Pro-Lift F1650 Bedienungsanleitung

OWNER’S MANUAL

WORKING LOAD LIMIT 1650KG

• Safety Instructions

• Operation Procedures

• Maintenance Procedures

READ RULES FOR SAFE OPERATION AND INSTRUCTIONS CAREFULLY

Model: F1650

THIS NEW JACK CONFORMS TO MANDATORY

ASNZS 2615:2004 STANDARD

Shinn Fu (Australia) PTY. LTD.

15 Viewtech Place, Rowville, Victoria 3178, Australia

FLOOR JACK

WARNING: THE JACK MUST BE USED ONLY ON HARD

LEVEL SURFACES AND BE FREE TO ROLL DURING

LIFTING AND LOWERING. DO NOT GET UNDER A

VEHICLE THAT IS SUPPORTED BY A TROLLEY JACK

- USE SUPPORT STANDS.

SAFETY INSTRUCTIONS

INSPECTIONS

This hydraulic trolley jack is designed to be used with a 60mm diameter head cap, and

a handle length of 700mm length.

1. BEFORE EACH USE

Visual inspection should be made before each use of the trolley jack for abnormal

conditions such as cracked welds, leaks and damaged, loose, or missing parts.

2. AFTER EACH USE

Trolley jack should be inspected immediately if the lift is believed to have been

subjected to an abnormal load or shock. It is recommended that inspection be made

by manufacturer’s or supplier’s authorised repair facility.

3. ANNUAL INSPECTION

Annual inspection of the trolley jack is recommended and is recommended to be

made by the manufacturer’s or supplier’s authorised repair facility to ensure that

your trolley jack is in optimum condition.

RECOMMENDATION FOR SAFE USAGE OF THE JACK

1. The hydraulic trolley jack should be used on a hard level surface and be free to roll

during lifting and lowering.

2. The unlifted wheels of the vehicle should be chocked.

3. The load should be centrally located on the head cap.

4. No person should remain in a vehicle that is being lifted.

5. The hydraulic trolley jack should be used for lifting and lowering only; the raised

vehicle should be supported on vehicle support stands.

6. No person should get bodily under a vehicle that is supported by a hydraulic trolley

jack.

7. The vehicle manufacturer owner’s manual should be consulted prior to the lifting of

the vehicle.

8. Make sure that lift point is stable and properly centred on jack saddle.

9. Transmission should be in gear (or park for automatic transmissions) and the

emergency brake should be engaged.

10. Familiarise yourself thoroughly with this owner manual before operation to prevent

damage to jack and property, or personal injury.

CAUTION BEFORE USE

Due to shipment and/or handling air can be trapped in the hydraulic system, which can

interfere with the jacks lifting. To release air from the hydraulic system:

• Open release valve by turning the jack handle counterclockwise.

• Remove the oil filler plug from the cylinder.

• Rapidly pump jack handle through several full strokes.

• Replace the oil filler plug into the cylinder.

! !

WARNING:

• THE JACK MUST BE USED ONLY ON HARD LEVEL SURFACES AND BE FREE

TO ROLL DURING LIFTING AND LOWERING

• DO NOT GET UNDER A VEHICLE THAT IS SUPPORT BY A TROLLEY JACK

- USE SUPPORT STANDS

OPERATION PROCEDURES

Before using

1. Remove cover plate (friction fit, easily

removes) and open Oil Filler Plug to

allow air to be vented.

2. Open Release Valve with the handle.

Turn it counterclockwise.

3. Pump handle rapidly several times.

4. Close oil filler plug, then replace cover

plate.

5. No person should remain in the vehicle

that is being jacked.

Raising the jack

1. Place car in park, apply emergency

brake and chocked wheel in “straight

ahead” position.

2. Close Release Valve TIGHTLY (by

applying handle turning clockwise).

3. Position jack under load so that saddle

will contact load firmly and is centered

so it cannot slip. Avoid off-centered load

on the saddle.

4. Operate jack handle until saddle almost

approaches to contact with load. Once

again check to see that the saddle is

correctly positioned.

5. Raise load to desired height. Transfer

the load to Jack Stands immediately.

Lowering the jack

Open Release Valve VERY SLOWLY (by

applying handle turning counterclockwise)

and never more than 1/2 turns. When

Release Valve is opened, saddle will lower

easily due to spring tension on the Lift Arm

Assembly.

Moving the jack

Place handle in Handle Sleeve. DO NOT

move the jack when handle is on the

Release Valve as this may cause damage

to the pump unit of the jack. DO NOT move

the jack when it is under load.

CAUTION

Keep clear from the vehicle when

lowering the jack.

PARTS KEY

1. Oil Filler Plug

(Not shown, under Cover Plate)

2. Castor

3. Base

4. Release Valve

5. Pump Cylinder

6. Pump Piston

7. Handle Sleeve

8. Cover Plate

9. Lifting Arm

10. Saddle

11. Link Rod

12. Front Wheel

13. Frame

14. Middle Spindle

15. Reservoir

(Not shown, under Cover Plate)

16. Handle

MAINTENANCE PROCEDURES

MAINTAINING OIL LEVEL

Important Note:

When adding or replacing oil, always

use a good grade Hydraulic Jack Oil (or

transmission oil, turbine oil etc.). Avoid

mixing types of oil. DO NOT use Brake

Fluid, Alcohol, Glycerine, Detergent, Motor

Oil or Dirty Oil. Improper fluid can cause

serious internal damage to Jack.

ADDING OIL:

With saddle fully lowered & jack on level

ground, remove cover plate then open

Oil Filler Plug. Oil level should be approx.

12mm below valve hole. If low, add oil

as needed then close Oil Filler Plug and

replace cover plate.

REPLACING OIL:

For better performance and longevity,

replace oil supply once a year. To drain

oil, remove cover plate, open Oil Filler

Plug and loosen the Release Valve by

applying handle turning counterclockwise.

BE VERY CAREFUL not to permit dirt or

foreign matter to get into the system. Close

Oil Filler Plug and replace cover plate.

SPECIFICATIONS

Working Load Limit: .......................................................................................... 1650Kg

Jack Dimension : .............................................................. 550mm x 210mm x 130mm

Height Lowered : ...............................................................................................140mm

Height Raised : ................................................................................................. 381mm

Oil Capacity : ...................................................................................................90+/-5cc

Net Weight : .......................................................................................12.5Kg. (approx.)

210mm

550mm

65mm36mm

381mm

140mm

TROUBLESHOOTING

(USING JACK WITHIN RATED LOAD CAPACITY)

POSSIBLE JACK PROBLEMS

POSSIBLE CAUSES AND

SOLUTIONS

(Refer to Operation and

Maintenance procedures

for detailed information)

Release valve not tightly

closed.

To close or tighten, turn

release valve clockwise.

Air is in hydraulic system.

Release air from system.

Oil level is low in jack

Add oil as required

1. Oil reservoir is over-filled

Drain out some oil.

2. Lubrication of moving

parts is necessary.

Power unit is

malfunctioning.

Replace the power unit.

Jack will

not lift

load

Jack will

lift load,

but will

not hold

Jack will

not lower

completely

Poor jack

lifting.

Pump

feels

spongy

Jack will

not lift to

full height

Handle

raises by

itself when

jack is

under load

LUBRICATION

• Add lubrication oil to all moving parts

every 3 months.

PREVENTING RUST

• Check Piston Rod & Pump Piston

every 3 months for any signs of rust or

corrosion. Clean as needed and wipe

with an oily cloth.

• When not using the jack, always leave

the saddle & pump piston all the way

down.

KNOW YOUR JACK

Compare these illustrations with your

jack before operation and/or oil level

maintenance to become familiar with

the location of jack components.

RELEASE

VALVE

PUMP PISTON

DOWN

PROPER OIL

LEVEL

OIL FILLER

PLUG

PISTON ROD ALL

THE WAY IN

Inhaltsverzeichnis

Andere Pro-Lift Jack Handbücher

Pro-Lift

Pro-Lift F-2525 Gebrauchsanweisung

Pro-Lift

Pro-Lift B-002D Gebrauchsanweisung

Pro-Lift

Pro-Lift G-737 Gebrauchsanweisung

Pro-Lift

Pro-Lift B-002NC Gebrauchsanweisung

Pro-Lift

Pro-Lift F2000 Bedienungsanleitung

Pro-Lift

Pro-Lift F-2332 Gebrauchsanweisung

Pro-Lift

Pro-Lift F1500A Bedienungsanleitung

Pro-Lift

Pro-Lift PL3300 Gebrauchsanweisung

Pro-Lift

Pro-Lift F1500A Bedienungsanleitung

Pro-Lift

Pro-Lift F-2330BMC Gebrauchsanweisung

Pro-Lift

Pro-Lift F1800A Bedienungsanleitung

Pro-Lift

Pro-Lift B-1850 Bedienungsanleitung

Pro-Lift

Pro-Lift F2000A Bedienungsanleitung

Pro-Lift

Pro-Lift F1800 Bedienungsanleitung

Pro-Lift

Pro-Lift SG-5625 Gebrauchsanweisung

Pro-Lift

Pro-Lift F1650A Bedienungsanleitung

Pro-Lift

Pro-Lift G-4630 Gebrauchsanweisung

Pro-Lift

Pro-Lift F1400 Bedienungsanleitung

Pro-Lift

Pro-Lift Garage in a Box Gebrauchsanweisung

Pro-Lift

Pro-Lift T-9446 Gebrauchsanweisung

Pro-Lift

Pro-Lift G-4630JSC Gebrauchsanweisung

Pro-Lift

Pro-Lift PRO-A1200 Bedienungsanleitung

Pro-Lift

Pro-Lift PL1002 Bedienungsanleitung

Pro-Lift

Pro-Lift T-9400 Gebrauchsanweisung

Beliebte Jack Handbücher anderer Marken

Omega Lift Equipment

Omega Lift Equipment 18122C Gebrauchsanweisung

Pittsburgh

Pittsburgh 58816 Montageanleitung

Unimec

Unimec TP Bedienungsanleitung

Sonic

Sonic 4800703 Bedienungsanleitung

BGS technic

BGS technic 70039 Bedienungsanleitung

TradeQuip

TradeQuip 1128T Bedienungsanleitung

VEVOR

VEVOR TJD-12000SP-F Bedienungsanleitung

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Bedienungsanleitung

Stels

Stels 51131 Bedienungsanleitung

Bushranger

Bushranger RJX01 Bedienungsanleitung

Clarke

Clarke CTJ2500QLG Installations- und Betriebshandbuch

Valex

Valex 1650520 Bedienungsanleitung

Pfaff

Pfaff Merkur M0 Bedienungsanleitung

Beta

Beta 3050/K Beilage

Sealey

Sealey 1050CXHV Bedienungsanleitung

Jung

Jung JH Series Bedienungsanleitung

URIAH

URIAH UC200020 Bedienungsanleitung

Kennedy

Kennedy KSJ010 Bedienungsanleitung