Precision AM60 Bedienungsanleitung
INSTALLATION
GUIDE
4
o 24mm
Edgebore
Crossbore
1
56
6a
33a
22a
60mm
20mm 20mm
Ezi - t housing cups
Self Adhesive
coverplates
Self Adhesive
coverplates
Strikeplate
Strikeplate
Strikebox/drilling templateStrikebox/drilling template
Precisi n
AM6O
MAGNETIC TUBULAR LATCH
Precisi n
AM6OPV
TUBULAR PRIVACY BOLT
1. Edgebore-Drill a 24mm hole into the edge of the door at
the desired height.
Crossbore-Drill hole(s) into the face of the door at a backset
of 60mm to the diameter(s) etc specified on the chosen
handles installation instructions.
3. Drill a 3mm pilot hole into the jamb at the position
marked by the pointed Strikemarker tool.
Use the pilot hole as a guide to drill a 24mm hole into
the jamb to a depth of approx. 20mm.
2. Insert the Strikemarker tool (FIG.B) into the edgebore hole
(2A).
Close door tightly then press the pointed Strikemarker tool
into the jamb to mark a mounting position for the strikeplate.
5. Use the 3mm pilot holes in door as a guide to drill
2 x 24mm overlapping holes (above and below the edgebore
24mm hole) to a depth of approx. 5mm.
Repeat this step on the jamb to create 2 x overlapping 24mm
holes.
6. Use a blade or pencil to mark vertical lines down the
sides of the 3x overlapping 24mm holes on door and
jamb (6a).
Use a Chisel to remove timber from the sides of the
overlapping 24mm holes where marked.
8x8mm8x8mm
4. Insert the plastic Strikebox/drilling template into the
edgebore hole and use as a guide to drill 2x 3mm pilot
holes above and below edgebore hole.
Insert strikebox/drilling template into the 24mm hole
created in jamb (3a) and drill 2 x 3mm pilot holes above
and below 24mm hole.
o
o
o
o
o
o
o
o
o
o
oo
o
7 8 8a
9
10
Strikeplate
FIG. A
Latch/bolt
Strikeplate Adjustment Guide
( to reduce ‘Latch Rattle’ )
FIG. C
FINISHED PRODUCT
Latch/bolt
ADJUSTMENT TAB B
(use this side if latch fits too tightly into strikeplate)
ADJUSTMENT TAB A
(standard position)
Self Adhesive cover plate
AM60 - ITP
AM60 - ITP installation tool pack (sold separately)
FIG. B
8. Insert latch assembly into the door edgebore hole (8a) and
secure in place with screws provided. Be careful not to over
tighten screws as this may cause the flanged housing cups to
deform and/or cracking in timber. Note: screwheads must fit
below, or perfectly flush to the surface of the latch/strikeplate,
to allow coverplates to adhere properly to surface (FIG. A). Now
install chosen door handles as per manufacturers instructions.
10. Affix the 'self-adhesive' s/steel coverplates to the faces of
the latch and strikeplate for a more attractive 'concealed fix'
finish. (optional).
Note: make sure metal faces of latch and strikeplate are free
from dust /oil etc before affixing coverplates, to insure
maximum adhesion strength.
9. Insert the strikeplate assembly (incl. strikebox/drilling template)
into the prepared jamb 'cutout' so that the latch/bolt rests against
Adjustment Tab A when in the locked/latched position (FIG. C).
Secure in place with screws provided.
Test door operation and if necessary 'bend out' adjustment tab
with the AM60 ITP screwdriver (FIG.B), to reduce latch/bolt rattle.
7. Example of 'door preparation' completed - ready for the
latch/bolt to be installed.
Dieses Handbuch passt für folgende Modelle
1
Andere Precision Sperren Handbücher
