Primetech PXG130SP Bedienungsanleitung
1
PRIMETECH ENGINEERING
1/43
RoHS
Operation Manual
Ver. 1.0
SWIR 1.3M/0.3M (Black & White)
GigE Vision compatible
Primetech Engineering Corp.
Model
PXG130SP / PXG130S
PXG030SP / PXG030S
2
PRIMETECH ENGINEERING
2/43
Introduction
Thank you for your purchase of the Primetech Engineering product.
We ensure that you will enjoy this and other products from Primetech Engineering for many years.
Keep this manual and warranty card handy for future reference.
For Safe Use of the Product
To ensure the safe use of this product, carefully read the warnings and cautions provided below prior to use:
Warning
Failure to follow the warning message may result in death or serious injury.
Caution
Failure to follow the caution message may result in injury or property damage.
Warning – Safety Precautions –
Never disassemble or modify the product.
Do not touch the connection cable pins or metal parts with wet hands.
Do not use the product in a place exposed to rain or water droplets or where toxic gases (liquids) are generated
nearby.
If the product will not be used for an extended period of time, unplug the connection cable from the camera.
When installing, inspecting or handling the product in a high place, implement sufficient measures beforehand to
prevent the device and parts from falling.
If you see smoke, smell a bad odor or hear an abnormal noise, immediately turn off the power supply and
unplug the cable from the product.
Do not use this product in a system that may cause a serious accident if the product exhibits an abnormality.
Caution – Precautions on Use –
■Use the product within the operating temperature range (0 to +35°C).
■Use the product at the specified power-supply voltage (+12 VDC).
■Avoid any strong impact or vibration to the product.
■Provide sufficient space around the installed product to prevent the product's internal temperature from rising.
■If the product is used in a dusty environment, be sure to implement dust-protection measures.
■Be sure to turn off the power supply after the cable has been unplugged and then plugged in again with the
power on.
■Dust and smudges on the surface of the cover glass will appear as black stains on the image. Blow away any
dust with air, etc., and wipe off any smudges using a cotton swab moistened with ethyl alcohol.
When cleaning smudges, be careful not to scratch the surface of the cover glass.
■Do not share the power supply with a motor or other type of noise-generating device.
■The SG (signal ground) and FG (frame ground) are connected inside the camera. Design the system in such a
way as to prevent the looping caused by ground potential difference.
■Do not turn off the camera power supply while rewriting the contents of the built-in memory.
Supplemental Note
■ By using it after the sensor temperature becomes constant after turning on the power, it is possible to capture
more stable images.
3
PRIMETECH ENGINEERING
3/43
Disclaimer
Primetech Engineering shall assume no responsibility for the following under any circumstance:
■Loss arising from fire, earthquake, a man-made disaster or an act of God; willful or accidental misuse of the
product; or use of the product by a third party in an abnormal manner;
■Loss arising from repair or modification performed by the customer;
■Incidental loss (lost business profit, suspension of business, etc.) arising from the use of or inability to use the
product; and
■Loss arising from malfunction, etc., caused by the combined use of connected devices.
FCC Statement
This Device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
4
PRIMETECH ENGINEERING
4/43
Revision History
Revision
Date of revision
Description of change
1.0 2021/8/6 Released the initial version.
5
PRIMETECH ENGINEERING
5/43
Table of Contents
1.
Overview................................................................................................................................................................... 7
1.1.
Characteristics ........................................................................................................................................................ 7
2.
System Configuration ............................................................................................................................................... 9
2.1.
Included contents.................................................................................................................................................... 9
2.2.
Items to be prepared by the customer .................................................................................................................... 9
2.3.
Items to be prepared by the customer as needed................................................................................................. 10
2.4.
System configuration example .............................................................................................................................. 10
3.
Specifications of Camera Parts............................................................................................................................... 11
3.1.
Front/Top/Bottom/Side .......................................................................................................................................... 11
3.2.
Rear panel ............................................................................................................................................................ 12
3.3.
Cable connection .................................................................................................................................................. 13
3.4.
FAN....................................................................................................................................................................... 13
3.5.
GPIO signal specifications .................................................................................................................................... 14
4.
Detail of function ..................................................................................................................................................... 15
4.1.
DeviceControl ....................................................................................................................................................... 15
4.2.
ROI ....................................................................................................................................................................... 15
4.3.
Decimation ............................................................................................................................................................ 16
4.4.
Reverse ................................................................................................................................................................ 16
4.5.
PixelFormat........................................................................................................................................................... 16
4.6.
TestPattern............................................................................................................................................................ 17
4.7.
AcquisitionControl ................................................................................................................................................. 18
4.8.
TriggerControl ....................................................................................................................................................... 19
4.9.
ExposureControl ................................................................................................................................................... 21
4.10.
DigitalIOControl..................................................................................................................................................... 22
4.11.
Gain ...................................................................................................................................................................... 23
4.12.
BlackLevel............................................................................................................................................................. 23
4.13.
UserSetControl ..................................................................................................................................................... 23
4.14.
Gamma ................................................................................................................................................................. 23
4.15.
CrossLine.............................................................................................................................................................. 24
4.16.
Binalize ................................................................................................................................................................. 24
4.17.
Aperture (Edge enhancement).............................................................................................................................. 24
4.18.
Black/White Inversion ........................................................................................................................................... 24
4.19.
Sensor Temperature Control ................................................................................................................................. 25
4.20.
AE&AGC Control .................................................................................................................................................. 25
5.
Camera connection / image confirmation method................................................................................................... 26
5.1.
Outline .................................................................................................................................................................. 26
5.2.
Recommended PC specs ..................................................................................................................................... 26
5.3.
Camera connection............................................................................................................................................... 27
6.
Other....................................................................................................................................................................... 31
6.1.
How to create gamma table .................................................................................................................................. 31
6.2.
How to load Gamma Table.................................................................................................................................... 32
6.3.
Packet Delay Settings........................................................................................................................................... 33
6.4.
Defect pixel correction setting ............................................................................................................................... 34
6.5.
PC settings............................................................................................................................................................ 36
6.6.
If you thought it was a malfunction (abnormal phenomenon check sheet)............................................................ 37
7.
Specification ........................................................................................................................................................... 39
7.1.
Image.................................................................................................................................................................... 39
7.2.
Optical, etc. ........................................................................................................................................................... 39
6
PRIMETECH ENGINEERING
6/43
7.3.
Spectral sensitivity characteristics ........................................................................................................................ 40
8.
External dimensions ............................................................................................................................................... 41
9.
Quality Assurance................................................................................................................................................... 42
9.1.
Quality Assurance Period...................................................................................................................................... 42
9.2.
Warranty coverage................................................................................................................................................ 42
9.3.
Repair procedure .................................................................................................................................................. 42
9.4.
Repairs after the free warranty period has expired ............................................................................................... 42
9.5.
Other..................................................................................................................................................................... 42
7
PRIMETECH ENGINEERING
7/43
1. Overview
This operation manual describes functions and procedures for the GigE Vision interface SWIR1.3M/0.3M (B/W) CMOS
Camera (B/W).
1.1. Characteristics
•Interface
Compliant with the GigE Vision interface. Supports DC12V input using the attached AC adapter.
•Resolution
The number of effective pixels of the camera module is 1280(H) x 1024(V) for PXG130SP/PXG130S,
640(H) x 512(V) for PXG030SP/PXG030S.
•Diverse mode setting
The following modes can be set by sending commands from the host device.
・Image acquisition mode (Continuous / Multi Frame)
・Shutter function: Normal/triggered shutter
・Output bit length switching
・Read mode: Normal / Vertical decimation / Horizontal decimation / Image cropping (ROI)
・Frame rate control
・Exposure Time control
・Gain control
・Black level control
・Gamma correction
・User set control
・Image reverse function (H/V)
・Binarization function
・Cross line display
・Test pattern display
・Sensor temperature display / control function (Temperature control is PXG130SP / PXG030SP only)
・Defect pixel correction
・Edge enhancement
・Black and white inversion
8
PRIMETECH ENGINEERING
8/43
・Triggered shutter
By using the external trigger, one still image can be obtained. Accurately capture objects moving at high speed.
・Output bit length switching
8 bit (MONO8) / 10 bit (MONO10) /12 bit (MONO12) output can be selected.
・Decimation function
The decimation of 1/2 horizontal and 1/2 vertical can be selected.
・Image cropping function (ROI)
Image cropping is possible in one area, 8 pixel steps (H/V).
・Frame rate
The frame rate can be set arbitrarily.
・Electronic shutter
The exposure time can be set arbitrarily.
・Gain
The analog gain can be set arbitrarily.
・Black level
The black level can be set arbitrarily.
・Gamma Correction
OFF (γ=1.0) / ON (the γcan be arbitrarily set by the user) can be switched.
・User set control
Camera settings can be saved and recalled.
・Image reverse
The image can be flipped horizontally and vertically.
・Binarization
The binarized image can be get. The threshold is arbitrary.
・Camera module fixing
The screw holes for fixing the camera module are located on the lower surface. Fixing the camera module on the front
panel can minimize deviation of the optical axis.
9
PRIMETECH ENGINEERING
9/43
2. System Configuration
The included contents, the items to be prepared by the customer, and an example of the system configuration are shown
below.
2.1. Included contents
< Camera module x 1> < Camera cable x 1 > < Dedicated AC adapter x 1>
< Spare connector x 1 > < CD-ROM x 1 >
2.2. Items to be prepared by the customer
< C-mount lens > < LAN cable ※1 > < The Data reception and image display devices such as PCs >
※1 LAN cable：
Use a LAN cable that supports 1000BASE-T (CAT5e or higher standard).
Use a LAN cable with excellent noise resistance. Depending on the characteristics of the LAN cable, the image may be
distorted or the camera module may become unstable.
10
PRIMETECH ENGINEERING
10/43
2.3. Items to be prepared by the customer as needed
< Network card ※2 >
※2 Network card：
Insert the network card into the expansion slot of the host device (PC, etc.). Use a 1000BASE-T compatible, jumbo packet
compatible one suitable for your system.
The LAN connector that comes with your PC is also can be used. In this case, a network card does not needed.
2.4. System configuration example
An example of the system configuration is shown below.
Camera module
C-mount lens
LAN cable
Dedicated
AC adapter
Camera cable
PC
AC100
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Primetech Wasserpumpe Handbücher
Beliebte Wasserpumpe Handbücher anderer Marken
Sykes AmeriPumps
Sykes AmeriPumps GP100M Fehlerbehebungshandbuch
DUROMAX
DUROMAX XP WX Series Bedienungsanleitung
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Bedienungsanleitung
Franklin Electric
Franklin Electric IPS Bedienungsanleitung
Xylem
Xylem e-1532 Series Bedienungsanleitung
Milton Roy
Milton Roy PRIMEROYAL Bedienungsanleitung