Prem-I-Air EH0468 Bedienungsanleitung

Page 1

EH0468

3.5kW (12000 BTU/hour)

Local Air Conditioner

Climatiseur Local

Page 2

IMPORTANT

Installer and Users please note:

These instructions should be read carefully and left with the user of the product

for future reference. BEFORE USE

Inspect the product including its cable and plug for any signs of damage. If the

product is damaged, DO NOT use it, and contact your supplier immediately. The

appliance contains a refrigerant gas, so must be kept upright at all times. After

unpacking wait 3 hours for the refrigerant gas to stabilise before use.

INSTALLATION

Stand the EH0468 on a firm, flat, level surface.

Connect the exhaust hose as follows: expand a small section of the end, and

screw into the indoor adaptor; then slide the indoor adaptor into the slot at the

back of the unit. Expand a small section of the other end of the hose, and screw

into the fish-tail-shaped adaptor.

Slide the two-part window adaptor to the correct length to fit the window. Close

the window as far as possible to keep the window adaptor in place. Clip the fish-

tail shaped adaptor into the obround aperture in the window adaptor.

Keep the hose as straight as possible, avoid dips where the moisture from the

exhaust air can condense and fill the tube with water. Do not allow the hose to be

crushed.

Page 3

The hose can be expanded up to 1.8 m long, but the shorter it is the more

efficiently the EH0468 will operate. Do not extend the hose, or replace with

another type of hose. Fit one CR2032 battery to the remote

control, observing the correct polarity.

Do not attempt to recharge the battery.

Do not dispose of the battery in a fire,

as it will explode.

Do not use any other type of battery.

GENERAL SAFETY REQUIREMENTS

Domestic wiring must be tested periodically by a qualified electrician at least

once every 10 years or at every change of occupancy.

For office and retail premises, and buildings such as village halls, the wiring must

be inspected at least once every 5 years.

It is recommended that all building be fitted with smoke alarms (it is mandatory

for new buildings). PRODUCT SAFETY

This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without

supervision.

Place the appliance on a firm flat surface. Ensure that the it is kept upright at

all times

Ensure that there is at least 300mm (1') between the sides of the appliance

and any flammable materials

Ensure that there is at least 900mm (3') from the top of the appliance and

any flammable materials.

Do not place on soft surfaces.

Do not cover.

Do not obstruct the air intakes and exhausts.

For indoor use only

Not suitable for use in boats, caravans or similar locations.

Do not use in bathrooms, or in wet locations.

Do not place the mains lead beneath a carpet or rug.

Page 4

Do not use the appliance in locations where paint, petrol or other flammable

liquids are used or stored.

Always transport and store in an upright position.

Do not allow the appliance to fall over when there is water in the bucket.

PAT TESTING.

When used in an office environment, this product must be safety-tested yearly by

a qualified electrician (PAT Tested) in order to comply with the Electricity at Work

Regulations.

We recommend that it is PAT tested regularly when used in a domestic

environment. OPERATION

Leave the appliance in an upright position for 3 hours before first use.

Plug the mains lead into a 13 Amp mains socket (unless permanently installed)

If connecting via an extension lead, make sure that the lead is rated at 13 Amps

or more, and that it is fully unwound.

Switch the unit on at the mains socket.

ON/OFF Button: Press the "ON/OFF" button to start the unit. The Power

indicator illuminates when the appliance is ON. There will be a short delay (of

about a minute) before the appliance starts to operate.

"MODE" Button: Select the mode by pressing the "MODE" button. The available

modes are:

Automatic mode: either heats or cools as required to maintain the

selected room temperature. Then use the TEMP+ and TEMP˜ buttons to

select the desired room temperature. When the temperature reaches the desired

temperature, the compressor will stop, and the fan will continue to run.

Cooling mode: cools if the room temperature is above the selected

temperature.Then use the TEMP+ and TEMP˜ buttons to select the

desired room temperature. When the temperature reaches the desired

temperature, the compressor will stop, and the fan will continue to run.

Dehumidifying mode: removes humidity, but does not affect room

temperature. The fan operates at its lowest speed. For best results, do not

use the exhaust tube, but fit a permanent drainage pipe to the drain outlet as

shown on page 7.

Fan mode: circulates the air, but does not affect room temperature or

humidity.

Heating mode: heats if the room is temperature is below the selected

temperature. Then use the TEMP+ and TEMP˜ buttons to select the

desired room temperature. When the temperature reaches the desired

temperature, the compressor will stop, and the fan will continue to run. Heating

performance reduces if the outdoor temperature falls below 7 °C

Page 5

"SPEED" Button: Set the fan speed using the fan speed control.

In all modes except dehumidifying mode. The fan speed can be low, medium or

high. The fan speed is indicated by the speed of the segments on the windmill

symbol on the LED display.

TEMP+ and TEMP˜ buttons:

Use the + and ˜ buttons to select the desired room temperature. The temperature

can be set to any temperature from 16 °C to 31 °C. Selecting a lower

temperature whilst heating, or a higher temperature whilst cooling will reduce

power consumption.

SWING button: Press the "SWING" button to turn the oscillation of the louvres

on or off.

If the "WATER FULL" indicator lights, the condensate

water tank is full. This should only happen very rarely, as

most of the water collected is evaporated and sent down

the exhaust air tube.

To empty the water, switch the unit off by pressing the

ON/OFF button, wait for three minutes, and then

disconnect from the mains supply. Place a drainage pan

underneath the drain outlet plug (an the bottom of the unit,

at the back in the centre). Withdraw the bung, and allow

the water to drain into the drainage pan. Replace the bung,

and reconnect the unit to the mains supply.

The water should be disposed of down a drain.

To avoid the need to empty the water,

a permanent drain tube may be fitted

as shown: use a piece of 18mm

diameter tube (not supplied) and run

the pipe to a drain, making sure that it

runs downhill all the way.

Unplug the EH0468 from the mains

when not in use.

END OF SEASON STORAGE.

Before putting the appliance into storage, empty all water from the drain, and run

the appliance on "fan only" mode for a few hours to dry the inside thoroughly.

Clean the filter, unplug the mains cable, and store the appliance in its original box

in an upright position. Remove the battery from the remote control.

Page 6

USING THE TIMER

The timer can set the unit to run for a selected time (between 1 and 24 hours)

and then turn OFF.

Or, it can set the unit to wait for a selected time (between 1 and 24 hours) before

turning ON.

To select timed turn-off press the timer button whilst the unit is switched ON.

Then adjust the time using the + and –buttons for the number of hours' delay

before switching off.

To select timed turn-off press the timer button whilst the unit is switched OFF

(connected to the mains supply but switched OFF using the ON/OFF button).

Then adjust the time using the + and –buttons for the number of hours' delay

before switching on.

To cancel the timer, press the TIMER button again.

USING THE REMOTE CONTROL

The heating, cooling, dehumidifying and fan modes are selected in exactly the

same way as using the control panel on the main unit.

OPERATING COSTS

At time of going to press, the average cost of electricity is £0.12 per unit (kilowatt-

hour). The amount you are being charged will be shown on your electricity bill.

At this cost, the EH0468 will cost £0.15 per hour to run in heating, cooling or

dehumidifying modes, and £0.05 per hour to run in the fan-only mode.

To minimise the power used (and reduce operating costs):

Make sure that the filter is kept clean.

Make sure that the air intakes and exhausts are not obstructed.

Keep doors and windows closed to prevent conditioned air from escaping,

and to prevent exhaust air from re-entering the room.

Use blinds to prevent direct sunlight reaching the room.

Set the temperature higher whilst cooling, or lower whilst heating.

MAINTENANCE

Before cleaning, turn the appliance off, and disconnect from the mains supply.

The appliance may then be cleaned using a damp cloth with a drop of washing-

up liquid to remove any dust or dirt from the case. Do no use stronger detergents

or solvents as these may damage the plastic.

Cleaning the filter:

The filter is located on the back panel of the appliance. Unclip to remove, then

remove dust and dirt using a vacuum cleaner. The filter should be cleaned every

two weeks to maintain optimum performance.

Using a dry 1" (25mm) paint-brush, remove any dust from the grilles.

If the mains lead is damaged, it must be replaced by the manufacturer or an

authorised service centre. If the mains plug needs to be replaced, proceed as

follows:

Page 7

Connect the brown wire to the terminal

labelled "L".

Connect the blue wire to the terminal

labelled "N"

Connect the green/yellow wire to the

terminal labelled with the earth symbol

or "E".

Make sure that the cord-grip is

positioned correctly (over the outer sheath of the cable) and it fully tightened.

FAULT-FINDING

If the EH0468 is not operating, proceed as follows:

Check that the mains plug is firmly in the socket, and that the socket is switched

ON.

When the unit if switched on there will be a delay of about 3 minutes before it

starts to operate.

•Unit stops running:

Mains supply is disconnected or has failed

Target temperature has been reached.

Timer has been set.

Water tank is full (WATERFULL indicator will illuminate)

•In cooling mode, no cool air is produced:

Room temperature is lower than set temperature

The unit is defrosting (this will take a few minutes, and afterwards, it will resume

operation)

Filter is blocked

•Cooling is poor on hot days

Too much direct sunshine is heating the room

Windows or doors are open allowing hot air into the room

A lot of people in the room (each person contributes about 75W of heating)

Electrical equipment in the room producing heat

•Heating is poor on cold days

The heat pump can only heat effectively when the outdoor temperature is above

7 °C

•Remote control does not work:

Check that the battery is correctly installed, and is not exhausted.

Make sure that the remote control is pointed towards the main unit when being

used. FAULT CODES

If any error codes appear on the display, contact your local service agent.

E0: Room temperature sensor failure

Page 8

DISPOSAL AND RECYCLING

You must not dispose of this appliance with domestic household waste.

Most local authorities have specific collection system for appliances and disposal

is free of charge to the end-user.

When replacing an existing appliance with a similar new appliance your retailer

may take the old appliance for disposal.

This air conditioner contains R410a refrigerant gas. At the end of its life the

disposal of this product must be in accordance with local regulations.

TECHNICAL SPECIFICATION

Dimensions: 370×400×760 mm

Weight: 27.4 kg

Power supply: 230V ~

Power consumption (cooling): 1330 W

Power consumption (heating): 1320 W

Operating current (cooling): 6.1 A

Operating current (heating): 6.0 A

Heating capacity: 3500 W

(12000 BTU/hour)

Cooling capacity: 3500 W

(12000 BTU/hour)

Dehumidifying capacity: 36 litres/day

Operating temperature (cooling): 16—32 °C

Operating temperature (heating): 7—27 °C

Air flow: 350 m3/h

Refrigerant: R410a (330 g)

Page 9

IMPORTANT

Installateurs et Utilisateurs, veuillez noter:

Ces instructions doivent être lues attentivement et conservées pour une

éventuelle future consultation.

AVANT UTILISATION

Inspectez le produit y compris le câble et la prise. Si le produit est endommagé,

NE L’UTILISEZ PAS, et contactez immédiatement votre revendeur.

INSTALLATION

Si vous utilisez le EH0468 pour chauffer ou rafraîchir la pièce, vous devez utilisez

le tuyau d’évacuation. Pour la déshumidification, le tuyau d’évacuation n’est pas

nécessaire.

Placez le EH0468 sur une surface plane, stable et de niveau.

Pour connecter le tuyau d’évacuation, élargissez un peu l’extrémité du tuyau et

vissez dedans l’adaptateur intérieur puis glissez l’adaptateur intérieur dans la

fente à l’arrière de l’appareil. Elargissez un peu l’autre extrémité du tuyau, et

vissez dans l’adaptateur en forme de queue de poisson et passez l’adaptateur

par une fenêtre ouverte.

Gardez le tuyau le plus droit possible, évitez les creux où l'humidité de l'air peut

se condenser et remplissez le tube avec de l'eau. Vérifiez que le tuyau n’est pas

écrasé.

Page 10

Le tuyau peut être étendu jusqu'à 1,80 m de long, mais plus il est court mieux

l’appareil fonctionnera. Ne rallongez pas le tuyau ou ne remplacez par un autre

type de tuyau.

Mettez une pile CR2032 dans la télécommande, en respectant la polarité.

CONSIGNES DE SECURITE

Cet appareil peut être utilisé par des enfants âgés de 8 ans et plus et par

des personnes dont les capacités physiques, sensorielles ou mentales sont

diminuées ou manquant d'expérience ou de connaissances uniquement

sous la surveillance d'un adulte qui leur aura appris à utiliser l'appareil et leur

aura expliqué les risques encourus.

Les enfants ne doivent pas jouer avec l'appareil.

Placez le EH0468 sur une surface plate et stable.

Respectez une distance minimum de 300mm entre les côtés du radiateur et

tout matériau inflammable.

Respectez une distance minimum de 900mm entre le haut de l’appareil et

tout matériau inflammable.

Ne le placez pas sur une surface molle.

Ne le couvrez pas. Un symbole situé sur le radiateur vous le rappelle.

Pour utilisation à l’intérieur uniquement.

Ne convient pas à une utilisation dans les bateaux, les caravanes ou

endroits similaires.

N’utilisez pas l’appareil dans une salle de bains ou une pièce humide.

Ne passez pas le cordon d’alimentation sous une moquette ou un tapis.

N’utilisez pas le radiateur dans des endroits où de la peinture, de l’essence

ou d’autres liquides inflammables sont utilisés ou stockés.

N’utilisez pas l’appareil sans les pieds fournis.

CONSIGNES GENERALES DE SECURITE

Le câblage doit être testé périodiquement par un électricien qualifié

au moins une fois tous les 10 ans ou à chaque changement d’occupation.

Pour les bureaux et les locaux de vente au détail ainsi que les bâtiments publics,

le câblage doit être inspecté au moins une fois tous les 5 ans.

Il est conseillé d’équiper tous les bâtiments avec un détecteur de fumée (il est

obligatoire pour les nouveaux bâtiments).

Inhaltsverzeichnis

Sprachen:

Andere Prem-I-Air Klimaanlage Handbücher

Prem-I-Air

Prem-I-Air EH0539 Bedienungsanleitung

Prem-I-Air

Prem-I-Air PKY12 Bedienungsanleitung

Prem-I-Air

Prem-I-Air KY-32/K101 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1230 Bedienungsanleitung

Prem-I-Air

Prem-I-Air KY-44B Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1924 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1922 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1413 Bedienungsanleitung

Prem-I-Air

Prem-I-Air PMINV18 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1910 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1614/EU Bedienungsanleitung

Prem-I-Air

Prem-I-Air PMSF09 Series Bedienungsanleitung

Prem-I-Air

Prem-I-Air KY32 Bedienungsanleitung

Prem-I-Air

Prem-I-Air PAC1130 Bedienungsanleitung

Prem-I-Air

Prem-I-Air ACS16E Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1768 Bedienungsanleitung

Prem-I-Air

Prem-I-Air PEVAPKY32 Bedienungsanleitung

Prem-I-Air

Prem-I-Air TC-N9KM Bedienungsanleitung

Prem-I-Air

Prem-I-Air PMSF12 Series Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1640 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1926 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1920 Bedienungsanleitung

Prem-I-Air

Prem-I-Air PREMAC20 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1544 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung