Prevelo Alpha Zero Bedienungsanleitung
1
OWNER’S MANUAL
ENGLISH
™
2
3
CONTENTS
WELCOME 5
ALPHA ZERO ASSEMBLY 6
ALPHA ONE AND ALPHA TWO ASSEMBLY 8
ALPHA THREE AND ALPHA FOUR ASSEMBLY 12
ZULU THREE AND ZULU FOUR ASSEMBLY 18
BIKE FIT 23
PRE-RIDE CHECK 24
BASIC SAFETY 25
USE AND DESIGN 28
MAINTENANCE & CARE 29
4
IMPORTANT
This manual contains important safety, performance and service information.
Read it before you take the first ride on your new bicycle, and keep it for
reference.
Additional safety, performance and service information for specific
components such as suspension or pedals on your bicycle, or for accessories
such as helmets or lights that you purchase, may also be available. Make sure
that you have obtained all the manufacturers’ literature that was included with
your bicycle and/or accessories. In case of a conflict between the instructions in
this manual and information provided by a component manufacturer, always
follow the component manufacturer’s instructions. If you have any questions
or do not understand something, take responsibility for your safety and consult
with your dealer or the bicycle’s manufacturer.
NOTE: This manual is not intended as a comprehensive use, service, repair or
maintenance manual. Please consult a bicycle professional or contact us at
(805) 557-8300 or www.prevelobikes.com for questions about repairs and
maintenance.
5
Congratulations on the purchase of your new Prevelo Bike! Excited yet? There are
just a few steps needed before your little cyclist can begin a lifelong cycling journey.
• JOIN the Prevelo Bikes Family on our Facebook page at
facebook.com/prevelobikes. This can ensure you stay up to date on any news
and special events. It’s also a great way to share pictures of your kiddos being
awesome little cyclists!
• READ this Owner Manual in its entirety. For additional information, you can also
reference our website, prevelobikes.com.
• ASSEMBLE your new bike per the Assembly Instructions included with your bike.
Don’t worry, it’s super easy.
WELCOME
6
ALPHA ZERO ASSEMBLY
Step 1: Attach Handle Bar to Stem
Using the supplied 5mm hex
key, unscrew the four bolts
holding the stem face plate to
the stem and remove the stem
face plate.
Position the handlebars on the
stem. Center the handlebars.
Make sure the cables are on the
front of the bike as illustrated.
Reattach the stem face plate
with the four bolts. Use the
supplied 5MM wrench to tighten
firmly (6NM of torque).
NOTE: Tighten the bolts in
an X pattern as illustrated.
As you tighten, pay attention
to the gap between the stem
and stem face plate. The gap
on the top should be even
with the gap on the bottom.
Alpha Zero Recommended for ages 1½ to 4
years. Adult assembly required.
7
ALPHA ZERO ASSEMBLY
Step 2: Adjust Seat Height
Release the seat tube quick release by
pulling the lever to the right side of the bike.
Adjust the seat height.
Close the quick release lever completely.
NOTE: If the seat post clamp is either too
tight or too loose, adjust tightness using
the bolt on the left side of the clamp.
For balance bike fit, Prevelo recommends
the seat height be adjusted so, while
seated in the saddle, the rider can get
both feet flat on the ground with a slight
bend in the knee.
8
ALPHA ONE AND ALPHA TWO ASSEMBLY
Step 1: Attach Handle Bar to Stem
Using the supplied 5mm hex
key, unscrew the four bolts
holding the stem face plate to
the stem and remove the stem
face plate.
Position the handlebars on the
stem. Center the handlebars.
Make sure the cables are on the
front of the bike as illustrated.
Reattach the stem face plate
with the four bolts. Use the
supplied 5MM wrench to tighten
firmly (6NM of torque).
NOTE: Tighten the bolts in
an X pattern as illustrated.
As you tighten, pay attention
to the gap between the stem
and stem face plate. The gap
on the top should be even
with the gap on the bottom.
9
ALPHA ONE AND ALPHA TWO ASSEMBLY
Step 2: Attach Pedals
Screw the pedals into the pedal
holes in the crank arms and
tighten with the supplied 15mm
wrench.
NOTE: The pedals come
labeled with “R” and “L”
stickers to indicate right and
left. The left pedal is reverse
threaded and must be turned
counterclockwise to tighten.
10
ALPHA ONE AND ALPHA TWO ASSEMBLY
Step 3: Adjust Seat Height
Release the seat tube quick release by
pulling the lever to the right side of the bike.
Adjust the seat height.
Close the quick release lever completely.
NOTE: If the seat post clamp is either too
tight or too loose, adjust tightness using
the bolt on the left side of the clamp.
For advice on seat height, please see the
fit guide on page 23.
Inhaltsverzeichnis
