ProFusion HA11-20M Bedienungsanleitung

Forced Air Bathroom Heater

Owner’s Manual

Model：HA11-20M

PLEASE READ AND SAVE THESE INSTRUCTIONS

Customer Service: 1-888-538-0082

Soutien technique en français: 1-866-206-0888

Service Email: service@hena.ca

Table of Contents

1. Important Instructions………………………………………..…1

2. Outlook and Specifications ……………………………………4

3. Installation…… ………………………………………….………4

4. Electric Wiring Connection …………………………..…….…6

5. Operation ……………………………………………….……… 6

6. Safety Features………………………………………….………7

7. Cleaning the Heater……………………………..….………… 8

8. Storage….………………………………………….…………… 8

IMPORTANT INSTRUCTIONS

Before installing and using this bathroom heater, basic precautions should always be followed

to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before installing and using this heater.

2. This product must be installed by a certified master electrician, in accordance with all local

& national building codes.

3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces

and close to air-flow outlet. Keep flammable materials, such as furniture, pillows, bedding,

papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep

them away from the sides and rear.

4. Caution is necessary when this heater is used by or near children or invalids and

whenever the heater is left operating and unattended.

5. Always cut off the power source to the heater when not in use.

6. Do not operate heater with a damaged cord or after the heater malfunctions, has been

dropped or damaged in any manner. Discard heater or return to an authorized service

facility for examination and/or repair.

7. Do not use outdoors. Do not allow water to splash on the heater.

8. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this

may cause an electric shock or fire, or damage the heater.

9. To prevent a possible fire, do not block air intakes or exhaust in any manner.

10.A heater has hot and arcing orsparking parts inside. Do not use it in areas where gasoline,

paint, or flammable liquids are used or stored.

11.Use this heater only as described in this manual. Any other use not recommended by the

manufacturer may cause fire, electric shock, or injury to persons.

12.Service of the heater other than cleaning should be performed by an authorized service

centre. No user serviceable parts inside.

13.This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play

with the appliance.

SAVE THESE INSTRUCTIONS

Outlook and Specifications

Model Voltage Frequency

Power Current

HA11-20M

208V/240V

60Hz 1500W / 2000W 8.3A

Installation

WARNING: This heater requires hardwire installation (no plug). The installation of this

product must be carried out by a Certified Electrician and in accordance with all local

and national electrical codes.

CAUTION: Risk of fire –Do not operate without complete the installation.

Before using, the heater must be correctly installed.

1. It must be secured to a wall, more than 24 in (610 mm) away from the floor and adjacent

walls (Fig. 1). Do not install the heater below an electrical convenience outlet. Also,

the unit cannot be covered or hidden by a door.

2. Draw a horizontal line and a vertical centre line on the wall (Fig. 2).

On the horizontal line, drill two holes 76 mm (3") from the centre line with a diameter as

that of the wall plugs provided, then drill another hole on the centre line below the

horizontal line, apart 398 mm (Fig.2).

3. Insert three wall plugs.

4. Drive two screws provided into two upper wall plugs, leaving a gap of 5/16 in (8 mm)

between the screw head and the wall (Fig. 2).

Fig.1 Fig.2

5. Hang the unit on the two installed screws while holding it securely in your hands;

CAUTION! Before letting go of the unit, check that it is securely hung on the two

screws.

5. Secure the unit with the third screw at the bottom. The illustration (Fig.3)

6. indicates the airflow generated by the heater.

This air corridor must remain clear in order to allow good air circulation and to ensure that the

unit operates efficiently.

Leave at least 12 in (305 mm ) in front of the unit.

Electric Wiring Connection

CAUTION! Cut off power supply at circuit breaker/fuse before proceeding to the wiring

connections.

This product must be connected by a certified electrician, according to the electrical and

building codes effective in your region.

1. Make sure the live cable from the power source

connect with the black cable at the back of the unit

the neutral cable connect with the white cable and the

grounding cable connect with the green & yellow cable.

(fig.4).

2. Installation of this product must be made in

accordance with all national and local building codes.

3. The electric connections must be made with a

12-gauge 2-conductor wire complete with ground

(Fig.4).

Operation

It is normal for the heater to emit some odour when it is turned on for the first time, or after

having not been used for a long period of time. This will disappear when the heater has been

on a short while.

The fan heater has two knobs, one for the 60-minute timer and one for the thermostat.

The unit has two operating modes.

1. ROOM WARM-UP WITH TEMPERATURE CONTROL

Turn the thermostat knob clockwise until a clicking noise is heard, the unit is turned on at a

power of 1200 W and the pilot light turns on. The thermostat maintains the required room

temperature by automatically turning on and off the fan heater. The more you turn the knob

clockwise, the higher the constant temperature will be.

The thermostat maximum setting is about 35 °C-40℃, and the minimum setting about 5 °C.

Setting thermostat :

With a room temperature above 35 °C-40℃, to what a extent depend on a room size, it is

normal for the thermostat to not turn on the fan heater, even at the maximum setting. With a

room temperature too low (under 5 °C), it is normal for the thermostat to maintain the unit on,

even at the minimum setting. This is a special feature of heater to maintain the temperature

above freezing to avoid the temperature dropping under approx. +5°C.

To optimize thermostat usage:

•Set the thermostat to the maximum setting and operate the unit until a comfortable

temperature is reached.

•Then, turn the thermostat knob counter-clockwise until a click is heard (the unit is turned off).

•Slightly turn (just a little) the thermostat knob clockwise.

•At this setting, the thermostat maintains the chosen room temperature.

2. QUICK ROOM WARM-UP

With the room temperature set at the required level, turn the timer knob to select the required

operating time. The unit operates at 2000 W for the set time to quickly heat the room and then

maintains the room temperature set by the thermostat at a power of 1200 W.

Safety Features

1. Pilot lamp

This appliance has a pilot lamp to indicate this appliance is switched on. When you are not

using the heater, cut off the main power source to the heater.

2. Overheating protection

The appliance has dual internal over-heat safety device,

which automatically switches the heater off the unit overheats.

In the event the unit overheats, the built-in protection system

automatically deactivates the heating elements effectively,

however the pilot lamp is still on.

2.1First protecting device

Normally a built-in thermal cut out play the role of such

protection at first, in this case the heating element stop

generating heat, but the motor remains running to cool down

the heater, and pilot lamp remains on.

To restart the unit you can follow below procedures.

ŸAfter cooling for about 10-15 minutes. Turn off the fan

heater by turning the thermostat knob counter-clockwise

until a click is heard or the pilot lamp is off, or simply cut

off the main power source to the heater.

ŸCheck if the dust filter is blocked and if so, clean and reinstall it.

ŸTurn the fan heater on again and check for proper operation. If you cannot get your unit to

work, bring it back where you purchased it or have it verified by a certified electrician.

2.2 Second protecting device

If appear an extremely overheat or malfunction of thermal cut out, a built-in thermal link will

burn out act as a second protection, in this case both heating element and the motor stop

working, no heat, no air flow. This situation seldom happen, if happen, you can only bring it

back where you purchased it to replace the thermal link.

Cleaning The Heater

1. Your unit has a filter protecting the heating elements against dust and dirt.

2. The filter can only be removed and inserted from the left side.

3. For optimal operation, we recommend cleaning the filter once every 2 months and making

sure to reinstall it on the unit. Regularly vacuum the front grille to remove the dust.

Accumulated dust and lint at the air outlet can reduce the unit’s performance and even

damage it. To clean the unit, use a slightly damp cloth.

Note that cigarette smoke can cause unit fading, despite the cleaning.

4. Always cut out the main source to the heater and allow it to cool down before cleaning.

5. Clean the outside of the heater by wiping with a damp cloth and buff with a dry cloth.

6. Do not use any detergents or abrasives and do not allow any water to enter the heater.

Storage

When the heater is not used for a long periods of time, it should be protected from dust by

being repacked and be stored in a clean dry place.

Chaufferette à air pulsé pour salles de bains

Guide de l’utilisateur

Modèle ：HA11-20M

VEUILLEZ LIRE ET CONSERVER

CES INSTRUCTIONS

Service à la clientèle: 1-888-538-0082

Soutien technique en français: 1-866-206-0888

Courriel de service: service@hena.ca

Table des matières

1. Instructions importantes……………………………………..…11

2. Apparence et caractéristiques …………………………………12

3. Installation…… ………………………………………….………12

4. Branchements et câblage électriques ..……………..…….…14

5. Fonctionnement.……………………………………….……… 14

6. Caractéristiques de sécurité .………………………….………15

7. Nettoyage ......................…………………………….…………16

8. Entreposage.…………………………………….…………… 16

Inhaltsverzeichnis

Sprachen:

Andere ProFusion Heizung Handbücher

ProFusion

ProFusion PH-9100WRN Bedienungsanleitung

ProFusion

ProFusion PH-960N Bedienungsanleitung

ProFusion

ProFusion HA24-50MB Bedienungsanleitung

ProFusion

ProFusion Salamander PS-10241P Bedienungsanleitung

ProFusion

ProFusion WH-50B Bedienungsanleitung

ProFusion

ProFusion PH-9100WN Bedienungsanleitung

ProFusion

ProFusion HFU15-E Bedienungsanleitung

ProFusion

ProFusion TV15LR Bedienungsanleitung

ProFusion

ProFusion HA24-75MB Bedienungsanleitung

ProFusion

ProFusion HA22-48M Bedienungsanleitung

ProFusion

ProFusion QH-1 Betriebsanleitung

ProFusion

ProFusion PH-931 Bedienungsanleitung

ProFusion

ProFusion EH-4601 Bedienungsanleitung

ProFusion

ProFusion PH-960XNR Bedienungsanleitung

ProFusion

ProFusion EH-4604 Bedienungsanleitung

ProFusion

ProFusion GD9315BC1-N Bedienungsanleitung

ProFusion

ProFusion PH-9100WS Bedienungsanleitung

ProFusion

ProFusion NDB-1Y Bedienungsanleitung

ProFusion

ProFusion Ceiling mounted utility heater Bedienungsanleitung

ProFusion

ProFusion DQ1016A Bedienungsanleitung

ProFusion

ProFusion SHAG-L02F Bedienungsanleitung

ProFusion

ProFusion PH-934 Bedienungsanleitung

ProFusion

ProFusion H-4439 Bedienungsanleitung

ProFusion

ProFusion HA24-50E Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung