PR Lighting XRLED 700 Spot Bedienungsanleitung

XRLED 700 Spot

PR-8163

This product manual contains important information about the safe installation and use of this projector.

Pleaseread andfollowthese instructions carefullyandkeepthis manualin asafeplace forfuturereference.

PR LIGHTING LTD.

http://www.pr-lighting.com.cn

Pure Reliability lighting

2/24

INDEX

1. SAFEUSAGEOFTHEPROJECTOR

2. INSTALLINGTHEPROJECTOR

3. POWERSUPPLY–MAINS

4. CONTROLCONNECTIONS

5. DMXTERMINATOR

6. SETUPOPTIONS-PROJECTORCONFIGURATION

7. TO SETTHE DMXSTARTADDRESS

8. STAND-ALONE MODE

9. MASTER/SLAVEMODE

10.TECHNICALDATA

11.OPERATIONMENU

12.REPLACING GOBOS

13.DMXPROTOCOL

14.INDICATIONOFLEDDIGITALTUBE

15.MAINTENANCE

16.LUBRICATION

17.KEEPINGTHEPROJECTORCLEAN

18.TROUBLESHOOTING

19.COMPONENTORDERCODES

20.ELECTRICALDIAGRAM

21. PCB CONNECTIONDIAGRAM 22

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst

every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The

publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition

before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused

by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

Theseitems arepackedtogether with theprojector:

Name

Quantity

Unit

Remark

Gclamps

Pcs

XLRcable

withplugand socket

Safetycord

Pcs

Thismanual

Power cord

Ω clamps

Pcs

Optional

XLRterminator

Optional

3/24

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there

beanydamagecausedbytransportation, consultyourdealeranddonot usetheapparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat,

humidityanddust.Do not allowcontact withwateroranyother liquids.

Ifthedevice hasbeenexposed to drastictemperaturefluctuation(e.g.after transportation), do notswitchitonimmediately.

Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the fixture at the transport

handles.

Theprojectorisonly intended forinstallation,operationand maintenancebyqualifiedpersonnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure that no

ventilationslotsareblocked.

Do notprojectthebeamontoinflammable surfaces,minimum distanceis1.3m. 1.3m

Avoiddirectexposureto the lightfrom thelamp.Thelightisharmful totheeye.

Do not attempt to dismantle and/or modify the projector in any way. The maximum ambient temperature 45°C must never be

exceeded.

Electricalconnection mustonlybecarriedoutbyqualified personnel.

Beforeinstallation,ensurethatthe voltageandfrequencyofpower supplymatch thepowerrequirementsoftheprojector.

Itisessentialthateachprojectoriscorrectlyearthed and thatelectricalinstallationconforms toallrelevant standards.

Do notconnectthisdeviceto anyothertypesofdimmerapparatus.

Make sure that the power-cord isnever crimped or damaged bysharp edges. Never let the power-cordcomeintocontactwithothercables.

Onlyhandlethe power-cordbytheplug.Neverpullouttheplugbytuggingthepower-cord.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as

shown in “installing the projector” section.

Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired, for

example bycracksordeep scratches.To applypower, firstcheckthat the head panand tiltlocksarereleased.

Exteriorsurfacetemperaturesoftheluminaireafter 5 minutesoperationis45℃,when steadystateisachieved50℃,

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers

removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

AlwaysdisconnectionfromPowerbeforeadevice’s installation ,cleaningandmaintenance !

4/24

INSTALLTHE PROJECTOR

Handle Safety cord Clamp

Operation menu

106

Warning

Please run the safety cord

through a safety cord hole

for safety.

Safety cord hold

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of

the base as shown above) To pass SAFETY CORD through 1 HOLE for safety! Always ensure that the projector is firmly

anchored to avoid vibration and slipping whilst functioning. Always ensure that the structurethat youaregoingto mount the projector

issecureandisstrongenoughtosupporta weightofeachprojector.

WARNING:

1.Adevice MUSTbeliftedorcarriedbyitsHANDLESinsteadofclamps.

2. For safety the safety cord should afford 10 times the unit’s weight.

5/24

POWER SUPPLY-MAINS

Connectthepowercord asfollows:

L(live) =brown

E(earth)=yellow/green

N(neutral)=blue

Ifyouinstallacordcaponthepowercabletoallowconnectiontopoweroutlets,installagrounding-type(earthed) plug, following

the plug manufacturer’s instructions.

Toapplypower,firstcheck thattheheadpanandtiltlocksare released.

Thecoresinthepowercablearecoloured accordingtothe followingtable.

Core(EU)

Core(US)

Connection

PlugTerminalMarking

Brown

Lightblue

Yellow/Green

Black

White

Green

Live

Neutral

Earth

Theearthhasto beconnected!

If youhave anydoubtsaboutproperinstallation,consultaqualifiedelectrician.

Use the plug provided to connect the mains power to the projector paying attentionto the voltage and frequency marked on the panel

oftheprojector. Itisrecommendedthateachprojectorbesuppliedseparatelyso thattheymaybeindividuallyswitchedonand off.

IMPORTANT

Itisessentialthateachprojectoriscorrectly earthedandtheelectricalinstallationconforms to allrelevantstandards.

Fixtures

must

installed

Qualified

electrician

accordance

with

all

national

and

local

electrical

and

construction

codes

and

regulation.

6/24

CONTROLCONNECTION

Connection between controller and projector and between one projector and another must be made with a 2 core-screened cable, with

each core having at least a 0.5mm diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector).The XLR'sare connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touchthe metallic bodyofthe plug or each other. The bodyof theplug is not

connected inanyway.Theprojectoracceptsdigitalcontrol signalsinprotocolDMX512(1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input and connect

the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure below.

XLR

terminator

Input Output Input Output Input Output

DMX512

DMX

controller

NO.1 NO.2 NO.n

DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electricalnoise fromdisturbingand corruptingtheDMXcontrol signals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

intothe output socket onthe lastprojector inthe chain.Theconnectionsare illustratedbelow.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

7/24

SETUPOPTIONS-PROJECTOR CONFIGURATION

Adeviceconfigurationcanbesetconvenientlyviapressbuttonswitchand LCDdisplay.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel, LCD display shows functional menus which have

their ownsub-menusfordesignatedfunctions,thebelowisthedetails

Pressbutton UP or DOWN ifyouwant tobrowse through thevariousSetupOptions.

Pressbutton ENTER to save your settings or enterthe next menu.

Pressbutton UP or DOWN to shift.

Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status

automatically.

TO SETTHE DMX STARTADDRESS

Eachprojector mustbegivenaDMX startaddress sothat the correctprojector responds to the correct control signals.ThisDMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The fixture have 3 DMX modes. There are standard mode, extended mode and short mode. For example standard mode

has 19 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 020, No. 3 projector’s address 039, No. 4

projector’s address 058, andsoon.

Launchtheprojector. Pressbutton ENTER more than5 secondsto unlockpanel.

Pressbutton FUNC todisplayDMXaddress;

Pressbutton UP and DOWN,youcanset theaddress;

Pressbutton ENTER to confirm,afterpowered nexttime,thelastsaved settingswillbeshowed.

Pressbutton FUNC,it willreturnto the upper menuonebyone.

STAND-ALONE MODE

Operate the projector without connecting a controller, enable the master mode in the operation panel, the projector

will run in Stand-Alone mode automatically.

DMX address can be set without limitations.

MASTER/SLAVE MODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. Select one

projector as the master with setting options at any mode of master’s modes enabled and make the other projectors as

the slaves with setting options slave mode enabled and their DMX start address “001”.

Using XLR-XLR cables, Connect the first fixture’s output to the second fixture’s input, and connect the second fixture’s output to the

third fixture’s input and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as

showninthe figurebelow.

Afterpowered,thegroupwillruninsynchronous Master/Slave Mode.

W-DMXDMX

PR-8163

XRLED 700 Spot

8/24

XLR

Terminator

Input Output Input Output Input Output

Master Slave Slave

TECHNICALDATA

1. VOLTAGES:

100V~240VAC，50/60Hz

2. LightSource:

Power:320W

Color:White

ColorTemperature：8000K±500K

3. POWERCONSUMPTION:

400W@220V

4. COLOURS:

1+6Colors(Orange,Magenta,DeepBlue,Red,Green,Yellow)

Withvariable speedbi-directionalrainboweffect

5. GOBOS:

1 Rotatinggobo wheel:7interchangeablegobos+ white,glassormetalgoboscanbe fixed

Indexable,bi-directionallyrotatableandWheelScrollingatvariablespeeds,shakableat variablespeeds

9/24

GoboDiameter:Φ27.8mm Gobo image diameter: Φ23mm Thickness:1.1mm, highfloatglassorbetter

1Fixedgobo wheel :7 interchangeable gobos+ white

Gobo diameter: Φ27.8mm Gobo image diameter: Φ23mm Thickness:0.4mm

6. PRISM

1x3 facet prism, bi-directionallyrotatable at variable speeds

7. Iris

Linearlyadjustedwith Macros

Electroniciris fordifferentsizebeam

8. FrostFilter

1pc IndependentFrostFilter

9. FOCUS:

linearlyfocusingcontrolledbyDMX

10. DIMMER:

0-100%linearlyadjustable

beehi

ve1

Beehive1

Pockets2

Curves3

Snows4

Swirls5

Dots 6

Plumblossom7

Dots 1

Squares2

Flames3

Flowers4

Scrappapper5

Crisscrossing6

Stars 7

10/24

11. Strobe:

Electronicstrobe,0.3~20 F.P.S

12. HEADMOVEMENT:

Pan0º~540º,Tilt0º~270ºwith auto positioncorrection

SwapandInvertfunctionsofPanandTilt

13. BEAMANGLE:

12°～36°linearadjustment

14. CONTROL:

DMX512,3pin,5pininterfaces

15channelsin short mode,19 channels in standard mode, and23channelsinextended mode.

Master/slavemode

Stand-alonemode(Presetsprocedure,User procedure)

Self-testmode andManualcontroltestmode

15. OTHERFUNCTIONS:

AdjustablePan&Tiltspeed

Fixtureusage timedisplay

Software versiondisplay

DMX512 wirelessavailable

OptionalDMX512wirelessremitter

16. HOUSING:

Compositeplastic,IP20

17. WEIGHT:

Net:24Kg

GrossWeight:29.5Kg,inCarton(1pc/ctn)) includingaccessoriessupplied,; 52KGinflight caseincludingaccessoriessupplied

18. SIZES:

Seeatbelow

410

422

542

377

445

338

650

Andere Handbücher für XRLED 700 Spot

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Projektor Handbücher

PR Lighting

PR Lighting XPar 360 PR-8955 Bedienungsanleitung

PR Lighting

PR Lighting XS 1200 Beam Bedienungsanleitung

PR Lighting

PR Lighting PR-2720 Bedienungsanleitung

PR Lighting

PR Lighting PRO-PAR Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 Bedienungsanleitung

PR Lighting

PR Lighting XLED 1037 PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting XR380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting LSBAR 336 Bedienungsanleitung

PR Lighting

PR Lighting XRLED 1800-W Framing Bedienungsanleitung

PR Lighting

PR Lighting PRO STAGE PR-3051 Bedienungsanleitung

PR Lighting

PR Lighting XR 330 SPOT Bedienungsanleitung

PR Lighting

PR Lighting XRLED 500 SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PRO-PAR D Bedienungsanleitung

PR Lighting

PR Lighting XPar 360-W Bedienungsanleitung

PR Lighting

PR Lighting Solo 1200 Leitfaden

PR Lighting

PR Lighting AQUA MARINE 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting XPar 1514 ZOOM Bedienungsanleitung

PR Lighting

PR Lighting PR-3400D Bedienungsanleitung

PR Lighting

PR Lighting XR330 Framing Bedienungsanleitung

PR Lighting

PR Lighting XPar 336 Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Spot Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Spot Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

Epson

Epson PowerLite 810p Bedienungsanleitung