Prestige APS-687TWE Bedienungsanleitung

128-9446

1 of 12

Page 1

APS-687TWE

Owners Guide

Deluxe 7 Channel LED

Remote Start System

With Keyless Entry

PATENTED: www.voxxintlcorp.com/company/patents

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference that may

cause undesired operation.

Warning!

Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment

NOTE:The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modications to this equipment. Such modications could void the

user’s authority to operate the equipment

Table Of Contents:

Features and Options Page 2

Your "Spread Spectrum" Transmitters Page 3

Keyless Entry Page 3 - 4

Optional Remote Function Channels Page 4

Optional Additional Remote Channel 4 Page 4

Optional Additional Remote Channel 5, 6, 7 Page 5

Valet Override, Programming & Safety Control Switch Page 6

Vehicle Service / Remote Start Override Mode Page 6

Turbo Timer Operation Page 6 - 7

Remote Starting The Vehicle Page 7 - 8

Automatic Start Timer Operation Page 9 - 10

Telematic Upgrade Page 10

Programmed Transmitter Notication (PTN) Page 10

Programming New or Replacement Transmitters Page 11

Features And Function Setting Chart Page 12

128-9446

2 of 12

Page 2

Deluxe 7 Channel LED Remote Start System

With Keyless Entry

FEATURES :

1 Five Button LED Programmable RF Transmitters

1 Five Button Programmable RF Transmitters

 Seven Channel Receiver (capable of accepting 4 transmitters)

Code Hopping Technology

 External Superheterodyne Antenna w/PushButton Switch and LED

 Safe Start RF Control (Double Push Of RF Transmitter)

Selectable Automatic Timed Start Mode

 Keyless Entry Outputs (-)

On-Board Start Relay

On-Board Accessory Relay

3 On-Board Ignition Relays

On-Board Parking Light Relay

Ignition 2 and 3 Relay Selectable On or Off During Cranking

Ground Output While Running / Shock By-Pass / GM VAT Output

Tach Signal Learning Circuit

 Two ( + ) and Two ( - ) Safety Shutdown Circuits

Alarm By-Pass Output

 Channel 3 Output for Remote Trunk Release (relay required)

Channel 4, 5, 6, and 7 Output to Control Optional Accessories

Selectable Steady or Flashing Parking Lights for Run Indication

Selectable Run Times

Selectable Door Lock Output Pulse Timing

 Optional Illuminated Entry Output (Relay Required)

Vehicle Horn Activation Output For R/S Annunciation

 External Activation Control Input

Turbo Timer Mode

OPTIONS:

Telematic Upgrade Ready

Plug In Flash Logic By-Pass Capable

Remote Power Window Control

Multiple Vehicle Capable

WARNING! Be certain that the vehicle is outdoors before using this or any

remote vehicle starting device. A running engine produces

dangerous carbon monoxide fumes which can be harmful or fatal

if prolonged exposure occurs.

DO NOT remote start the vehicle if the car is garaged.

128-9446

3 of 12

Page 3

1 2

YOUR “SPREAD SPRECTUM" TRANSMITTERS

The transmitters included with your new security

system use the most advanced and secure form

of radio frequency transmission available on any

current automotive security system. Some of today’s

sophisticated auto thieves use a device known as a

code grabber, which will receive and store the signal

from your keychain transmitter and re-transmit at a

later time to disarm your system.

Your Spread Spectrum transmitters will shift frequencies making it impos-

sible for a theif to grab and rebroadcast your code.

If your transmitter button is pressed more than fty times while it is out of

range of the vehicle (children playing with your keys), the transmitter will

not operate when you return to the vehicle, and will need to be re-aligned

to the receiver. To do this, simply press the lock/unlock button two times

within a one second time period. The system will now respond to that

transmitter each time a button is pressed.

For reference the transmitter packaged with your system may not appear

exactly as shown This depiction is for reference only.

NOTE: As an option, this system has the ability to operate the vehicle's

horn which may require some additional parts. If this feature is installed,

the vehicle's horn will beep once when you lock the doors, twice when you

unlock the doors, twice when the Remote Start feature is activated, and

will beep during the car nder mode to allow you to nd the vehicle more

easily in a crowded parking lot.

THE LED TRANSCEIVER:

Shown above right, will respond with an LED ash when any command is

issues. Press the lock button, and when the vehicle receives the command,

it will report back that the function was executed by ashing the correspond-

ing LED, Lock, Unlock, Trunk, or in the case of Remote Start the LED will

ash once every 10 seconds while the vehicle is running under it's control.

KEYLESS ENTRY

1. To lock your vehicle, exit the vehicle, close all doors, hood and trunk,

then simply press the lock button of your keychain transmitter. To unlock

your vehicle, simply press the unlock button of your keychain transmitter.

As a keyless entry unit, for your convenience, the parking lights will ash

128-9446

4 of 12

Page 4

once when the doors are locked and twice when the door are unlocked.

If the optional illuminated entry feature has been added, the interior light

will turn on when the doors are unlocked and remain on for 30 seconds or

until the ignition is turned on.

Holding the lock/unlock transmitter button for 3 seconds will activate the

car nder mode causing the parking lights to ash and the optional horn to

beep for 30 seconds Activating these button's a second time for 3 seconds.

or pressing any other transmitter button while the car nde mode is active

will cancel this mode.

NOTE: This system has the ability to unlock the drivers door with the rst

press of the unlock transmitter button and then unlock all other

doors when the unlock button is pressed a second time. This op-

tional feature may require additional components. Consult your

installation center to determine if this feature has been added

to your vehicle. Additionally this system can be programmed to

automatically lock and unlock the doors with the turning on and

off of the ignition key.

ADDITIONAL REMOTE FUNCTION (CHANNEL 3)

This system has an additional feature that can be connected to a number

of different optional accessories. Some of the more common uses for this

channel are:

Remote Trunk Release

Remote Window Closure

Remote Garage Door Interface

To activate the optional accessory, press and hold the trunk/key button on

the keychain transmitter for four seconds.

NOTE: The feature that has been added to channel 3 will always be

activated using the same transmitter button that remotely starts

the vehicle. There is no way to move the channel 3 function to a

different transmitter button.

ADDITIONAL REMOTE FUNCTION (CHANNEL 4)

This system has an additional feature that can be connected to a number

of different optional accessories. Some of the more common uses for this

channel are:

Can Be Set Up To Activate Rear Window Defogger

During Remote Start If Vehicle Is So Equipped

Remote Window Closure

Rear Hatch Release

128-9446

5 of 12

Page 5

Right Or Left Slider Doors in An Equipped Van

To activate the optional accessory, press the option button on the key-

chain transmitter. The optional accessory will immediately engage.

ADDITIONAL REMOTE FUNCTION (CHANNEL 5)

This system has an additional feature that can be connected to a number

of different optional accessories. Some of the more common uses for this

channel are:

Remote Trunk Release

Remote Window Closure

Rear Hatch Release

Right Or Left Slider Doors in An Equipped Van

To activate the optional accessory, press the option button on the key-

chain transmitter. The optional accessory will immediately engage.

ADDITIONAL REMOTE FUNCTION (CHANNEL 6)

This system has an additional feature that can be connected to a number

of different optional accessories. Some of the more common uses for this

channel are:

Rear Hatch Release

Right Or Left Slider Doors in An Equipped Van

Driver Priority Settings In Vehicles So Equipped

To activate the optional accessory, press the option button on the key-

chain transmitter. The optional accessory will immediately engage.

ADDITIONAL REMOTE FUNCTION (CHANNEL 7)

This system has an additional feature that can be connected to a number

of different optional accessories. Some of the more common uses for this

channel are:

Rear Hatch Release

Right Or Left Slider Doors in An Equipped Van

Driver Priority Settings In Vehicles So Equipped

Second Driver Priority Settings In Vehicles So Equipped

128-9446

6 of 12

Page 6

To activate the optional accessory, press the option button on the key-

chain transmitter. The optional accessory will immediately engage.

NOTE: If your system utilizes the transmitter shown, the second option

button may be congured to operate additional accessories.

Please consult your installing retailer for more information concerning

the options available.

PUSH-BUTTON LED RECEIVER

VALET/OVERRIDE/SAFETY CONTROLSWITCH

The Push-Button LED switch located in the receiver allows you to

temporarily disable the remote starting function of the system. This is

recommended whenever the vehicle is being serviced.

To place the system in the service mode:

1) With the system disarmed/unlocked, and the ignition switch off, Press

and Hold the Push-Button, found on the windsheild receiver, in.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED begins to ash two short ashes followed by one long

ashes and continues this pattern until returned to normal mode of

operation.

This means the unit into the R/S Override mode indicating that the re-

mote start is in the service mode and will not start from RF or any other

input Car Connection, Car Link or otherwise.

To exit the service mode:

1) With the system disarmed, Press and Hold the Push-Button, found on

the windsheild receiver, in.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED turns off indicating that the R/S unit is fully functional one

again.

TURBO TIMER MODE

This system provides a means to cool down the vehicles turbo charger,

if so equipped, by allowing the vehicle to continue to run for a prescribed

period of time every time the vehicle's engine is turned off. This feature

requires the system to be set up for turbo timer during installation. Con-

sult with your installation center to be certain this feature was activated

128-9446

7 of 12

Page 7

and how long the vehicle will continue to run, 3, 5, or 10 minutes after the

ignition switch is turned off.

TO ACTIVATE THE TURBO TIMER

Anytime the ignition key is in the on position for more than 15 seconds:

1) Place the gear selector in park.

2) Set the parking, (hand), brake.

3) Be certain your foot is off the brake pedal.

4) Press the receiver's program/Push-Button switch 2 times within 5

seconds. The parking lights will ash two times indicating the mode was

successfully entered.

If your parking lights ashed four times, this indicates the turbo mode was

on and is now turned off.

With the turbo timer mode selected on, after you've arrived at your

destination, while the engine is still running, set the parking brake, pause

2 seconds, then turn the ignition switch to the off position. The engine will

continue to run the allotted time according to the selection during

installation.

If you do not want the vehicle to continue to run for one cycle, simply step on

the vehicle's brake, release the parking brake, or activate the transmitter's

start button two times in succession.

Any of these will cause the engine to turn off.

REMOTE STARTING THE VEHICLE

The system WILL NOT start the vehicle if any one of the following condi-

tions exists:

1. The Vehicle Hood Is Opened.

2. The Gear Selector Is In Any Gear Other Then Park.

3. The Brake Is Depressed.

4. The System is in the remote start override mode.

128-9446

8 of 12

Page 8

WARNING! Be certain that the vehicle is outdoors before using this or

any remote vehicle starting device. A running engine produces

dangerous carbon monoxide fumes which can be harmful

or fatal if prolonged exposure occurs.

DO NOT remote start the vehicle if the car is garaged.

TO REMOTE START THE VEHICLE

Press and release the trunk/key button of your keychain transmitter two

times within 2 seconds.

The vehicle will start and remain running for the pre-programmed time

selected.

As a visual indication, the parking lights will ash or turn on dependent on

the programming set up by your installation center.

When using the LED transmitter, the LED along side the start button will

ash every 10 seconds while the vehicle is running under control of the

remote start.

When you arrive at your vehicle, unlock it with the key or by pressing and

releasing the unlock button of your keychain transmitter.

Enter the vehicle and turn the ignition key to the on position.

CAUTION! Do not turn the key to the start position. This will cause the

starter motor to engage with the already running engine which

could result in damage. Step on the brake pedal to disengage

the remote start unit. The vehicle will continue to run but now

on it's own power.

NOTE: The engine will stop running before the expiration of the

pre-programmed run timer or if you complete any of the following:

1. Press and release the trunk/key button of your keychain transmitter

two times within 2 seconds.

2. Depress the brake pedal.

3. Open the hood.

4. Place the system in Remote Start Override Mode

5. Race the engine to above 4000 RPM.

128-9446

9 of 12

Page 9

OPERATING ON AUTOMATIC START UP TIMER MODE

The system has the ability to automatically start the vehicle every 2 or 4

hours over a 48 hour period. This feature is especially useful in cold

climates where the only means to keep the engine and engine uids warm

is to periodically start the engine.

WARNING! Be certain that the vehicle is outdoors before using this

or any remote vehicle starting device. A running engine

produces dangerous carbon monoxide gases which can be

harmful or fatal if prolonged exposure occurs.

DO NOT remote start the vehicle if the car is garaged.

TO BEGIN THE AUTOMATIC START UP TIMER

1. Turn the ignition key on then off.

2. Within 10 seconds, activate the RF start command two times. (Push the

second channel button of your keychain transmitter 4 times).

The parking lights will ash 4 times indicating the timed start mode is

activated.

The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for

the pre-programmed run time, then shut off.

This will continue for 48 hours.

NOTE: The automatic start up timer can also be initiated from the

keychain transmitter.

To do this:

1. Start the vehicle using the keychain transmitter by pressing and

releasing the trunk/key button transmitter button 2 times.

2. Shut off the vehicle using the keychain transmitter by pressing and

releasing the trunk/key transmitter button 2 times.

3. Within 10 seconds of step 2, activate the RF start command two

times.

(Push the trunk/key button of your keychain transmitter 4 times).

128-9446

10 of 12

Page 10

The parking lights will ash and the siren will chirp 4 times indicating the

timed start mode is activated.

CANCELING THE AUTOMATIC START UP TIMER

To cancel the automatic start up timer do one of the following;

1. Start the vehicle manually with the use of the ignition key and depress

the brake pedal.

2. Remote start the vehicle using your keychain RF transmitter.

3. Shut off the vehicle using the keychain transmitter by pressing and

releasing the trunk/key transmitter button 2 times.

TELEMATIC UPGRADE:

This system has the ability to have a telematic upgrade module connected

to it. This is an upgrade that can give you control of certain functions of your

vehicle from a Telephone, or in some cases a computer interface. Please

check with your installation center for most recent Telematic Upgrades.

If you had a Telematic Upgrade installed, the manual supplied with the

upgrade unit will provide a operators manual advising of the features of

the system and means available to control these features of your vehicle.

PROGRAMMED TRANSMITTER NOTIFICATION (PTN)

Every time after Disarm when the ignition key is turned on, the unit's

LED will report the number of transmitters programmed into the system.

This safety feature will alert you if an unauthorized transmitter has been

programmed into your vehicle's security system without your knowledge.

Typical from the factory, there will be a 2 ash, pause, repeated 3 times

indicating that two transmitters are programmed into the system. If you

note additional ashes, there may heve been an additional transmitter

added without your knowledge or authorization. If you notice a change

in the transmitter LED report pattern, you can correct this by looking up

how to erase and reprogram your transmitters found in the transmitter

programming guide. This reprogram operation will erase all unauthorized

or unwanted transmitters.

Andere Handbücher für APS-687TWE

Inhaltsverzeichnis

Andere Prestige Fernstartsystem Handbücher

Prestige

Prestige APS-45C Bedienungsanleitung

Prestige

Prestige Platinum+ APS-875 Bedienungsanleitung

Prestige

Prestige Prestige 07S3BP Bedienungsanleitung

Prestige

Prestige Prestige 128-8115 Bedienungsanleitung

Prestige

Prestige Platinum+ APS 786 Bedienungsanleitung

Prestige

Prestige APS-57 Bedienungsanleitung

Prestige

Prestige APS57TM Installations- und Betriebsanleitung

Prestige

Prestige APSRS Bedienungsanleitung

Prestige

Prestige APS787Z Bedienungsanleitung

Prestige

Prestige APS901TWE Bedienungsanleitung

Prestige

Prestige APSRS1Z Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8541 Bedienungsanleitung

Prestige

Prestige PLATINUM APS-901C Bedienungsanleitung

Prestige

Prestige Platinum+ APS 685 Bedienungsanleitung

Prestige

Prestige APS-997EC Bedienungsanleitung

Prestige

Prestige APS-620N Bedienungsanleitung

Prestige

Prestige APSRS Installations- und Betriebsanleitung

Prestige

Prestige Platinum APS-787 Bedienungsanleitung

Prestige

Prestige Platinum APS-787a Bedienungsanleitung

Prestige

Prestige APS901 - Car Prestige Remote Start Bedienungsanleitung

Prestige

Prestige SS6900 Bedienungsanleitung

Prestige

Prestige Prestige 128-8613 Bedienungsanleitung

Prestige

Prestige APS-55C Bedienungsanleitung

Prestige

Prestige APS57Z Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung

Schumacher

Schumacher INSTANT POWER IP-75C Bedienungsanleitung