PR Lighting PR-3400D Bedienungsanleitung

LED Studio (15W X 12)

3400D

3400T

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

2/14

INDEX

S FE US GE OF THE PROJECTOR………………………………………………………………………………

INST LLING THE PROJECTOR…………………………………………………………………………………..

CONTROL CONNECTION…………………………………………………………………………………………

DMX TERMIN TOR………………………………………………………………………………………………..

SETUP OPTIONS-PROJECTOR CONFIGUR TION………………………………………………………………

TO SET THE DMX ST RT DDRESS……………………………………………………………………………..

OPER TION MENU………………………………………………………………………………………………..

DMX PROTOCOL………………………………………………………………………………………………….

INDIC TION OF LED DIGIT L TUBE…………………………………………………………………………….

M INTEN NCE……………………………………………………………………………………………………

TROUBLESHOOTING………………………………………………………………………………………………

TECHNIC L D T …………………………………………………………………………………………………

ELECTRIC L DI GR M…………………………………………………………………………………………..

COMPONENT ORDER CODES……………………………………………………………………………………

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst

every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The

publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition

before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. ny damage caused

by improper use will not be assumed by the manufacturer and / or dealer.

CCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

Clamp 1 pcs

Safety cord 1 pcs

DMX cable 1 pcs With socket and plug

This manual 1 pcs

3/14

S FE US GE OF THE PROJECTOR

When unpacking and before disposing of the carton, check there is no transportation damage before using the projector. Should there

be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector can be used indoors and outdoors, IP20. Keep the projector clean; avoid its use in humid, hot and dusty places; keep

water and other liquids from touching the projector.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is 2m. 2m

void direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

When the projector is hanged to a high place, please use a safety cord provided to pass through the projector handles as a secondary

safety fixing for safety seasons. For details, refer to “INST LL THE PROJECTOR “section.

Exterior surface temperatures of the projector after 5 minutes’ operation is 45℃, when achieving steady state it is 55℃.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers

removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Always disconnect a projector from power, when the device is not in use or before cleaning or any

maintenance work !

4/14

INST LL THE PROJECTOR

Take 1 clamps and 1 safety cord out from the package and mount 1 clamp on the mounting handle of fixture with 1 retainer. Hang the

fixture on the structure and fasten the screws attached to the clamp. lways ensure that the projector is firmly anchored to

avoid vibration and slipping whilst functioning. lways ensure that the structure to which you are attaching the

projector is secure and strong enough to support the weight of the fixture. For safety the projector should have a

secondary fixing with a safety cord through the handle of the unit to ensure safe mounting.

Warning:

1. he projector MUS be lifted or carried by the HANDLES instead of clamps.

2. For safety the safety cord should afford 10 times of the unit’s weight.

5/14

CONTROL CONNECTION

Connection between the controller and a projector and between one projector and another must be made with a 2 core-screened cable,

with each core having at least a 0.5mm diameter. Please use the projector’s cannon 5- pin signal input and output cables as connection.

The 5-pin signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not

connected in any way. The projector accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input and connect

the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure below.

Each unit should be connected to power supply individually and the voltage and frequency of the power supply should match those

indicated on nameplate.

DMX TERMIN TOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an DMX connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (O M) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

6/14

SETUP OPTIONS-PROJECTOR CONFIGUR TION

Projector configuration and Start address can be set conveniently via push-button switch and LED display.

Launch the projector and press button FUNC for more than 3 seconds to unlock the panel, the LED will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPER TION MENU” section.

Press FUNC if you want to browse through the various Setup Options.

Press button UP or DOWN to enter sub-menus or change parameters(plus or minus).Press button FUNC to save your settings .

Press button FUNC, it will return to the main menu or browse through the main menu.

Without any operations after 3minutes, the LED display will be locked.

TO SET THE DMX ST RT DDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 1 DMX channel, so set the No. 1 projector’s address 001, No. 2 projector’s address 002, No. 3 projector’s

address 003, and so on.

Launch the projector. Press button FUNC for more than 3 seconds to unlock the panel.

Press button FUNC to find “ ddR” menu.

press UP or DOWN to set DMX address.

t this time, DMX address indication will flash continuously. Press button FUNC to confirm, then setup has been saved. When the

projector powered next time, the latest saved settings will automatically used.

Press button FUNC, it will return to the main menu or browse main Menu.

Operations Menu

7/14

level menu 2

level menu

DMX ddress

XXX

（001~512）

TEST

Test Mode 000-255

_ON

LKP saved after LED display locked

LKP

Information OFF

LKP OFF after LED display locked

_ON

ddress displayed after LED display locked

DSP

Display

OFF

Black LED display after it locked

DMX PROTOCOL

CHANNEL FUNC ION DMX DESCRIP ION

1 Dimmer 000-255 Dimming from dark to light

8/14

INDIC TION OF LED DIGIT L TUBE

ON DMX ddress

ddress Indication Flash DMX ddress changed

ON Brightness Value

TEST Indication Flash Brightness changed

ON Setup status

DSP Indication Flash Setup changed

ON Setup status

LKP Indication Flash Setup changed

ON DMX Signal OK，Receiving function OK

DMX Indication OFF DMX Signal B D，Receiving function B D

Instructions for the function setup of PR-3400

First, DSP: Setup of LED display off 3 minutes after no buttons are pressed

There are “ on” and “ off” options in the sub-menu. If “on” selected and

FUNC pressed, LED display will be on all

the time. If “off” selected, LED display will be off 3 minutes after FUNC pressed. ( LED display will be on 3 seconds

after FUNC pressed.

Second. LKP: Setup of saving of last brightness value.

There are “on” and “off” in the sub-menu. If “on” selected and FUNC pressed, L-P function on. If “off” selected and

FUNC pressed , L-P function off.. ctual display is “L-P”.

hird, ADD: DMX address Setup. Press

UP or DOWN to set channel value, if the channel value set and

FUNC pressed,

current DMX channel value saved.

Fourth, ES : Setup of Manual Dimming

If this option selected, press

UP or DOWN to set the brightness value between 0 and 255.

ctual display is “LES”.

Fifth, LED display of five functions

1. DD: if DD selected and sub-menu “512” entered, DD indication on; while DMX channel is being

selected , DD indication flashes, which means channel selected has not been saved, fter

FUNC pressed , DD

indication off and Channel saved.

2. TEST: if TEST selected, first press either of UP and DOWN, “000” status has been entered and TEST indication on,

after which either of UP and DOWN is pressed, TEST indication flashes. If UP or DOWN pressed long, TEST

indication will change statuses from “flash” to “ON”, after the button released, TEST indication goes back to Flash

Status.

3. DSP: if DSP selected, enter into sub-menu of “on” or “off”, DSP indication on. While “on” or “ off” being selected,

DSP indication flashes, if

FUNC pressed long, DSP indication off which means LED Display settings have been saved.

4. LKP: If L-P selected, enter sub-menu “on” or “off”, LKP indication on. If “on” or “ off” is being selected, LKP

indication flashes, if

FUNC pressed long, LKP setup is saved.

5. fter DMX cable plugged, LDMX green indication is on ,which means DMX works normally.

9/14

M INTEN NCE

To prolong the life of the projector, it is very important to do the maintenance work. I

f the projector is idle for a long time,

damp,

smoke or particularly dirty surroundings can cause greater accumulation of dirt on its cover and housing.

So it should be cleaned to

maintain an optimum light output and at the same time to prevent it from being corrupted by acid gas.

Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning products should be

used for cleaning. It is recommended to clean projector at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

TROUBLESHOOTING

PROBLEM AC ION

The projector doesn’t switch on

 Power connection is not correct.

 Power supply is damaged or abnormal. Call a qualified personnel to fix

it.

 Connection of control board is not correct. Call a qualified personnel to

fix it.

The projector can be turned on, but LEDs do not

emit light and are out of control.

 Connection of LED board is not correct. Call a qualified personnel to fix

it.

The lamp comes on but the projector doesn’t

respond to the controller

 Make sure that the projector is correctly configurated.

 Replace or repair the DMX cable.

The beam appears dim  The projector is too hot. Take ventilation measures to make it cool.

10/14

TECHNIC L D T

VOL AGES:

90V-240V C, 50/60Hz

POWER CONSUMP ION:

PR-3400D 190W

PR-3400T 190W

LED:

Power consumption 15W （DC 12V）

Quantity

12pcs

Manufacturers Rated LED Life More than 50000 Hours

COLOUR EMPERA URE:

PR-3400D 5600K

PR-3400T 3200K

DIMMER:

0-100% linearly adjustable

BEAM ANGLE:

Field angle(one-tenth-peak) θ

113°

CON ROL:

DMX512, 5 pin interfaces

HOUSING:

High-intensity die-casting aluminum, IP20

WORK ENVIRONMEN EMPERA URE:

-20°C~40°C

WEIGH :

8.2 kg

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Projektor Handbücher

PR Lighting

PR Lighting XR380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XR 330 SPOT Bedienungsanleitung

PR Lighting

PR Lighting XPar 360-W Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Spot Bedienungsanleitung

PR Lighting

PR Lighting XRLED 700 Spot Bedienungsanleitung

PR Lighting

PR Lighting PR-2720 Bedienungsanleitung

PR Lighting

PR Lighting XRLED 500 SPOT Bedienungsanleitung

PR Lighting

PR Lighting PRO-PAR Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 Bedienungsanleitung

PR Lighting

PR Lighting AQUA MARINE 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting XRLED 1800-W Framing Bedienungsanleitung

PR Lighting

PR Lighting XR330 Framing Bedienungsanleitung

PR Lighting

PR Lighting PRO-PAR D Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Spot Bedienungsanleitung

PR Lighting

PR Lighting PRO STAGE PR-3051 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting XPar 360 PR-8955 Bedienungsanleitung

PR Lighting

PR Lighting XPar 336 Bedienungsanleitung

PR Lighting

PR Lighting LSBAR 336 Bedienungsanleitung

PR Lighting

PR Lighting Solo 1200 Leitfaden

PR Lighting

PR Lighting XLED 1037 PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting XS 1200 Beam Bedienungsanleitung

PR Lighting

PR Lighting XPar 1514 ZOOM Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung