Primare A30.2 Bedienungsanleitung
>
i
Primare A30.2 Amplifier User Guide
§0 Preface 18/12/00, 5:27 pm1
>Preface
ii
COPYRIGHT AND ACKNOWLEDGMENTS
Copyright © 2000 Primare Systems AB. All rights reserved.
Primare Systems AB
Idavägen 17D
SE-352 46 Växjö
Sweden
The information in this guide is believed to be correct as of the date of
publication. However, our policy is one of continuous development and so the
information is subject to change without notice, and does not represent a
commitment on the part of Primare Systems AB.
Primare is a trademark of Primare Systems AB. All other product names are
trademarks or registered trademarks of their respective owners.
Warning: To prevent fire or shock hazard, do not expose this unit to rain or
moisture.
Dangerous voltages inside. Do not open the cabinet. There are no user
serviceable parts inside. Repairs should be carried out by qualified service
personnel only.
FCC Warning: This equipment generates and can radiate radio frequency
energy and if not installed and used correctly in accordance with our
instructions may cause interference to radio communications or radio and
television reception. It has been type-tested and complies with the limits set out
in Subpart J, Part 15 of FCC rules for a Class B computing device. These limits
are intended to provide reasonable protection against such interference in
home installations.
EEC: This product has been designed and type-tested to comply with the limits
set out in EN55013 and EN55020.
This guide was produced by Human-Computer Interface Ltd,
http://www.interface.co.uk
§0 Preface 18/12/00, 5:27 pm2
>
iii
Contents
Introduction
WELCOME TO THE A30.2 AMPLIFIER ........... (1
USING THE A30.2 WITH OTHER PRIMARE
PRODUCTS................................................................ (2
TECHNICAL SPECIFICATION............................. (2
Connecting the A30.2 Amplifier
BACK PANEL CONNECTIONS........................... (3
POWER CONNECTION........................................ (4
OUTPUTS ................................................................... (4
INPUTS....................................................................... (4
Index
§0 Preface 18/12/00, 5:27 pm3
>Preface
iv
§0 Preface 18/12/00, 5:27 pm4
>
1
Introduction
Welcome to the Primare A30.2 Amplifier! This chapter introduces you to its key
features, and explains how you can take advantage of its impressive power
handling and superb sound in your system.
WELCOME TO THE A30.2 AMPLIFIER
The A30.2 is a modular power amplifier designed as the ideal output stage in
a home theatre or hi-fi system.
Modular design
The A30.2 is designed as two independent blocks, each with a separate
transformer and power supply, for the ultimate in stability and channel
separation.
Generous power handling
Each section of the A30.2 delivers 120 Watts into 8Ω, giving sufficient power
reserves for home cinema or the reproduction of recorded music. An over-
dimensioned heat sink gives excellent thermal dissipation.
Superb quality
The A30.2 delivers its power at an outstanding quality level, making it as
suitable for reproducing high quality recorded music as for home cinema. The
A30.2 also provides the option of balanced XLR inputs, for extremely low
noise when used in conjunction with a preamplifier that provides balanced
outputs.
Remote power on/off
For convenience the A30.2 can be powered on and off via a remote link
cable, avoiding the need to switch it on or off separately from the preamplifier
in the system.
USING THE A30.2 WITH OTHER PRIMARE
PRODUCTS
Although the A30.2 is flexible enough to act as the output stage in virtually
any system, it is ideal for use with other products in the Primare range, such as
the Primare P30 Processor. The A30.2 can be used as a building block in
conjunction with the Primare A30.3 and A30.5 to create modular systems with
any desired number of matched output stages, and one or more A30 Series
amplifiers can be powered on or off remotely from a P30 using the remote link
connections.
§1 Introduction 18/12/00, 5:28 pm1
>Introduction
2
TECHNICAL SPECIFICATION
Output power per channel 120W into 8Ω, 200W into 4Ω
Output impedance <0.03Ω
Line inputs 1V for 120W into 8Ω
XLR inputs 2V for 120W into 8Ω
Input impedance 11kΩ
Frequency response <10Hz – 100kHz, -3dB
THD <0.08%
Signal-to-noise, line -100dB
Power consumption 800W
Dimensions (WxDxH) 430 x 385 x 100mm
Weight 16kg
§1 Introduction 18/12/00, 5:28 pm2
>
3
Connecting the A30.2 Amplifier
This chapter explains how to connect the A30.2 to the other components in your
system, using the connections on the back panel.
BACK PANEL CONNECTIONS
]D Right XLR balanced input.
]E Right phono input.
]F Remote link sockets.
]A Right loudspeaker outputs.
]B Remote link switch.
]C Left loudspeaker outputs.
]G Left phono input.
]H Left XLR balanced input.
]I Mains power input and fuse.
RIGHT SPEAKER
+ –
LEFT SPEAKER
– +
RIGHT INPUTS
REMOTE SW
REMOTE LINK
LINK
LEFT INPUTS
]D ]E ]F ]H]G ]I
]C]B]A
§2 Connecting 18/12/00, 5:28 pm3
>Connecting the A30.2 Amplifier
4
POWER CONNECTION
Warning: Before connecting power check that the required supply voltage,
indicated on the back panel, corresponds to your local AC supply. If a
different voltage is stated on the type plate do not connect the amplifier to the
mains power, and seek advice from your dealer.
Connect the mains power using the enclosed mains cable.
Note: Always disconnect the amplifier from the mains power before
connecting or disconnecting any of the cables.
OUTPUTS
Loudspeaker outputs
Connect the left and right loudspeakers to the corresponding terminals. The
terminals can accept speaker cables terminated with 4mm banana plugs,
spade terminals, or bare wires. To connect bare wires unscrew the terminal,
pass the bare wire through the hole in the terminal bolt, and clamp the wire in
place by screwing the terminal back down.
INPUTS
Connect the A30.2 to the preamplifier or processor using either the left and
right phono inputs, or the left and right XLR inputs. If you are using the phono
inputs use high quality stereo phono leads. If you are using the XLR inputs use
balanced XLR cables.
REMOTE LINK
To power the A30.2 on and off remotely from a Primare P30 Processor
connect the REMOTE output from the P30 Processor to one of the REMOTE
LINK sockets on the A30.2, using a twin core cable terminated in 3.5mm jack
plugs. The second REMOTE LINK socket can be used to daisy-chain the
remote output to further A30 series amplifiers.
To use the remote link switch the REMOTE SW switch to the LINK position.
§2 Connecting 18/12/00, 5:28 pm4
>
5
Index
B
back panel connections ............................ 3
balanced inputs ....................................... 4
C
connections ............................................. 3
I
inputs...................................................... 4
O
outputs .................................................... 4
loudspeakers ...................................... 4
P
P30 Processor, use with ............................ 4
R
remote link .............................................. 4
REMOTE switch ....................................... 4
T
technical specification .............................. 2
X
XLR inputs ............................................... 4
§3 Index 18/12/00, 5:28 pm5
>Index
6
§3 Index 18/12/00, 5:28 pm6
Andere Handbücher für A30.2
1
Inhaltsverzeichnis
Andere Primare Verstärker Handbücher
Primare
Primare I30 Bedienungsanleitung
Primare
Primare SPA23 Bedienungsanleitung
Primare
Primare I15 Bedienungsanleitung
Primare
Primare A35.8 Bedienungsanleitung
Primare
Primare PRE35 Bedienungsanleitung
Primare
Primare R35 Bedienungsanleitung
Primare
Primare SPA20 Bedienungsanleitung
Primare
Primare A60 Bedienungsanleitung
Primare
Primare SPA21 Bedienungsanleitung
Primare
Primare SPA22 Bedienungsanleitung
Primare
Primare I21 Bedienungsanleitung
Primare
Primare A31.2 Bedienungsanleitung
Primare
Primare R32 Bedienungsanleitung
Primare
Primare A32 Bedienungsanleitung
Primare
Primare PRE35 Bedienungsanleitung
Primare
Primare A31.2 Bedienungsanleitung
Primare
Primare SP32 Bedienungsanleitung
Primare
Primare PRE60 Bedienungsanleitung
Primare
Primare A20 Bedienungsanleitung
Primare
Primare A10 Bedienungsanleitung
