2
or Figure 4 on page 4. The µindicator illuminates indicating
that power is available from the UPS output receptacles.
The unit beeps and the front panel LEDs illuminate several
times. The µindicator remains on, indicating normal
operation.
If the unit continues to beep, or if the µindicator is off even
though input power is available from the wall outlet, see
“Troubleshooting” on page 15.
NOTE Let the unit charge the battery for at least 3 hours. You may use the unit while
the battery charges, but the battery backup runtime will be reduced until the battery is
fully charged. This will take up to 8 hours after a full discharge while the UPS is fully
loaded.
UPS Top and Side Panels
Figure 1 and Figure 2 identify features of the 120V (USA) models, with
attached input line cord. Figure 3 and Figure 4 identify features of the
230V (European) models, which have a connector for the input line
cord as well as IEC output receptacles.
Fault Indicator
Output Receptacles
(Battery and Surge Protection) Output Receptacles
(Surge Protection Only)
Power Indicator
Figure 1. 120V Model Top Panel
Installation
4Powerware®3110 User’s Guide SRev B www.powerware.com
Circuit Breaker Power Cord On/Standby Switch
RJ-11 or RJ-45 Surge Protectors
Communication Port
USB Port
Figure 2. 120V Model Side Panel
5
Powerware®3110 User’s Guide SRev B www.powerware.com
CHAPTER 2
FEATURES
This section covers:
SUsing the USB or DB-9 communication port
SStarting the UPS on battery
Communication Options
The UPS is equipped with a USB and a DB-9 communication port. Either
the USB port or the DB-9 communication port may be used to monitor
the UPS; however, they cannot operate simultaneously.
USB Port
The UPS can communicate with a USB-compliant computer using
LanSafe Power Management Software (v4.15 or higher).
To establish communication between the UPS and a computer:
1. Connect the USB cable to the USB port on the UPS rear panel.
Connect the other end of the USB cable to the USB port on your
computer.
2. Install the LanSafe software and USB drivers according to the
instructions provided with the Powerware Software Suite CD.
Features
6Powerware®3110 User’s Guide SRev B www.powerware.com
DB-9 Communication Port
Powerware offers an accessory interface kit that allows you to connect
many types of computer systems to the UPS communication port. For
specific information on Powerware interface kits, call your service
representative.
Contacts consist of open collector circuits capable of switching up to
+30 Vdc, 6 mA resistive load.
Table 1. Communication Port Pin Assignment
Pin Signal Type Function
1RS-232 Level Shutdown +12 Vdc signal held for 5 seconds on this pin shuts the UPS down
120 seconds later. The UPS restarts after 15 seconds when utility
power returns.
2 Not Used Not Used
3Normally Open On-Battery Contact A normally open contact that closes 15 seconds (pulls to
Common) after the UPS switches to battery power.
4Common The signal ground for all signal pins.
5Normally Open Low-Battery-Alarm Contact A normally open contact that closes (pulls to Common) during a
Low Battery Alarm.
6Normally Closed Low-Battery-Alarm Contact A normally closed contact that opens (releases from Common)
during a Low Battery Alarm. This tells some shutdown software
when to start a computer shutdown.
7 Not Used Not Used
8Normally Closed On-Battery Contact A normally closed contact that opens 15 seconds (releases from
Common) after the UPS switches to battery power.
9 Not Used Not Used
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Powerware UPS Handbücher
Powerware
Powerware BPIV 30 kVA Bedienungsanleitung
Powerware
Powerware 5110 Bedienungsanleitung
Powerware
Powerware 9315 Bedienungsanleitung
Powerware
Powerware Prestige series 9 Bedienungsanleitung
Powerware
Powerware BPIV Bedienungsanleitung
Powerware
Powerware 9125 Bedienungsanleitung
Powerware
Powerware Prestige series 9 Bedienungsanleitung
Powerware
Powerware Ferrups FE/QFE 500VA Bedienungsanleitung
Powerware
Powerware 9125 Bedienungsanleitung
Powerware
Powerware 5125 Bedienungsanleitung
Powerware
Powerware UPS 1000 - 2200 Bedienungsanleitung
Powerware
Powerware 3110 Bedienungsanleitung
Powerware
Powerware 9395 Bedienungsanleitung
Powerware
Powerware 9390 Bedienungsanleitung
Powerware
Powerware 9305 HS Series Betriebsanleitung
Powerware
Powerware 9320 Bedienungsanleitung
Powerware
Powerware 5125 Bedienungsanleitung
Powerware
Powerware 8 - 15 kVA Bedienungsanleitung
Powerware
Powerware 9125 PowerPass Bedienungsanleitung
Powerware
Powerware 9315 Bedienungsanleitung
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
