Premier Mounts RFM Bedienungsanleitung
9531-009-041-0X v6.3 publ. 05/28/19
Installation Guide
RFM
500 W Central Ave, Suite A, Brea, CA 92821 USA
Installation Guide
RFM
Page 2
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND
COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION
FOR FUTURE REFERENCE.
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY
UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS,
DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR
IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
Caution Statements
Weight Limit
Maximum Flat Panel Weight: 160 lbs.
THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FOUR TIMES THE WEIGHT OF THE DISPLAY. IF NOT, THE
SURFACE STRUCTURE MUST BE REINFORCED. THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 160
LBS. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION
INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN
DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER
SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
the display.
If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical
wires in wall. Cutting/drilling into an electrical line may cause serious injury.
Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe
water damage to the mounting surface.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact.
Installation Tools:
Pencil Protective Eyewear
Electronic Stud Finder
Level 13mm or 1/2" Socket
M6 or 1/4” Drill Bit 3/8” Masonry Drill Bit
Portable Drill
Phillips Head Screwdriver Socket Wrench
Installation Guide
RFM
Page 3
Included Components:
RFM mount may contain an Enhanced Leveling Arm and Rotational Limiter.
The Rotational Limiter with Enhanced Leveling Arm designed to limits the user from
rotating in a full 360 degrees motion, causing cables to coil around the axle.
The Rotational Limiter sets the rotation at 0° (landscape) and 90° (Portrait) orientation,
clockwise and counter-clockwise.
if the mount requires extensive servicing.
ENHANCED DESIGN FEATURES
Original
Design
Enhanced
Design
Enhanced
Leveling Arm
Rotational
Limiter
OR
Installation Guide
RFM
Page 4
Included Hardware:
5/16" x 3" Lag Bolt
(Qty.4)
M5 Security Allen
Key (Qty.1)
M4 x 16mm Comb.
Screw (Qty.4)
M6 x 30mm Comb.
Screw (Qty.4)
M8 x 16mm Comb.
Screw (Qty.4)
M8 x 25mm Comb.
Screw (Qty.4)
M8 x 30mm Comb.
Screw (Qty.4)
M4 x 25mm Comb.
Screw (Qty.4)
M4 x 30mm Comb.
Screw (Qty.4)
M6 x 16mm Comb.
Screw (Qty.4)
M6 x 25mm Comb.
Screw (Qty.4)
Universal Spacer
(Qty.8)
M6 x 12mm Button
Security (Qty.1)
M6 Lock Washer
(Qty.1)
M10 x 30mm Comb.
Screw (Qty.4)
5/16" Washer (Qty.4) Griplate™(Qty.4) Finned Anchor
(Qty.4)
Straw (Qty.1) 5/32" Allen Key
(Qty.1)
2
Remove the M6 Knurl Knob from the wall mount
and place it aside.
XX
1.
studs in the vicinity of the wall plate.
2. Use a pencil to mark the center of each of the wall
studs.
Wood Installation
1
Installation Guide
RFM
Page 5
1. Place the wall mount against the wall and align it
with the pilot hole.
2. Insert one (1) 5/16" x 3" lag bolt and one (1) 5/16"
washer into the upper right mounting hole and
tighten using a socket wrench and 1/2" socket.
1) Level the wall mount.
2) Use a pencil to mark the remaining three (3)
mounting locations along the center of each wall stud.
Drill a "pole hole" in the center of the upper right mark
using a 1/4" drill bit and power drill.
1. Place the wall mount against the wall in the
desired viewing location.
2. Use a pencil to mark the upper right mounting
location alone the center of the wall stud.
Do not over tighten the lag bolt.
5
3
6
4
Installation Guide
RFM
Page 6
1. Insert one (1) 5/16" x 3" lag bolt and one (1) 5/16"
washer into each pilot holes.
2. Tighten all lag bolts using a socket wrench and
1/2" socket.
Two people are recommended for this step: one
person to level the wall mount and another person to
mark the mounting locations.
Concrete Installation
Drill four (4) pilot holes of each mark using a drill and
3/8" masonry drill bit.
Insert the Finned Anchors into each pilot hole.
Lightly tap each Finned Anchors into place with a
hammer.
Do not over tighten the lag bolt.
2 3
7 1
Installation Guide
RFM
Page 7
1. Insert one (1) 5/16" x 3" Lag Bolt and one
(1) 5/16" washer into each pilot holes.
2. Tighten all lag bolts using a socket wrench and
1/2" socket.
Do not over tighten the lag bolt.
1) Insert a small straw or toothpick into the threaded inserts found on the
2) Use a pencil to mark the depth of the threaded insert on the small straw
or toothpick.
3) Mark the straw or toothpick 1/8” above the depth of the threaded insert,
as shown in Figure 1.
4) Insert the small straw or toothpick into the remaining threaded inserts
to compare and verify their depth using the straw or toothpick’s 1/8”
allowance mark.
5) Locate the correct diameter screw for the threaded insert.
If the screw you selected is longer than the 1/8” allowance mark on
the small straw or toothpick, as shown in Figure 2 and Figure 3, do
not use this screw. The screw length must not bypass the mark.
6) Test each size of the screws provided.
The correct screws should thread easily into themounting point and
not pull out when tension is applied.
Small Straw or Toothpick
Marking the 1/8”
Allowance
Small Straw
or Toothpick
Small Straw
or Toothpick Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
Selecting the Mounting Hardware
4
Installation Guide
RFM
Page 8
Slide the mounting brackets into the cross bar.
Align the brackets to the display mounting holes. Use the depth measuring straw to determine
the appropriate hardware. Use four (4) M4, M6, or M8 screws depending on display and four
(4) Griplate™ (Universal Washer). Use Universal Spacer if necessary.
Bottom
Top
M4, M6, or M8 screws
Griplate™ (Universal Washer)
Universal Spacer (Optional)
Top of display
Bottom
Rotational Support
(Top of display)
1
2
Installation Guide
RFM
Page 9
M8 x 10mm Set Screw
C
L
Center the cross bar to the display and tighten the two (2) M8 x 10 Set Screws using the
5/32" Allen Key to secure the brackets.
Two or three person is recommended for this step. Lift the cross bar and place it into the wall mount..
3
4
Installation Guide
RFM
Page 10
Install the M6 Knurl Knob removed from step 1 to secure the cross bar from dislodging.
Tension
Screw
THE MOUNT IS READY TO USE.
SEE NEXT PAGE IF INSTALLED WITH ROTATIONAL LIMITER.
5
6
Andere Handbücher für RFM
1
Inhaltsverzeichnis
Andere Premier Mounts TV-Halterung Handbücher
Premier Mounts
Premier Mounts AM500-U Bedienungsanleitung
Premier Mounts
Premier Mounts PRF-100 Bedienungsanleitung
Premier Mounts
Premier Mounts POH46-EX Bedienungsanleitung
Premier Mounts
Premier Mounts ECM-D70T Bedienungsanleitung
Premier Mounts
Premier Mounts AM100 Bedienungsanleitung
Premier Mounts
Premier Mounts CTM-MS4 Bedienungsanleitung
Premier Mounts
Premier Mounts Rotary series Bedienungsanleitung
Premier Mounts
Premier Mounts CTM-MS3 Bedienungsanleitung
Premier Mounts
Premier Mounts 7170-0978 Series Bedienungsanleitung
Premier Mounts
Premier Mounts PCM-MS2 Bedienungsanleitung
Premier Mounts
Premier Mounts INW-42 Bedienungsanleitung
Premier Mounts
Premier Mounts RTM-S Bedienungsanleitung
Premier Mounts
Premier Mounts CTM-200 Bedienungsanleitung
Premier Mounts
Premier Mounts FPS-300 Bedienungsanleitung
Premier Mounts
Premier Mounts PTFM3765 Bedienungsanleitung
Premier Mounts
Premier Mounts PCB-CSL1 Bedienungsanleitung
Premier Mounts
Premier Mounts PSD-TTS/B Bedienungsanleitung
Premier Mounts
Premier Mounts MM-EP15 Bedienungsanleitung
Premier Mounts
Premier Mounts ECM-3763Q Bedienungsanleitung
Premier Mounts
Premier Mounts AM95 Bedienungsanleitung
