Projecta INVCHRD-BT Bedienungsanleitung

INVERTER CHARGER

BATTERY MONITOR

P/No INVCHRD-BT

WARNINGS – IMPORTANT PLEASE READ

• Do not disassemble the monitor. Take to a qualified person if the unit requires repairing.

1 2 3 4

5 6 7

8 9 10 11 12 13 14

PRODUCT OVERVIEW

NO DEFINITION DESCRIPTION

1 Solar To indicate solar charger is charging

2 Invert To indicate inverters is working

3 Bypass To indicate Grid or generator is presenting

4 Charge To indicate battery is charging

5 Overload alarm To indicate when inverter is overloaded

6 Battery low voltage alarm To indicate when inverter reach under-voltage

7 Over temperature alarm To indicate when inverter is over-temperature

8 Load percentage To indicate the percentage of actual load power against

rated power of inverter installed

9 Inverter ON/OFF switch To turn Inverter ON or OFF

10 Scroll up / Back LCD displaying value

11 LCD screen

12 Scroll down / conﬁrm button To scroll down to next item. Or as function of conﬁrmation of

your selection and conﬁguration. With long press for 3 secs.

13 Mute button To mute or unmute the alarm

14 Battery SOC To indicate battery state of charge

DISPLAY INFORMATION IN VALUE INFORMATION AREA

V Battery Voltage

A Battery Current

Battery SOC

FEATURES

• Device allows users to remotely monitor and control Projecta Inverter Chargers

• Displays battery voltage*, current*, inverter load percentage, AC input/output voltage, frequency and power

• Battery status can be monitored via smart phone or tablet if connected.

• Inbuilt intelligent battery monitoring technology

* Will show battery information where a Projecta HD sereies battery is connected to the system.

INSTALLATION

Step 1: Cut holes on mounting surface following the cut-out dimension of solid line area in the below diagram

Step 2: Place the INVCHRD-BT in position properly and fix the INVCHRD-BT by 4pcs M3*12 screws

110

103

83.5

CONNECTION

• Use the cable with RJ45 terminal to connect the INVCHRD-BT to the ComMON terminal of the inverter charger

in Fig.1.

• Use the cable with RJ45 terminal to connect the INVCHRD-BT to the ComMON terminal of the inverter charger

and connect the ComSync or ComSyncIn terminal of the inverter charger to the CAN/RS485 terminal of the HD

Series lithium battery in Fig.2.

ComMON

ComSync/

ComSyncIn

CAN/RS485

ComMON

Fig. 1 Fig. 2

APP

INVCHRD-BT Support APP can be downloaded on the Google Play Store for Android Devices and the AppStore

for Apple Devices.

DETAIL LED DISPLAY INFORMATION OF BATTERY SOC

Battery Status SOC LED 1 LED 2 LED 3 LED 4 LED 5

Charging

SOC=100% Illuminate Illuminate Illuminate Illuminate Illuminate

80%≤SOC < 100% Illuminate Illuminate Illuminate Illuminate Flash

60%≤SOC < 80% Illuminate Illuminate Illuminate Flash Off

40%≤SOC < 60% Illuminate Illuminate Flash Off Off

20%≤SOC < 40% Illuminate Flash Off Off Off

0%≤SOC < 20% Flash Off Off Off Off

Discharge

80%≤SOC ≤100% Illuminate Illuminate Illuminate Illuminate Illuminate

60%≤SOC < 80% Illuminate Illuminate Illuminate Illuminate Off

40%≤SOC < 60% Illuminate Illuminate Illuminate Off Off

20%≤SOC < 40% Illuminate Illuminate Off Off Off

0%≤SOC < 20% Illuminate Off Off Off Off

SOC=0 Off Off Off Off Off

DISPLAY INFORMATION VALUE AREA

Display Information Item

Battery V Battery voltage

A Battery current

AC Output

kW AC output power

Hz AC output frequency

V AC output voltage

A AC output current

AC Input

kW AC Input power

Hz AC Input frequency

V AC Input voltage

A AC Input current

Solar kW PV power

V PV voltage

CONFIGURATION ITEMS AND SETTING VALUES

Display Information Configuration Item Default Setting and Setting Step

Battery

VAbsorption Voltage, ON Step: 0.1V, Default: 14.1V

VFloat Voltage, Flashing Step: 0.1V, Default: 13.6V

A Max Charge Current Step: 1A, Default: 30A

AC Output VOutput Voltage Step: 10V, Default: 240V

Hz Output Frequency Default: 50/60Hz

AC Input A AC Input Rating Step: 1A, Default: 32A

Buzzer Alarms Buzzer ON or OFF Default: ON

Enable SOC Display

SOC lights and battery back-

ground lights are all ﬂash

ON: Enable SOC display

OFF: Disable SOC display

Default: ON

Enable Screen Off Function

Power lights and battery back-

ground lights are all ﬂash

ON: Enable the Screen Off Function

OFF: Disable the Screen Off Function

Default: OFF

NOTE: Once the Screen Off function is enabled, the screen will automatically go off if there is no key operation for three

minutes. If the inverter status changes or an alarm occurs, it will be restarted keep the screen on for three minutes.

Note: Solar is for the INVCHR3-48V

with built in MPPT

CONFIGURATION

Step 1. To enter into the configuration: Press

scroll down/confirm button for 2 seconds.

Step 3. Long press the scroll down/confirm button

for 2 seconds to trigger on the configuration, the

number/icon will flash.

Step 5. Afterwards, long press the scroll down/

confirm button for 2 seconds to confirm the

configuration. The two bars (load ratio and

battery soc) will flash indicating the configuration

is in process.

Step 2. Then you can use scroll up or scroll down

button to choose the parameter you want to change.

Step 4. Use scroll up or scroll down button to change

the value.

Step 6. After you have done all configuration you

need, please press scroll up/return button for 2

seconds to exist configuration.

ERROR CODES

The INVCHRD-BT to Projecta’s Inverter Chargers

INVERTER ERROR CODES

CODE DISPLAY DESCRIPTION

101 U_Bus_OV Battery Over-Voltage

102 U_Bus_LV Battery Under-Voltage

103 U_Bus_HW_Pro DC Bus Hardware Under-Voltage

104 PSU_Fault Auxiliary Power Error

105 T_HS_OT Heat Sink Over-Temperature

106 T_TX_OT Transformer Over-Temperature

107 Sam_HD_Fault Sampling Fault

108 EEPROM_Fail EEPROM Fault

109 Output_ShortCut Output Short Circuit

110 Output_OverLoad Output Over-Load

111 CoolSys_Err Fan Error

112 U_BAT_Low_Deep Battery Deep Discharge

113 U_INV_LV Inverter Output Under-Voltage

114 Instant_OC_Soft Inverter Output Instant

115 EPO Emergency Stop

116 Rly_Err Relay Error

MPPT CHARGER CONTROLLER ERROR CODES

CODE DISPLAY DESCRIPTION

301 U_Bus_OV DC Bus Over-Voltage

303 U_Bus_OV HD Battery Over-Voltage(Hardware)

304 Buck_ShortCut Buck Short Circuit

305 I_Buck1_OC Buck1 Over-Current

306 I_Buck2_OC Buck2 Over-Current

307 T_Board_OT Control Board Over-Temperature

308 T_HS_OT Heat Sink Over-Temperature

309 PSU_LV Auxiliary Power Under-Voltage

310 PSU_LV_HD Auxiliary Power Under-Voltage(Hardware)

311 Sam_HD_Fault Sampling Fault

312 EEPROM_Fail EEPROM Fault

Note: Solar is for the INVCHR3-48V with built in MPPT

BMS ERROR CODES

CODE DISPLAY DESCRIPTION

ERR400 Module_OV Lithium battery is over voltage protection

ERR401 Module_UV Lithium battery is under voltage protection

ERR402 Module_OT Lithium battery’s temperature is too high

ERR403 Module_UT Lithium battery’s temperature is too low

ERR404 Discharge_OC Lithium battery’s discharge current is over current.

ERR405 Charge_OC Lithium battery’s charge current is over current.

ERR406 Module_INT_Err Lithium battery module fault

WARNING CODES

INVERTER WARNING CODES

CODE DISPLAY DESCRIPTION

001 U_BAT_OV Battey Over-Voltage Warning

002 U_BAT_LV Battery Under-Voltage

003 U_BAT_LV_Fault Battery Under-Voltage Protection

004 OverLoad Over-Load

005 NTC_HS_Fault Heat sink NTC Failed

006 NTC_TZ_Fault Transformer NTC Failed

007 T_BAT_OT Battery Over-Temperature

008 Fan_Fault Fan Error

009 ParConnect_Err Parallel Connection Error

010 ParComm_Err Parallel CAN Communication Error

011 Par_ID_Conﬂict Parallel ID Conﬂict

012 Par_ParaSet_Conﬂict Parallel Parameter Setting Conﬂict

013 Par_SyncTimeOut_Err Parallel Synchronization Timeout

014 ModeSet_Mismatch Working Mode Setting Mismatched

015 Par_OutputCircuit_Err Parallel Output Circuit Error

020 ACin_OV AC Input Over-Voltage

022 ACin_OF AC Input Over-Frequency

023 ACin_LF AC Input Under-Frequency

024 ACin_PhaseErr AC Input Phase Error

025 U_Neu_2_GND_Err AC Input Voltage Between Neutral and Ground Error

MPPT CHARGER CONTROLLER WARNING CODES

CODE DISPLAY DESCRIPTION

203 CUR_Limit MPPT Current Limit Warning

205 NTC_HS_Fault Heat Sink NTC Failed

207 Fan_Fault Fan Error

Note: Solar is for the INVCHR3-48V with built in MPPT

BMS WARNING CODES

CODE DISPLAY DESCRIPTION

050 Module_HV Lithium battery is over voltage

051 Module_LV Lithium battery is under voltage

052 Module_HT Lithium battery’s temperature is too high

053 Module_LT Lithium battery’s temperature is too low

054 Discharge_HC Lithium battery’s over current discharge.

055 Charge_HC Lithium battery’s charge current too high.

056 INT_Comm Fail Communication error with lithium batteries.

057 EXT_Comm Fail Communication error with inverter charger.

058 SOC_Low Lithium battery’s SOC is too low

IS515

Issue 1: 16/11/2022

WARRANTY STATEMENT

Applicable only to product sold in Australia

Brown & Watson International Pty Ltd of 1500 Ferntree Gully Road, Knoxfield, Vic., telephone (03) 9730 6000,

fax (03) 9730 6050, warrants that all products described in its current catalogue (save and except for all

bulbs and lenses whether made of glass or some other substance) will under normal use and service be free

of failures in material and workmanship for a period of two (2) year (unless this period has been extended

as indicated elsewhere) from the date of the original purchase by the consumer as marked on the invoice.

This warranty does not cover ordinary wear and tear, abuse, alteration of products or damage caused by the

consumer.

To make a warranty claim the consumer must deliver the product at their cost to the original place

of purchase or to any other place which may be nominated by either BWI or the retailer from where

the product was bought in order that a warranty assessment may be performed. The consumer must

also deliver the original invoice evidencing the date and place of purchase together with an explanation

in writing as to the nature of the claim.

In the event that the claim is determined to be for a minor failure of the product then BWI reserves the

right to repair or replace it at its discretion. In the event that a major failure is determined the consumer

will be entitled to a replacement or a refund as well as compensation for any other reasonably foreseeable

loss or damage.

This warranty is in addition to any other rights or remedies that the consumer may have under State or

Federal legislation.

IMPORTANT NOTE

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure.

Distributed by

AUSTRALIA

Brown & Watson International Pty. Ltd.

Knoxfield Victoria 3180

Phone: (03) 9730 6000

Fax: (03) 9730 6050

National Toll Free: 1800 113 443

NEW ZEALAND OFFICE

Griffiths Equipment Ltd.

19 Bell Avenue,

Mount Wellington,

Auckland 1060, New Zealand

Phone: (09) 525 4575 Fax: (09) 579 1192

SPECIFICATIONS

DISPLAY DESCRIPTION

Input Voltage 6.5~16Vdc

Communication RS485

Cable Length 5 metres

IP Rating IP20

Working Temperature -20~65°C

Suits Inverters INVCHR2, INVCHR3 & INVCHR3-48V

Suits Batteries in system LB100-HD, LB200HD, LB400-HD, LB50-48VHD, LB100-48HD

Inhaltsverzeichnis

Andere Projecta Akkuladegerät Handbücher

Projecta

Projecta IM120 Bedienungsanleitung

Projecta

Projecta INTELLI JAY PM100-BTJ Bedienungsanleitung

Projecta

Projecta INTELLI-CHARGE IC7 Bedienungsanleitung

Projecta

Projecta AC150 Bedienungsanleitung

Projecta

Projecta INVCHR2 Bedienungsanleitung

Projecta

Projecta HDBC90 Bedienungsanleitung

Projecta

Projecta IC100L Bedienungsanleitung

Projecta

Projecta IC1500L Bedienungsanleitung

Projecta

Projecta Charge N' Maintain Bedienungsanleitung

Projecta

Projecta HDBM4000 Bedienungsanleitung

Projecta

Projecta INTELLI-CHARGE DC/SOLAR BATTERY CHARGER... Bedienungsanleitung

Projecta

Projecta PMDCS30 Bedienungsanleitung

Projecta

Projecta AC040 Bedienungsanleitung

Projecta

Projecta IDC45 Bedienungsanleitung

Projecta

Projecta IC2500 Bedienungsanleitung

Projecta

Projecta INTELLI-RV PM300 Bedienungsanleitung

Projecta

Projecta HDBC45 Bedienungsanleitung

Projecta

Projecta INTELLI-RV PM200 Bedienungsanleitung

Projecta

Projecta INTELLI-CHARGE IC25 Bedienungsanleitung

Projecta

Projecta IDC25X Bedienungsanleitung

Projecta

Projecta HDBC20 Bedienungsanleitung

Projecta

Projecta IC2500L Bedienungsanleitung

Projecta

Projecta IDC25 Bedienungsanleitung

Projecta

Projecta IC700 Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung