PROFESSIONAL HYDRAULIC JACKS 40105 Bedienungsanleitung
OPERATOR’S MANUAL
Model 40105
5 TON
SIDE PUMP BOTTLE JACK
PROFESSIONAL HYDRAULIC JACKS
1531 West Mo awk Drive P one 715-453-9602 Customer Service 800-995-2250
Toma awk, WI 54487 Fax 715-453-6020 www.projacks.com
Specifications
Minimum
Height
Maximum
Height Lift
Extensi n
Screw
Net
Weight
8” 16” 5-1/4” 2-3/4” 10 lbs
T is is a lifting device only. It is designed to lift part of total ve icle (one w eel or axle).
Always wear safety glasses w en using t is equipment.
Center load on saddle before lifting.
Never work on, under or around load until it is properly supported.
Transfer t e load immediately to appropriately rated jack stands.
Do not use t is product for any purpose ot er t an t at for w ic it was intended.
It is t e owner’s responsibility to keep labels and instructional material legible and available.
Replacement labels and manuals are available from Professional Hydraulic Jacks, Inc.
Failure to read t ese and all ot er warnings pertaining to t is product can result in sudden loss of
lifted load resulting in deat , personal injury or property damage.
Be sure all tools and personnel are clear before lowering load. Quickly opening and closing t e release
valve as t e load is being lowered create dangerous dynamic s ock loads. T e resulting overload may
cause ydraulic system failure, w ic could cause severe personal injury and/or property damage.
Operating Instructions
1. Before operating, estimate t e weig t of t e load.
2. Do not overload t e jack beyond its rated capacity.
3. Select point of action according to t e gravitational center place t e jack on t e ard ground if
necessary, places a ard plank under t e jack so as to avoid tottering or falling during operation.
4. Before operating jacks, first insert t e notc ed end of t e andle into t e release valve. Turn t e
operating andle clockwise until release valve is closed. Do not over tig ten t e valve.
5. Insert operating andle into t e socket and t e ram is steadily raised by t e up and down movement
of t e andle and t e load is raised. T e ram will stop rising w en t e required eig t is reac ed.
6. Lower t e ram by turning t e release valve counter-clock wise wit notc ed end slacken it slowly
w en a load is applied, or accidents can occur.
7. W en more t an one jack is used at t e same time it is important to operate t e different jacks at an
equal speed wit equal load. Ot erwise, t ere is danger of t e entire fixture falling.
8. At an ambient temperature from 27F to 113F use mac ine oil (GB443-84) N15. At an ambient
temperature from -4F to 27F use synt etic spindle oil (GB442-64). Sufficient filtered ydraulic oil s ould
be maintained in t e jacks; ot erwise t e rated eig t cannot be reac ed.
9. Violent s ocks must be avoided during t e operation.
10. User must operate t e jack correctly according to operating instructions: If t e jack as some quality
problems it cannot be operated.
Parts List
Item N Descripti n Part N Quantity
1 Release valve lever 102001 1
2 Base 102002 1
3 O-ring 102003 1
4 Hydraulic cylinder 102004 1
5 Ram 102005 1
6 Hydraulic oil 102006 1
7 Oil- tig t tank 102007 1
8 Extension screw 102008 1
9 Top cap 102009 1
10 Pump plunger 102010 1
11 Pump body 102011 1
12 O-ring 102012 1
Inhaltsverzeichnis
Andere PROFESSIONAL HYDRAULIC JACKS Werkzeuge Handbücher
