Pro-Ject Audio Systems T1 Phono SB Bedienungsanleitung

INSTRUCTIONS FOR USE

Pro-Ject T1 / T1 Phono SB

Dear Music Lover,

Congratulations and thank you for choosing Pro-Ject Audio Systems record player.

Your Essential III turntable has been handcrafted and rigorously tested by skilled technicians to give you

years of enjoyable, trouble free service.

Please contact your dealer if you require additional assistance.

Important:

Your turntable was shipped partially disassembled in order to avoid damage to sensitive parts.

Please

check immediately to make sure that neither the packaging nor the device was damaged in

transit. If you are

missing parts or if the unit is damaged, please do not operate and contact your

dealer.

Contents

Product illustrations 4

General setup

1. Platter and drive belt installation 5

2. Cartridge installation, stylus exchange 5

3. Vertical Tracking Force setting (VTF) 6

4. Maintenance and cleaning 7

5. Specific turntable informations

a) T1 7

b) T1 PHONO SB 8

Technical parameters 9

Troubleshooting, warranty, service 10

Exploded view of the packaging 11

Please do your part to help protect the environment:

Disposal of packaging material:

Pro-Ject packaging is carefully designed to protect your component from damage in transit

and you are

strongly urged to keep the original packaging in order to safely ship or

otherwise transport your turntable in

the future.

However, the packaging materials were chosen to be environmentally friendly, so if

you must discard the

packaging, please recycle.

GENERAL INFORMATIONS

Controls, features and connections

1 PLATTER & FELT MAT

2 CHASSIS

3 MOTOR WITH PULLEY

4 SUB –PLATTER

5 DRIVE BELT

6 TONEARM COUNTERWEIGHT

7 TONEARM LIFT LEVER

8 TONEARM REST / REMOVABLE TRANSPORT LOCK

9 TONEARM TUBE

10 HEADSHELL WITH FINGER LIFT AND PRE-MOUNTED ORTOFON CARTRIDGE

14 LID

13 LID HINGES

14 HINGE FASTENERS

15 POWER SUPPLY SOCKET

Accessories

2 SINGLE ADAPTOR

4 ALLEN KEY 1,5mm

5 COUNTERWEIGHT no. 56 (already mounted and pre-adjusted)

6 TWO-POINT CARTRIDGE ALIGNMENT PROTRACTOR

8 CONNECTION CABLE (CONNECT IT E RCA)

9 INSTRUCTION FOR USE

SETUP

1. Platter and drive belt installation

Please remove drive belt from accessories box and install it as shown in the following ilustration. Put the felt

mat on the top of the platter.

2. Cartridge installation, stylus exchange

* If you purchased this turntable in a package that included the cartridge, this has already been done for

you.

Install the cartridge into the aluminium headshell, using the appropriate hardware included with your

cartridge. All cartridges with half inch mounting holes can be fitted.

Connect the cartridge as indicated below:

•White left channel L+

•Red right channel R+

•Green right channel R-

•Blue left channel L-

For correct cartridge alignment, use the two-point cartridge alignment protractor provided with your T1

accessories. If unfamiliar with two-point setup, please refer to your dealer.

A damaged or worn stylus may harm your record collection and should be replaced.

Please remove stylus protection before pulling the stylus from the cartridge and replace for a new one.

Stylus type is exchange for pre-mounted cartridge Ortofon OM 5e: Stylus OM 5e. If in doubt, consult your local

dealer or distributor.

3. Vertical Tracking Force setting (VTF)

* This setting is only neccessary when you decided to repalce your cartridge. For factory fitted cartridge, VTF

was perfectly pre-set already.

Before setting the Vertical Tracking Force, confirm the exact weight of your cartridge.

Pushing carefully, move the counterweight onto the rear end of the counterweight support rod as shown in

the illustration below. Place the stylus pressure gauge onto the platter. To set the required VTF, lower the

tonearm lift lever as indicated in the illustration and place the tip of the stylus exactly in between the two

points marked 15mN and 20mN.

If the stylus gauge becomes level, then the correct pressure has been achieved. However if the there is

insufficient or excessive pressure the gauge will either not move or tilt down.

To adjust the amount of pressure, carefully move the counterweight (11) along the support rod, until the

stylus pressure is sufficient to raise the pressure gauge to the level position. Moving the counterweight (6)

away from the cartridge will reduce pressure and towards will increase pressure. Finally secure the

counterweight (6) using hexagonal key provided.

4. Maintenance and cleaning

Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic

cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic

cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber

parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.

If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.

T1 SPECIFIC

INFORMATIONS

Controls, features and connections

1 ON/OFF SWITCH

2 DOUBLE STEP PULLEY

3 OUTPUT CABLE CONNECT IT E

4 DIRECT POWER CORD

__________________________________________________________________________________________

Switching on and off

Pressing the ON/OFF switch alternately starts or stops the motor.

Changing replay speed

To play 45 r.p.m., put the drive belt over the larger diameter part of the motor pulley. To revert to 33 r.p.m.

repeat the proceedings using the smaller step on the pulley.

Connection to the amplifier

The record player has a captive tonearm signal lead for connection to the amplifier. Use the Phono input on your

amplifier. Make sure that the phono input offers correct matching and amplification for the type of cartridge used.

Line inputs (such as CD, Tuner, Tape or Video) are not suitable.

Take care to connect the left and right channels correctly. The right channel is usually marked red, the left

channel black or white. Check the manual supplied with your amplifier for relevant information. The earthing

wire of the tonearm lead should be connected to the earth terminal on your amplifier (if provided).

If your amplifier does not have an input suitable for phono cartridges you will require a separate phono

amplifier stage for MM or MC cartridges which is then connected between the record player and a free line

level input of the amplifier..

T1 Phono SB SPECIFIC

INFORMATIONS

Controls, features and connections

1 ON/OFF SWITCH

2 MOTOR PULLEY

3 SPEED SELECTOR

4 PHONO/LINE OUTPUT, EARTH CONNECTION

5 PHONO/LINE OUTPUT SWITCH

6 POWER SUPPLY SOCKET

__________________________________________________________________________________________

Switching on and off, changing replay speed

Pressing the ON/OFF switch starts the motor of the turntable. Pressing the speed selector selects between 33

r.p.m. and 45 r.p.m. The selected speed is shown respectively by the flashing LED. When the platter has

attained full speed, the LEDs stop flashing.

Connection to the amplifier

The record player has gold plated female RCA phono sockets and possibility to choose between Phono and LINE

output. With LINE OUT on, you can use a line input (such as AUX, CD, Tuner, Tape or Video) on your amplifier.

With PHONO OUT on, you can use your own phono pre-amplifier (sometimes labelled gram, disc or RIAA).

Take care to connect the left and right channels correctly. The right channel is usually marked red, the left

channel black or white. The earthing wire of the tonearm lead should be connected to the earth terminal on

your amplifier (if provided).

Technical specifications Pro-Ject T1 Phono SB / Pro-Ject 8.6

Nominal speeds

33/45 r.p.m.

Speed variance

33: ±0.70% 45: ±0.60%

Wow and flutter

33: ±0.25% 45: ±0.23%

Signal to noise

-65dB

Effective tonearm mass

8.0g

Effective tonearm length

8.6" (218,5mm)

Overhang

22,0mm

Power consumption

4,5W

Outboard power supply

15V/800mA DC, suitable for your country's mains supply

Dimensions (W x H x D)

420 x 112 x 330mm

Weight

5,0kg

Dimensions packaging (W x H x D)

488 x 235 x 393mm

Weight incl. packaging

7,0kg

Technical specifications MM-Cartridge Ortofon OM 5E

Frequency range

20-25.000Hz

Channel separation

22dB/1kHz

Output voltage

4mV

Recommended load impedance

47kohms/amplifier connection –MM-input

Compliance/stylus type

20µm/mN –elliptical

Recommended tracking force

17,5mN

Weight

Technical specifications MM phono pre-amplifier

Gain

34dB

Output voltage typically

200mV/1kHz at 5mV/1kHz input

Input impedance

47kohms/100pF

Noise floor

-68dB

RIAA-equalisation curve accuracy

20Hz-20kHz / max. 0,5dB

Potential incorrect use and fault conditions

Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before

leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but

can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common

fault symptoms is included.

The platter doesn't turn although the unit is switched on:

The unit is not connected to the mains power supply.

No mains at the socket.

Drive belt is not fitted or has slipped off.

No signal through one or other channel or both channels:

No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or

from that to the phono box or between that and the amplifier. This could be due to a faulty plug,

broken wire or solder joint or simply loose plug/socket connection.

Phono input not selected at amplifier.

Amplifier is not switched on.

Amplifier or speakers are defective or muted.

No connection to the loudspeakers.

Strong hum on phono input:

No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.

Distorted or inconsistent sound from one or both channels:

Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.

Needle or cantilever damaged.

Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged

Service

Should you encounter a problem which you are not able to alleviate or identify despite the above information,

please contact your dealer for further advice. Only when the problem cannot be resolved there should the

unit be sent to the responsible distributor in your country.

Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend

keeping the original packaging.

Never return a record player without making sure that is it safely disassembled and correctly packaged in the

original packaging according to the diagrams on the last page of this user guide. Please remove these parts

and pack them separately: lid, counterweight, anti-skating weight and belt.

Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the

record player.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use and/or by transportation without the original packaging. Modification or change to any part

of the product by unauthorized persons, release the manufacturer from any liability over and above

the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to press.

The manufacturer reserves the right to make changes to

the technical specification without prior notice as deemed

necessary to uphold the ongoing process of technical

development.

Andere Handbücher für T1 Phono SB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pro-Ject Audio Systems Drehscheibe Handbücher

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon RecordMaster HiRes Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential / Phono USB Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon EVO Betriebsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems VT-E BT L Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems T2 W Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems ESSENTIAL III Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 9 Carbon Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 6.1 SB SuperPack Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject VC-S Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject 1 Xpression III Comfort Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Signature 12 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 9.1 SuperPack 1 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Juke Box E1 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut RecordMaster II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 6.1 SB SuperPack Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Align it DS3 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems T1 Phono SB Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems SIGNATURE 10 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut S Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems VC-S Firmware-Update

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 5.1 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon Phono/USB Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems 6 PerspeX Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung