Precision Drone Onset Bedienungsanleitung
User's Manual
Onset/Scout Model
2014
Table of Contents
(1) Warnings........................................................................................2
(2) What's in the case?.........................................................................4
(3) Detailed omponents......................................................................5
(4) Getting Everything harged.............................................................9
(5) GPS Recalibration..........................................................................10
(6) Pre-Flight......................................................................................11
(7) Flight............................................................................................12
(8) Post-Flight.....................................................................................14
(9) rop Health Imaging......................................................................14
(10) Rotation Diagrams.........................................................................15
1 2 Page 1
WARNINGS
Obey all federal, state, and local regulations
Do not fly in rain or other harsh conditions
Do not fly in wind more than 20mph
Do not fly faster than 10 m/s (22.5mph)
Operating in temperatures below 50° Fahrenheit (10° elsius) will result in
decreased flight times
Operating in temperatures below 32° Fahrenheit (0° elsius) and below the
mechanical and electrical components run the chance of seizing, resulting in
drone malfunction and ultimately property damage, injury, and/or death
Always use the provided battery chargers
The drone will land in place when it reaches 10.5v
Keep away from spinning motors at ALL TIMES.
Do not attempt to modify the drone
Do not attempt to repair the drone
NEVER allow minors to charge battery packs
NEVER drop power supply or batteries
NEVER attempt to charge damaged batteries
NEVER let batteries fully discharge unless you are disposing of them
NEVER attempt to charge a battery pack containing different types of batteries
NEVER charge a battery if the cable has been pinched or shorted
NEVER allow batteries to come into contact with moisture at any time
NEVER charge batteries in extremely hot or cold places or in direct sunlight
ALWAYS disconnect the battery after charging
ALWAYS end the charging process if the charger or battery becomes too hot
1 3 Page 2
*Failure to exercise caution while using this product and comply with the warnings above
could result in product malfunction, electrical issues, excessive heat, fire, and ultimately
injury, property damage, or death. Never allow use of this product by anyone without
providing them with these instructions. You must read, understand, and follow all instructions
and warnings for any product(s) to which this product is used in conjunction with or installed.
The operator is choosing to use this product and does so at his or her own risk. Save these
instructions with the product for use as a reference in the future
1 4 Page 3
What's in the case?
List of Case Components
1x Precision Drone Onset OR Scout
3x 4000mAh 3S LiPo Battery (Onset model) OR 4x 5000mAh 3S LiPo Battery (Scout model)
1x Live Feed Monitor (Scout model)
1x Live Feed Monitor harger (Scout model)
1x Precision Vision amera (RGB)
1x Precision Vision amera (IR) (If equipped)
1x amera harge able
1x DX8 ontroller
1x ontroller harger
1x ontroller Strap
1x Bind Plug
1x Battery harger
1x Balancing Board
1x Gator lips
1x harger Wall Plug
1x harger Battery Plug
1x 16GB SD card (pre-installed in camera)
OEM Manuals (Located under first layer of foam)
1 5 Page 4
Components
DX8 ontroller:
1 6 Page 5
Battery harger:
1 7 Page 6
Live Feed Monitor:
1 8 Page 7
Precision Vision amera:
1 9 Page 8
Gettin Everythin Char ed
DX8 Controller: Turn the controller off. Plug one end of the charging cable into the
charging port (see p. 5), and the other end into a power outlet. The controller
indicator LED will glow blue indicating it is charging.
Precision Vision Camera: Turn the camera off. Plug the mini USB cable into the USB
port on the camera (see p. 8), and the other end into a generic USB port on a laptop
or similar device connected to power.
Live Feed Monitor: The monitor can remain powered on while charging. Plug one
end of the charging cable into the bottom D IN port on the monitor (see p. 7), and
the other end into a power outlet. The charging indicator LED will glow red. It will turn
green when finished.
IMPORTANT:
DO NOT leave it in prolonged exposure to sunlight while charging!
Batteries: (see p. 6) Plug the battery charger into a power outlet using the power
cable. Attach the red and black leads to their respective positions on the charger.
Attach the balancing board to the balancing port on the charger. Now take the
red/black leads and connect it to the battery. onnect the white balancing cable to the
balancing board. Make sure everything is secure and snug. The charger should now be
switched to “ HARGE” mode (it is already on by default). Now hold down the enter
button for a few moments, then tap it again to confirm, it will now charge the battery.
The charger will beep and flash “FULL” when finished. Hit “STOP”.
IMPORTANT:
DO NOT disconnect the red/black terminals from the charger at all.
Simply unplug the battery from its end. Failure to do so will create an arc in between
the leads, this will damage the battery! The Scout comes equipped with 5000 mAh 3s
LiPo batteries. The Onset comes equipped with 4000 mAh 3s LiPo batteries. It is
important that the batteries are charged with these settings. Failure to do so could
result in machine under performance or damage to the battery.
1 10 Page 9
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Precision Drone Quadcopter Handbücher
