Pro-Ject Audio Systems Pro-Ject MaiA Bedienungsanleitung

INSTRUCTIONS FOR USE

Pro-Ject MaiA

Pro-Ject MaiA Pre

Dear music lover,

thank you for purchasing a Pro-Ject Audio Systems´ amplifier.

In order to achieve maximum performance and reliability you should study these instructions for use carefully.

Warning of a hazard for the user, the unit or possible misuse.

Important notice.

Safety instructions

AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the

voltage in your area meets the voltage requirements printed on the power supply.

The power supply is used to connect/disconnect the unit from the mains. Make sure that the power

supply is easily accessible at all times. Never handle the device, the power supply while your hands are

wet or damp. Avoid letting liquids enter the device or the power supply. Never place any item

containing liquid, such as a flower vase on or near the device. Never spill any liquid on the device or

the power supply. Never place any naked flame sources, such as lighted candles on or near the device.

The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any

other similar conditions.

Connectors

MaiA

MaiA Pre

1. Make all connections except the connection to the headphone and USB whilst the unit is

disconnected from the mains.

2.Never connect or disconnect power supply to or from the unit whilst the power supply is connected to

the mains !Never use any other power supply than the one supplied with the unit with the exception of

dedicated Power Boxes which can replace original power supplies.

3. Take care to connect the left and right channels of In1, In2, In3 correctly. The right channel is usually

marked red, the left channel black or white.

4. Maia only: Speaker connections for the left speaker are located on the right hand side of rear view

above, connections to right speaker are located near the power socket. Speaker connectors marked red

represent +according indicators on speaker terminal.

Line output

A power amplifier or active loudspeakers can be connected to the output sockets marked Output.

Connection to the speakers (Maia only)

The output terminals accept loudspeaker cables terminated with 4mm Banana plugs, spades connectors

or naked wire.

Phono input

Connect the tonearm signal lead to the In 1 Phono of the amplifier. The earthing wire may be connected to

the screw terminal if you encounter hum problems when using the turntable.

Line inputs

Line level sources such as CD player, radio or TV can be connected to the input sockets marked In 2,In3 or

In 4.

Digital inputs

Sources with a digital output such as TV satellite/cable receiver or a game console can be connected to the

digital inputs. Coaxial to In 5 and optical to In 6 and In 7.

Connecting to a Computer

Connect the USB-input In 8 USB of the MaiA (unit must be switched on) to a free USB-socket on your

computer and turn it on/make sure it is powered on. Select input 8USB.

* For Windows®operating systems an USB Class 2 driver (supplied on CD) has to be installed. For MaiA with

Windows® version 1.61.2 or higher is needed.

Mac OS®operating systems do not need an additional driver or setup.

Linux operating systems include an USB Audio Class 2 driver from Linux Kernel 2.6.35 and higher.

Please note: Connection should be made to an USB-socket of your computer directly. Connecting to

USB-hubs or switches can cause problems.

24Bit/192kHz playback with Windows® operating systems

* For Windows®operating systems a 24Bit/192kHzUSB driver (supplied on CD) has to be installed. Insert the

included CD into the drive of you PC and follow the instructions.

After installing the driver, some settings have to be checked/done.

For example - Windows 7®operating system:

Control Panel Hardware and Sound SoundPlayback:

select Speaker/MaiA USB 2.0 Audio Out

Properties Supported formats: make sure nothing is assigned

Level Sound: setting must be 100

Enhancements: disable all enhancements Advanced Default Format: set to studio quality 24/192

Mains power connection

Connect the low voltage plug from the power supply to the Power socket before connecting the power supply

to the mains.

Remote control

turns the unit on or back into standby (long press), mute (short)

and adjust the sound volume

and select the inputs

VOL+ and CH+ confirm Bluetooth pairing

VOL- and CH- cancel Bluetooth pairing

Front panel controls

To switch on from standby or to standby

The push button on the left side of the front panel turns the unit on or back into standby. The blue LED above

the stand-by push button shows that the unit is switched on. Mute is active when LED is blinking.

Input selector

After the unit is powered on, pressing the buttons◄ and ►next to the LEDs inputs indicators selects

desired input.

Volume

Adjust the volume to the desired level, using the large knob on the front panel.

Connecting a headphone

Connect the headphones to the ¼“ (6,3mm ) jack socket on the front of the unit.

Bluetooth connection

Make sure the antenna is attached to its connector In 9 BT on the back panel prior using Bluetooth.

Bluetooth is active only once input 9 is selected. LED of Bluetooth input is blinking when no device is

connected. If the LED is on, active connection with Bluetooth device is established. Following procedures

refer to units from S/N E29069 and higher including previous units with implemented firmware update v1.3.

If you need a manual for units with previous serial numbers without firmware update, please contact your

local distributor.

Pairing with Android devices

Open Settings and tap on Bluetooth. Turn on Bluetooth and tap on Scan. Searched devices will show up.

Tap on "MaiA" and confirm presented pairing code on your Android device. Then press ►(pair) button on

MaiA (alternatively CH+ or VOL+ button on remote control) when the blue LED of input 9 starts blinking.

When paired with MaiA, your Android device will show "Connected to media Audio". Now you can play

music from your Android device over Bluetooth to MaiA.

CH+

CH-

VOL+

VOL-

ON/OFF

VOL

Older devices may request a pairing code. Enter "0000" and confirm. No more confirmation on MaiA

is then needed.

Bluetooth pairing with Apple devices

Tap on Settings, tap on Bluetooth, turn on Bluetooth. Your device will automatically start searching for

available devices. Tap on "MaiA" and confirm by pressing ► (pair) button on MaiA(alternatively CH+ or

VOL+ button on remote control) when the blue LED of input 9 is blinking.

Bluetooth pairing with Windows smartphones

Open Settings and tap on Bluetooth. Turn on Bluetooth and a scan for available devices starts automatically.

Searched devices will show up. Tap on "MaiA" and confirm presented pairing code on your Windows device.

Then press►(pair) button on MaiA (alternatively CH+ or VOL+ button on remote control) when the blue

LED of input 9 starts blinking. When paired with MaiA, your Windows device will show "Connected to media

Audio". Now you can play music from your Windows device over Bluetooth to MaiA.

Bluetooth pairing with Windows PC

For example - Windows 7®operating system:

Control Panel Devices and PrintersAdd device

Select MaiA(make sure no other Bluetooth device is connected)Confirm by pressing ► (pair) button

on MaiA (alternatively CH+ or VOL+ button on remote control) when the blue LED of input 9 is blinking

PC screen will display this question: “Confirm if code is identical”

Select “Yes” and continue

Select MaiA from list of devices with double-click

Select “Listen to music” and make sure that “Bluetooth Audio” is selected as standard device

MaiA can store up to 8 Bluetooth devices. If the memory is full, new connections will automatically

replace the oldest connections. A new connection is only possible if the LED of BT input is blinking

slowly (it indicates that no device is connected).If a problem with Bluetooth connection occurs, it is

necessary to reset memory and to delete all paired devices. For reset turn off the unit > disconnect

power supply > press & hold power button > connect power supply > hold power button for 5

seconds > release power button. The blue LED above the power button will blink for few seconds.

When the LED stops blinking, memory is erased and you can turn on the unit.

Replacing batteries

Proceed as follows:

Unlock and slide open the battery case cover

Replace the battery.

Make sure the battery is the right way round !

Close the battery case cover

Battery type: 1 x CR2032 / 3V or 1 x CR2025 / 3V

Do not dispose the batteries as ordinary domestic refuse. Please dispose your exhausted batteries at

the appropriate collection sites - usually located at supermarkets and drugstores.

Technical specifications Pro-Ject MaiA

Power output : 2x 25W/37W at 8 ohms/4 ohms (both channels driven)

Frequency response : 20Hz - 20kHz (-0,3dB, -2,5dB)

Channel separation : > 65dB at 20kHz

Noise floor : > -90dB (A weighted)

THD : < 0,07% at 15W

Gain : 31dB (measured via line level input)

Line level inputs : 2 pair RCA + 1 jack 3.5mm

Line input sensitivity : 350mV

Line input impedance : 50kohms

Phono input : 1 pair RCA

Phono input sensitivity : suitable for MM, MI or high output MC cartridges

Phono input impedance : 47kohms

Phono input gain : 40dB

S/PDIF coaxial input : up to 24bit and 192kHz

S/PDIF optical input : up to 24bit and 96kHz

USB input : USB Audio Class 2 requires USB 2.0 or higher on computer

USB data transfer : Asynchronous

Digital to Analogue converter : Cirrus Logic CS4344 24bit/192kHz Multi-bit Delta Sigma type

Variable line level output : jack 3.5mm

Bluetooth version: 2.1 +EDR

Bluetooth music receiver codec : aptX, A2DP profile

Bluetooth range : 10 meters in direct visibility between source and receiver

Speakers connectors: 4mm banana plugs, spades connectors or naked wire

Headphone output : 6,3mm jack (16 –600ohms)

Outboard power supply : 20V/3A DC, suitable for your country's mains supply

Power consumption : max. 3A DC, <0.5W in standby

Replacement battery remote control : 1 x CR2032 / 3V or 1 x CR2025 / 3V

Dimensions W x H x D (D with sockets) : 206 x 36 x 150 (165)mm

Weight : 1250 g without power supply

Technical specifications Pro-Ject MaiA Pre

Variable line level output : 1 pair RCA

Headphone output : 6,3mm jack (16 –600ohms)

Output voltage : 2V RMS

Output impedance : 100 ohms

Frequency response : 20Hz - 20kHz (max. deviation 0,3dB)

Noise floor : > -95dB (A-weighted)

THD : < 0,01%

Gain : 6 dB (measured via line level input)

Line level inputs : 2 pair RCA + 1 3.5mm jack

Line input sensitivity : 350mV

Line input impedance : 50kohms

Phono input : 1 pair RCA

Phono input sensitivity : suitable for MM, MI or high output MC cartridges

Phono input impedance : 47 kohms

Phono input gain : 46 dB

S/PDIF coaxial input : up to 24bit and 192kHz

S/PDIF optical input : up to 24bit and 96kHz

USB input : USB Audio Class 2 (requires USB 2.0 or higher on computer)

USB data transfer : Asynchronous

Digital to Analogue converter : Cirrus Logic CS4344 24bit/192kHz Multi-bit Delta Sigma type

Bluetooth music receiver codec : aptX, A2DP profile

Bluetooth range : 10 meters in direct visibility between source and receiver

Outboard power supply : 18V/1A DC, suitable for your country's mains supply

Power consumption : max. 250mA DC, <0.5W in standby

Replacement battery remote control : 1 x CR2032 / 3V or 1 x CR2025 / 3V

Dimensions W x H x D (D with sockets) : 206 x 36 x 150 (157) mm

Weight : 1100 g without power supply

Service

Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for

further advice. Only if the problem cannot be resolved there, the unit should be sent to the responsible

distributor in your country.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use. Modification or changes to any part of the product by unauthorized persons release the

manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pro-Ject Audio Systems Verstärker Handbücher

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box Design Pre Box DS Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box SE Mono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box SE Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems DS2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box SE Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box S2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box S Phono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems power box ds Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Head Box S Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Tube Box SE Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box SE II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box S Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems AMP BOX DS Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box MK II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box DS Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems DS2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box Mono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box-Design MaiA S3 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box SE II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box DS Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung