MT-7029N
Noise-Filtering Network PoE Toner & Probe
Thank you for purchasing and using the Pro'sKit MT-7029N Noise-
Filtering Network PoE Toner & Probe. Please read the instruction
manual carefully before using this product, and keep it properly for
future review.
OVERVIEW
MT-7029N is the new upgrade version with a better noise filtering
design. The high-frequency filter circuit technology eliminates the
noise and anti-interference line tracer. Suitable for ordinary network,
PoE network, UTP / STP cable search,and positioning. The new
function can locate the port with flashing signals; check the crimping
quality of the plug single-way; be able to trace the wire & cable mapping
at the same time. Ideal for all installation & maintenance jobs.
INTRODUCTION
Figure1. MT-7029N Transmitter Diagram
1.
ΕFlashΖ:Network port flashing function button.
1.ΕCrimpingΖ:RJ45 Plug crimpingqualitytest button.
ΕTEL/POLΖ:Phone line polarity function button.
1.Battery cover.
Figure 2. MT-7029N Receiver Diagram
1. Probe:Wire tracing and NCV detection.
2. LED light.
3. Power ON/OFF indicator.
4. NCV indicator.
5. Signal status indicator.
6. Volume control.
7. Earphone socket (ĭPP).
8. Function switch (LED light/NCV/OFF/SCAN mode).
9. Speaker.
10. ΕΖLocating and tracing cables function button
11. Ε1~8/GΖCable map & Shielded indicator
12. RJ45 (8 pin) / RJ11 (6/4/2 pin) cable mapping test socket.
13. Battery cover
SPECIFICATIONS
MT-7029N Transmitter specifications
Wire tracing
RJ45 Lan cable Cat5, 5e, 6, 7(UTP/STP),
RJ11/12 telephone cable
Voltage8Vp-p
Frequency455KHz
Tracing distance 600m
Cable
mapping
RJ45 Test/Scan socket for RJ45、RJ11/RJ12
locating Individual wire pairs
8+1 LED indicators.
Crimping Test
,
1dual color LED: POL-˄Green˅/ POL+˄Red˅
About 7.0V; power indicator will flash.
DC 60V
Battery
9V (NEDA 1604/6F22) x1pcs
Working
current
Tracing/Cable map/Crimping <35mA; Port flash
MT-7029N Receiver Specifications
1 LED indicator &speaker
RJ45 socket
8+1 LED indicators
1 LED indicator & speaker (AC 90-1000V)
Earphone ʅ3.5mm socket
About 7.0V; power indicator will flash.
9V (NEDA 1604/6F22) x1pcs
Working
Tracing <200mA; lighting<50mA
weight
Accessories
RJ45 cable patch cords x2, RJ11 cable patch
cords x2,RJ11 to alligator clips patch cord x1,
earphone x1, storage bag, user manual.
OPERATION
MT-7029N Transmitter˖
Do not connect with DC 60V live circuit equipment or it might
cause damage.
ýCable Mapping
This function is to check the network cable connection is good or not.
To connect the cable with the transmitter and receiver, by viewing the
transmitter and receiver 1-8 / G indicators to verify the network cable
connection situation. It can test the network cable straight, short,
open, and crossover. You can also connect the transmitter directly to
the network switch or the network interface test the cable connection.
The operation is as follows:
1. Insert the cable into the transmitter theΕTest/ScanΖsocket and the
other end into the receiver socket.
2. Press theΕΖbutton,the power indicator is on.
3. Press theΕTest / ScanΖbutton , theΕTestΖindicator will light, and
the cable mapping will be started automatically.
4. There are four results as following examples:
zStraight:
T: 1-2--4--6-7-8 T: 1-2--4--6-7-8-G
R:1-2--4--6-7-8 R:1-2--4--6-7-8-G
zCrossover:
T: 1-荜--4--6-7-8 T: 1 -2--4-Ļ-6-7-8
R:1-2--4-Ļ-6-7-8 R:1-荜--4--6-7-8
zOpen:
T: 1-X--4--6-7-8
R:1-X--4--6-7-8
zShort:
T: 1-2--ĺ--6-7-8 T: 1 -2--4-Ļ-6-7-8
R:1-2--ĺ-Ļ-6-7-8 R:1-2--ĺ-Ļ-6-7-8
The FDEOHPDSindicators
3&/('aOLJKWXSDQGWKHRWKHUV DUHRII
3&/('a OLJKWXSDQGWKHRWKHUV DUHRII
3&/('aOLJKWXSDQGWKHRWKHUs DUHRII
ýWire Tracing
This function is using the transmitter to send the signals and the receiver
to receive the signals with an audio alarm. It has strong noise-filtering
design, and you can identify the correct wire easily.Specific operations
are as follows:
1. Insert the tracing wire into the transmitterΕTest / ScanΖorΕPOL /
ScanΖsocket.
2. Turn the transmitter, pressΕT est / ScanΖbutton twice, the ΕScanΖ
indicator will light,and the transmitter will send the signals.
3. The transmitter will send the signals and check the cable status at
the same time. You will know each line status through the indicator
led (1-8).
4. Turn on the receiver and you will hear a beep sound means the
machine is on. The power indicator will light.
5. Rotate the adjustable sensor knob clockwise to turn the sensitivity
to the maximum. Press & hold theΕSCANΖbutton. The receiver will
be receiving the signals from the transmitter, once it receives the
signals, it will send audio alarm, so you can find the correct wire.
6. When tracing the wire, you need to press & hold the receiver
ΕSCANΖbutton. The receiver will stop receiving signals once you
release the button. Kindly remind you to remove the battery after
using it to save energy.
7. You might receive signals from more than one wire. In this case,
please try to rotate the adjustable sensor knob counter-clockwise
to lower the sensitivity, and you will be able to find the correct wire.
ýPlug Crimping Quality Check
This function can single-way check RJ45/RJ11 plug crimping quality at
RQHVLGH DQGQRQHHGWRFRQQHFWWRWKH RWKHUVLGH ,W¶V convenient &
smart.
1. Insert the network cable into the transmitterΕCrimpingΖsocket.
2. Press theΕΖbutton to turn on the transmitter and press the
ΕCrimpingΖbutton.
3. The transmitter will start to check the cable pin to pin and the
indicator ofΕCrimpingΖ1-8 will light up if all the connection are
JRRG7KHRQHGRHVQ¶WOLJKWXSPHDQVWKHFRQQHFWLRQLVGRZQ
For example as follows, the 2 & 5 pin are broken.
1-X--4-X-6-7-8
ýPort Flash
This function will help you to locate the port quickly, the transmitter will
send the flashing signals, so you can easily determine the correct port.
1. Insert the network cable into the transmitterΕTest/ScanΖsocket and
the other side to network switch.
2. Press the ΕΖbutton to turn on the transmitter, press theΕFlashΖ
button , theΕFlashΖindicator will light or flash.
3. Check the indicatorson the network switch,If the indicator flash
around every 3 seconds, the corresponding port is the correct port.
ýTelephone Line POL +/-
This function is suitable for testing and determining the polarity of a
telephone line.
1. Insert the alligator clip RJ11 cable into the transmitter ΕPOL/ScanΖ
socket.
2. Press the ΕΖbutton to turn on the transmitter, press the
ΕTEL/POLΖbutton , theΕPOLΖindicator will light.
3. Clip the red and black alligator each side of the telephone line, and
the indicator will light.
4. If the indicator light is red, the red alligator is on the positive pole &
the black alligator is on the negative pole. If the indicator light is
green, then the red alligator is on the negative pole & the black
alligator is on the positive pole.
ýNon-contact Voltage Detection (NCV)
This function is used to determine if there is a live circuit, the detection
range is AC90-1000V (50 / 60Hz).
zTurn on the receiver and switch to the NCV position, move the
receiver probe close to the test subject. If the AC voltage is detected,
the speaker will send an audio alarm in different frequency. The
higher frequency the higher voltage is.
Note:
zThis function is for reference, the voltage may still remain even there
is no detection. There are many possible factors might block the
detection.
zThere are some factors (like flashlight and motor) might also trigger
non-contact voltage detection.
ΕCrimpingΖ:RJ45 plug crimpingqualitytest socket.
ΕPOL/ScanΖ:Scan & telephone line test socket.
ΕTest/ScanΖ:RJ45cablemaptest & scansocket.
Ε1~8/GΖ:Cable map & Shielded indicator.
Ε1~8Ζ:RJ45 plug crimping quality testindicator.
ΕPower/BAT LOWΖ:Power ON/OFF & Battery low indicator.
Function indicator:
ΕTestΖ:Cable map & Shielded function indicator.
ΕScanΖ:Locating and isolating cables function indicator.
ΕFlashΖ:Network port flashing function indicator.
)XQFWLRQLQGLFDWRU
ΕCrimpingΖ:RJ45 plug crimping test function indicator.
ΕPOLΖ:Telephone line +/ -pole test function indicator.
ΕPOLˉ/GˈPOLˇ/RΖ:Phone line polarity indicator.
Ε Ζ:Power ON/OFF button.
ΕTest/ScanΖ:Cable map test &Scanfunction button.
1.
