Pro-Elec PEL01926 Bedienungsanleitung
16" Wall Mount Fan with Remote Control
Model: PEL01926
IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before use and retain for future reference.
• When using electrical appliances basic safety precautions should always be
followed.
• Check that the voltage indicated on the rating plate corresponds with that of the
local network before connecting the appliance to the mains power supply.
• This appliance is intended for domestic use only. It should not be used for
commercial purposes.
• This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning the use of
the appliance in a safe way and understands the hazards involved.
• Children shall not play with this appliance.
• Cleaning and maintenance shall not be made by children without supervision.
• There are no user-serviceable parts in this product. Refer servicing to qualied
personnel.
• Do not operate this fan with a damaged plug or cord, after a malfunction or after
being dropped or damaged in any way.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a hazard.
• Ensure that the fan is switched off before removing the guard.
• Do not insert anything through the grille when the fan is in use.
• Make sure that the fan is stable when operating.
• It is recommended to unplug the fan from the mains socket when not in use.
FAN ASSEMBLY INSTRUCTIONS
INSTALLATION
Step one
Assemble the rear grille onto motor housing. Rear grille should
t onto the pins on the fan motor housing with the wire handle to
the top as shown:
Step two
Thread the locknut onto the motor housing
to lock the rear grille in place:
Step three
Remove any protective covering over the shaft
before fan blade installation.
Place the fan blade onto the motor shaft. Notice the
pin on motor shaft should engage into slots on the
fan blade hub:
• Offer the bracket up to the wall in the area of the room that will give
adequate fan cooling and mark the position of the three mounting
holes.
• Ensure the wall can support the weight of the fan and that there are
no concealed pipes or wires in the location to be drilled.
• Drill the wall and if required t appropriate wall plugs.
• Secure the bracket to the wall using suitable screws.
NOTE: It is recommended to hang the main unit to the wall bracket before
nal assembly of the fan as it allows easier access and the ability to
visually line up the lock screw to the threaded hole in the bracket.
• Hang the fan unit onto the bracket.
• Make sure it's fully located then screw home
the knurled head lock screw and tighten by
hand only.
OPERATION
Step four
Thread the blade cap onto threaded end of the
motor shaft. Note: threads are reversed.
ie: tighten counter-clockwise:
Step ve
Offer up the front grille to the rear grille with the
hook clip centred on the top above wire handle:
Step six
Press the remaining grille clips onto rear
grille to securely attach front grille.
Using the nut and bolt provided, lock the
two guard halves together.
Note: do not operate fan without the grille in place:
• Always operate the fan in the upright position following all instructions and
recommendations listed in this manual.
• Plug the fan into a suitable 13A mains socket. Check the plug is a good t in the
socket as a loose connection may cause overheating and damage to the plug,
socket or fan.
Note: Avoid using extension leads particularly if they are already supplying power to
any high consumption equipment.
• To start the fan, press SPEED/ON button. Press SPEED/ON repeatedly to
desired fan speed (LOW, MID, HIGH).
• Press OFF button to turn the fan off.
• Disconnect from the mains when not in use.
• To start fan oscillation, press SWING button on the control panel or remote control
while fan is operating at any speed or mode.
• To discontinue oscillation, press the SWING button again on the control panel or
remote control.
• The timer feature is accessed using the remote control, and is designed to work
during any fan mode or speed including oscillation.
• Press the TIMER button, each time it is pressed the time is increased in 0.5 hour
increments to a maximum timer setting of 7.5 hours.
• To turn the timer function off, press the TIME button continuously until all the timer
indicator lights are off.
• To adjust the tilt angle simply tilt the fan to desired position. The fan will remain at
the desired angle.
CLEANING & STORAGE
• Before cleaning, turn the fan off and unplug from the power supply.
• Use a soft cloth to wipe off any dust. If the fan is very dirty, use a damp cloth and
wipe dry.
• Do not use any chemicals, abrasives or solvents that could damage the fan.
TECHNICAL SPECIFICATION
Power consumption 45W
Main voltage 220-240V~ 50Hz
Dimensions (HxWxD) 540 x 430 x 300mm
Weight 2.5kg
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical
& Electronic Equipment (WEEE). Any WEEE marked products must not be mixed with
general household waste, but kept separate for the treatment, recovery and recycling of the
materials used. Contact your local authority for details of recycling schemes in your area.
Made in China. PR2 9PP
Man Rev 1.1
• The remote control has a range of about 8 metres.
• Accessed using the Remote Control, this fan has three operating modes that will
work with oscillation control ON or OFF.
• Normal - Fan speed is consistent with the speed chosen and operates like a
standard fan.
• Natural - Fan will vary the speed from the highest fan speed chosen to very slow
speed.
• Sleep - Fan will vary the fan speed like natural mode but it is timed to slow down
after a period of time. The speed will change as follows:
1. When fan speed is set to HIGH, the fan will run varying from HIGH speed to very
slow speed for 30 minutes, then run from MEDIUM to very slow speed for 30
minutes, then run from LOW speed to very slow speed for the duration of use
2. When fan speed is set to Medium, the fan will run varying from MEDIUM speed to
very slow speed for 30 minutes, then run from LOW speed to very slow speed for
the duration of use.
3. When fan speed is set to LOW, the fan will vary from LOW speed to very low
speed for the duration of use.
FAN MODES
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Pro-Elec Lüfter Handbücher
Pro-Elec
Pro-Elec FT-15 Bedienungsanleitung
Pro-Elec
Pro-Elec HG00875 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL00303 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL00301 Bedienungsanleitung
Pro-Elec
Pro-Elec FD-40M Bedienungsanleitung
Pro-Elec
Pro-Elec TF-35 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01937 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01916 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01927 Bedienungsanleitung
Pro-Elec
Pro-Elec FT-40MC Bedienungsanleitung
Pro-Elec
Pro-Elec TF-29GR Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01924 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL00294 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01936 Bedienungsanleitung
Pro-Elec
Pro-Elec TF-29N Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01935 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01930 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL00305 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01915 Bedienungsanleitung
Pro-Elec
Pro-Elec PEL01918 Bedienungsanleitung
