Pro-Lift F-2332A Gebrauchsanweisung

Hydraulic

Floor Jack

Operating Instructions & Parts Manual

Model Number

F-2332A

F-2392A

F-388P

Capacity

2 Ton

Ton

Manufactured by

MVP (H.K.) Industries Ltd.

Unit 1101 Lippo Sun Plaza,

28 Canton Road, Tsimshatsui,

Kowloon, Hong Kong Printed in China

F-2392A-M0 issue 09/07

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

Save these instructions. For your safety, read, understand, and follow the information

provided with and on this jack before using. The owner and/or operator of this jack shall

have an understanding of the jack and safe operating procedures before attempting to

use. The owner and/or operator shall be aware that the use and repair of this product

may require special skills and knowledge. Instructions and safety information shall

be conveyed in the operator’s native language before use of this jack is authorized.

If any doubt exists as to the safe and proper use of this jack, remove from service

immediately.

Inspect before each use. Do not use if broken, bent, cracked, or damaged parts

(including labels) are noted. Any jack that appears damaged in any way, operates

abnormally or is missing parts, shall be removed from service immediately. If you

suspect that the jack was subjected to a shock load (a load dropped suddenly,

unexpectedly upon it), immediately discontinue use until the jack has been checked

by a factory authorized service center (contact distributor or manufacturer for list of

Authorized Service Centers). It is recommended that an annual inspection be done

by qualiﬁed personnel. Labels and owner’s manuals are available from manufacturer

(see page 7).

SAFETY AND GENERAL INFORMATION

PRODUCT DESCRIPTION

Hydraulic Floor Jack is designed to lift, but not support, one end of a vehicle. This Jack

must be used in conjunction with a pair of appropriately rated jack stands.

NEVER use a hydraulic jack as a stand-alone device. After lifting, immediately

support the lifted vehicle with a pair of appropriately rated jack stands.

Figure 2 - Typical Floor Jack Nomenclature

PACKAGE CONTENTS

Part Description Quantity

A Jack 1

B Pumping Handle 1

C Carrying Handle 1

Figure 1 - Package Contents

Handle

Release Valve

Cover Plate

(remove to access

oil ﬁller plug)

Engage release

valve w/this end

Front Wheel

Saddle

Handle Grip

Rear Caster

Handle Sleeve

Oil Filler Plug

(not shown, on

reservoir)

Lifting Arm

Carrying

Handle

•

Study, understand, and follow all instructions

provided with and on this device

before use.

• Do not exceed rated capacity.

• Use only on hard, level surface.

• This is a lifting device only!

• Immediately after lifting, support the vehicle with a pair of appropriately rated

jack stands.

• Never work on, under, or around a load supported only by this device.

• Do not move or dolly the vehicle while on the jack.

• No alterations shall be made to this device.

• Lift only on areas of the vehicle as speciﬁed by the vehicle manufacturer.

• Failure to heed these markings may result in personal injury and/or property

damage.

! WARNING

To avoid crushing and related injuries:

• Never work on, under, or around a load supported only by a hydraulic jack.

• Read, understand and follow all printed materials provided with and on this

jack.

• Immediately support the lifted vehicle with a pair of appropriately rated jack

stands.

• Use ONLY on vehicles whose lift points are compatible with the saddle of this

jack. Incompatibility may result in structural damage to the vehicle and/or jack.

• Chock each unlifted tire in both directions.

• Be alert and sober when using this product! Never operate this equipment

when under the inﬂuence of drugs or alcohol.

• DO NOT use this device to lift, level, lower, support, adjust or otherwise move

a house, mobile home, travel trailer, camper, or building structure of any type,

size, or conﬁguration.

! WARNING

PREPARATION

Before Use

Verify that the product and the application are compatible, if any doubt call Customer

Support @ (816) 891-6390.

2. Before using this product, read the owner’s manual completely and familiarize

yourself thoroughly with the product, its components and recognize the hazards

associated with its use.

3. To familiarize yourself with basic operation, use the stamped end of the provided

handle to engage and turn the release valve:

Clockwise until ﬁrm resistance is felt

to further thread engagement. This is the

‘CLOSED’ release valve position used to raise the load.

Counter-clockwise, but no more than 1/2 full turn from the closed position.

This is the

‘OPEN’ release valve position used to lower the load.

4. With saddle fully lowered, locate and remove the cover plate, then remove the oil

ﬁller plug. Insert the handle into the handle sleeve; then pump 6 to 8 full strokes.

This will help release any pressurized air which may be trapped within the reservoir.

Check oil level. Proper oil level will vary from just covering the ram cylinder to 3/16”

above it as seen from the oil ﬁller plug hole. Reinstall the oil ﬁller plug.

5. Check to ensure that jack rolls freely (if so equipped) and that the pump operates

smoothly before putting into service. Replace worn or damaged parts and assemblies

with factory Authorized Replacement Parts only. Contact the manufacturer or

distributor of this product for a list of factory authorized service centers (see page 7,

Replacement Parts List). Lubricate as instructed in Maintenance Section.

Bleeding / Venting Trapped Air

With the release valve in the OPEN position (3b above) and with saddle fully lowered,

locate and remove the oil ﬁller plug. Insert the handle into the handle sleeve; then

pump 6 to 8 full strokes. This will help release any pressurized air which may be

trapped within the reservoir. Oil level should be even with the bottom of the oil ﬁller

plug hole. Reinstall the oil ﬁller plug.

OPERATING INSTRUCTIONS

This is the safety alert symbol.

It is used to alert you to potential personal

injury hazards. Obey all safety messages that follow this symbol to avoid

possible injury or death.

Lifting

1. Place vehicle in park, with emergency brake on and wheels securely chocked to

prevent inadvertent vehicle movement.

Locate and close release valve by turning handle clockwise until ﬁrm resistance is felt

to further thread engagement. Center jack saddle under lift point.

3. Insert handle into handle sleeve and pump to contact lift point. Verify the lift point,

then pump the handle until load reaches desired height.

4. Transfer the load immediately to a pair of appropriately rated jack stands.

Use only the handle assembly provided by the jack manufacturer. The

handle

assembly provided with this jack will safely engage the release valve

and operate the handle sleeve. If the handle is worn, operates abnormally, or will

not positively engage the release valve, STOP, discontinue use of the jack until a

factory replacement handle assembly can be acquired.

Lowering

1. Raise load high enough to clear the jack stands; then carefully remove jack stands

(always used in pairs).

2. Slowly turn the handle counter-clockwise, but no more than 1/2 full turn. If the load

fails to lower:

a. Use another jack to raise the vehicle high enough to reinstall jack stands.

b. Remove the affected jack and then the stands.

c. Using the other jack, lower the load by turning the operating handle

counter-clockwise, but no more than 1/2 full turn.

After removing jack from under the load, push saddle down to reduce ram exposure

to rust and contamination.

CARE AND MAINTENANCE

Maintenance

Important: Use only a good grade

hydraulic jack oil. NEVER use brake ﬂuid,

turbine oil, transmission ﬂuid, motor oil or

glycerin. Improper ﬂuid can cause failure

of the jack and the potential for sudden and

immediate loss of load. We recommend

Mobil DTE13M or equivalent.

Adding oil

1. With saddle fully lowered set jack in

its upright, level position. Locate and

remove oil ﬁller plug.

2. Proper oil level will vary from just

covering the inner cylinder to ~3/16”

above the inner cylinder as seen from

the oil ﬁller plug hole. If the oil level

is too low, the jack will not raise to its

advertised maximum height. Reinstall

the oil ﬁller plug.

NOTICE: DO NOT overﬁll the reservoir.

An overﬁlled reservoir can cause a wide

variety of performance problems and

create an oily mess on the shop ﬂoor!

See the troubleshooting guide, page 6.

Changing oil

For best performance and longest life,

replace the complete ﬂuid supply at least

once per year.

1. With saddle fully lowered, remove the

oil ﬁller plug.

2. Lay the jack on its side and drain the

ﬂuid into a suitable container.

Note: Dispose of hydraulic ﬂuid in

accordance with local regulations.

3. Fill with oil. Proper oil level will vary

from just covering the inner cylinder

to ~3/16” above the inner cylinder

as seen from the oil ﬁller plug hole.

Reinstall the oil ﬁller plug.

Lubrication

A periodic coating of light lubricating oil

to pivot points, axles and hinges will help

to prevent rust and assure that wheels,

casters and pump assemblies move

freely.

Cleaning

Periodically check the pump piston and

ram for signs of rust or corrosion. Clean

as needed and wipe with an oily cloth.

Note: Never use sandpaper or abrasive

material on these surfaces!

Storage

Store the jack with the pump piston, ram

plunger, and saddle fully lowered and the

release valve open, but never more than

1/2 turn. This will help prevent rust and

corrosion to those critical surfaces.

OPERATING INSTRUCTIONS (continued)

TROUBLESHOOTING

Symptom Possible Causes Corrective Action

Jack will not lift load • Release valve not

tightly closed.

• Load is too heavy.

•

Ensure release valve tightly

closed. Use the provided handle

to engage the release valve.

Turn the release valve clockwise

until ﬁrm resistance is felt.

•

Consider higher capacity jack.

Jack *bleeds off after lift

* ‘bleeds off’ means

the load slowly and

unintentionally lowers

after lifting

•

Hydraulic unit

malfunction.

• Discontinue use, contact

Customer Support.

While lowering, ﬂuid

leaks from reservoir

area.

Jack saddle will not

descend to lowest

advertised height

• Reservoir overﬁlled.

• Ram plunger/cylinder

deformed, seized up

in ram cylinder and/

or top nut, likely the

result of off-center

• Drain ﬂuid to proper level.

• Contact Customer Support.

Ram plunger will not

remain lowered after

released from contact

with load (creeps back

up)

• Air trapped in

system.

• IF there is no longer contact

between the lifted load and

the jack saddle, simply

remove the jack and follow

the instructions on page 4

for bleeding air from system.

However, IF there is any

loaded contact between

the saddle and the vehicle,

STOP, use another jack to

raise the load high enough to

re-install jack stands. Remove

the affected jack, then the

stands. Using the other jack,

lower the load by turning

the release valve counter-

clockwise, but never more

than 1/2 full turn, then follow

the instructions on page 4 for

bleeding air from system.

Poor lift performance • Fluid level low.

• Air trapped in

system.

•

Hydraulic unit

malfunction.

• Ensure proper ﬂuid level.

• With ram fully retracted, follow

the instructions for bleeding

air on page 4.

• Contact Customer Support.

Will not lift to full

extension

• Fluid level low. • Ensure proper ﬂuid level.

REPLACEMENT PARTS

Not all components of the jack are replacement items, but are illustrated as a convenient

reference of location and position in the assembly sequence. When ordering parts,

give model number, serial number and description below. Call or write for current

pricing: Customer Support, 10939 N. Pomona Ave., Kansas City, MO 64153.

Phone (816) 891-6390, Fax (816) 891-6599

Model F-2332A, F-2392A & F-388P

Item Description Quantity

1 Power Unit 1

2 Front Wheel Assembly 2

3 Rear Caster Assembly 2

4 Saddle 1

5 Oil Filler Plug 1

6 Return Spring 1

7 Handle 1

8 Spring Clips 5

-- Labels 2

-- Owner’s Manual 1

Figure 3 - Replacement Parts Illustration

2 YEARS LIMITED WARRANTY

For a period of 2 years from the date of purchase, MVP (H.K.) Industries Ltd. will repair

or replace, without charge, any of its products which fails due to a defect in material or

workmanship. Performance of any obligation under this warranty may be obtained by

simply returning the product during the warranty period to your retailer with the original

receipt along with an explanation of the defect. This warranty does not cover damage or

failure resulting from misuse, abuse or modiﬁcation of the product. MVP MAKES NO

OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT

LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. IN ADDITION, THIS WARRANTY DOES NOT COVER

INCIDENTAL OR CONSEQUENTIAL DAMAGES SUCH AS PHYSICAL INJURIES

OR PROPERTY DAMAGE, LOSS OF TIME, LOSS OF USE OF VEHICLE, ETC. This

warranty gives you speciﬁc legal rights, and you may also have other rights which

vary from state to state. Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you. Some states do not allow

the exclusion or limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you.

WARRANTY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pro-Lift Jack Handbücher

Pro-Lift

Pro-Lift PL1002 Bedienungsanleitung

Pro-Lift

Pro-Lift T-9400 Gebrauchsanweisung

Pro-Lift

Pro-Lift F1500A Bedienungsanleitung

Pro-Lift

Pro-Lift Garage in a Box Gebrauchsanweisung

Pro-Lift

Pro-Lift B-002D Gebrauchsanweisung

Pro-Lift

Pro-Lift F1400 Bedienungsanleitung

Pro-Lift

Pro-Lift G-4630 Gebrauchsanweisung

Pro-Lift

Pro-Lift T-6902D Gebrauchsanweisung

Pro-Lift

Pro-Lift G-4630JSC Gebrauchsanweisung

Pro-Lift

Pro-Lift B-002NC Gebrauchsanweisung

Pro-Lift

Pro-Lift G2000SA Bedienungsanleitung

Pro-Lift

Pro-Lift F-2330BMC Gebrauchsanweisung

Pro-Lift

Pro-Lift F1350 Bedienungsanleitung

Pro-Lift

Pro-Lift F-2332 Gebrauchsanweisung

Pro-Lift

Pro-Lift F1800 Bedienungsanleitung

Pro-Lift

Pro-Lift F1800A Bedienungsanleitung

Pro-Lift

Pro-Lift SG-5625 Gebrauchsanweisung

Pro-Lift

Pro-Lift F1650 Bedienungsanleitung

Pro-Lift

Pro-Lift G2000 Bedienungsanleitung

Pro-Lift

Pro-Lift B-1850 Bedienungsanleitung

Pro-Lift

Pro-Lift PL3200 Gebrauchsanweisung

Pro-Lift

Pro-Lift PRO-A1200 Bedienungsanleitung

Pro-Lift

Pro-Lift F-2525 Gebrauchsanweisung

Pro-Lift

Pro-Lift F2000A Bedienungsanleitung

Beliebte Jack Handbücher anderer Marken

Omega Lift Equipment

Omega Lift Equipment 18122C Gebrauchsanweisung

Pittsburgh

Pittsburgh 58816 Montageanleitung

Unimec

Unimec TP Bedienungsanleitung

Sonic

Sonic 4800703 Bedienungsanleitung

BGS technic

BGS technic 70039 Bedienungsanleitung

TradeQuip

TradeQuip 1128T Bedienungsanleitung

VEVOR

VEVOR TJD-12000SP-F Bedienungsanleitung

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Bedienungsanleitung

Stels

Stels 51131 Bedienungsanleitung

Bushranger

Bushranger RJX01 Bedienungsanleitung

Clarke

Clarke CTJ2500QLG Installations- und Betriebshandbuch

Valex

Valex 1650520 Bedienungsanleitung

Pfaff

Pfaff Merkur M0 Bedienungsanleitung

Beta

Beta 3050/K Beilage

Sealey

Sealey 1050CXHV Bedienungsanleitung

Jung

Jung JH Series Bedienungsanleitung

URIAH

URIAH UC200020 Bedienungsanleitung

Kennedy

Kennedy KSJ010 Bedienungsanleitung