ProLights EclPanel TWC Bedienungsanleitung
USER MANUAL
REV.04-11/20 English version
EclPanel TWC
740W Tunable White and
Colourful LED soft light with pixels
and lighting effects
Thank you for choosing PROLIGHTS.
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance require-
ments for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respec-
tively applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any
other loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS
services or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and sub-
sidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via Appia km
136,200; Itri 04020, Italy.
01
PROLIGHTS - Ecl PanelTWC
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
OPTIONAL ACCESSORIES............................................................................................. 05
2 - TECHNICAL DRAWING 06
3 - INSTALLATION 07
MOUNTING.................................................................................................................... 07
4 - CONNECTION TO THE MAINS SUPPLY 08
5 - START UP 08
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 08
6 - PRODUCT OVERVIEW 09
7 - DMX CONNECTION 10
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 10
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 10
CONNECTION DAISY CHAIN........................................................................................ 10
CONNECTION OF THE DMX LINE................................................................................ 10
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 11
DMX ADDRESSING ........................................................................................................ 11
OPERATION AS A WIRELESS TRANSMITTER................................................................ 11
Unlinking the transmitter ................................................................................................ 12
DMX TO WDMX (TX)...................................................................................................... 12
OPERATION AS A WIRELESS RECEIVER........................................................................ 12
Reset the receiver ........................................................................................................... 12
WDMX TO DMX (RX)...................................................................................................... 12
8 - CONTROL PANEL 13
DISPLAY AND BUTTONS LAYOUT................................................................................. 13
ROTATORY KNOB LAYOUT ........................................................................................... 13
9 - MENU STRUCTURE 14
10 - RDM FUNCTIONS 18
11 - DMX CHARTS 19
12 - ACCESSORIES INSTALLATION 27
THE POLE OPERATED YOKE (code ECLPANELPOYO).................................................. 27
RIGID EGG CRATES (codes EPTWCEC4C, EPTWCEC30, EPTWCEC60)....................... 28
DIFFUSION FILTERS (codes EPTWCFILTERHD, EPTWCFILTERMD, EPTWCFILTERLD) . 29
BARN DOOR (code EPTWCBDR2) ................................................................................. 30
13 - MAINTENANCE 31
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 31
REPLACING THE FUSE................................................................................................... 31
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 31
TROUBLESHOOTING..................................................................................................... 32
PROLIGHTS - Ecl PanelTWC02
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, power-
ing, operating or servicing the product and observe the indications also for its future
handling.
This unit is not for household use, only professional applications.
Installation
• This product is designed for indoor and dry environments.
• Do not use in wet location and do not expose the xture to rain or moisture.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture. Damage caused by inadequate cleaning or
maintenance is not covered by the product warranty.
0,5 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0.5 meters (1.64 ft) from the lens of the projector.
T
45°
C
aMax operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
T
-20°
C
a
Minimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).
Protection from burns and fire
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
Indoor use
• This product is designed for indoor and dry environments.
• Do not use in wet location and do not expose the xture to rain or moisture.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture. Damage caused by inadequate cleaning or
maintenance is not covered by the product warranty.
T
50°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 50 °C (122 °F) during operation. Avoid
contact with people and materials.
03
PROLIGHTS - Ecl PanelTWC
Protection and Warning against electrical shock
• Do not remove any cover from the product and disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, cable,
or other component is damaged, defective, deformed or showing signs of overheat-
ing. Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical
installer.
• Use only AC supplies 100-240V 50-60Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
T
70°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 70 °C (159.8 °F) during operation. Avoid
contact with people and materials.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 2 according to EN 62471.
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
10.5 m
34.45 ft
PROLIGHTS - Ecl PanelTWC04
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
• The device should be positioned so that prolonged staring into the luminaire at a
distance closer than 10.5 m is not expected.
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU - Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-
pose/recycle this product at the end of its life according to the local regulation.
• The product contains a lithium ion battery.
• Don't throw the unit into the garbage at the end of its lifetime.
• Make sure to dispose is according to your local ordinances and/or regulations, to
avoid polluting the environment!
• The packaging is recyclable and can be disposed.
The products to which this manual refers comply with the European Directives pur-
suant to:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).
• 2014/30/EU - Electromagnetic Compatibility (EMC).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
• 2014/53/EU - Radio Equipment Directive (RED).
05
PROLIGHTS - Ecl PanelTWC
1 - PACKAGING
PACKAGE CONTENT
• 1x ECLPANELTWC;
• 1x 1,5 meters SCHUKO - NEUTRIK POWERCON TRUE1 power cable;
• 1x EPTWCFILTERMD: Front medium diffusion lter for ECLPANELTWC;
• 1x ECLFRSPG: Spigot for PROLIGHTS Fresnel series;
• User manual.
OPTIONAL ACCESSORIES
• FCLPANEL1U: Flight case for 1 pc of ECLPANELTWC;.
• FCLPANEL3U: Flight case for 3 pcs of ECLPANELTWC;
• ECLPANELPOYO: Pole operated aluminium yoke bracket for ECLPANELTWC;
• EPTWCFILTERINT: Front intensied diffusion lter for ECLPANELTWC;
• EPTWCFILTERHD: Front high diffusion lter (less output) for ECLPANELTWC;
• EPTWCFILTERLD: Front low diffusion lter (more output) for ECLPANELTWC;
• EPTWCEC30: 30 degree egg crate for ECLPANELTWC;
• EPTWCEC60: 60 degree egg crate for ECLPANELTWC;
• EPTWCEC8C: 8 chamber egg crate for ECLPANELTWC;
• EPTWCBDR2: Barn door with 4 directional aps to adjust the light beam;
• EPTWCSB21: SnapBag 2x1 for ECLPANELTWC by DoP choice;
• EPTWCSG4SB2140: 40° SnapGrid for SnapBag, 2x1 for ECLPANELTWC by DoP choice;
• EPTWCSG2140: 40° SnapGrid, 2x1 for ECLPANELTWC by DoP choice;
• EPSRER: Rabbit-Ears 2x1 Rectangular for ECLPANELTWC by DoP choice;
• EPSBRL3: Snapbag Lantern 3' for Rabbit-Ears by DoP. Incl. Lantern, Backcovers, Carry Bag;
• EPSBRL3C4: Cover for Snapbag Lantern 3' (EPSBRL3) by DoP choice; 4 sides, adj. with zipper;
• EPSBRM: SnapBag Medium to be mounted on Rabbit Ears by DoP;
• EPSGCM40: SnapBag Medium to be mounted on Rabbit Ears by DoP;
• EPSBRO3: Snapbag Octa 3' to be mounted on Rabbit-Ears by DoP;
• EPSGC3W40: 40° SnapGrid, to be mounted on Snap Bag Octa 3' (EPSBRO3);
• EPSBRO5: Snapbag Octa 5' to be mounted on Rabbit-Ears by DoP;
• EPSGC5W40: 40° SnapGrid, to be mounted on Snap Bag Octa 5' (EPSBRO5);
• SWIT500W2KIT: 24/48V 500W battery (>1.2hrs) KIT including 2*PBH260S smart power batt.+st.
adapt;
• UPBOX1U: Firmware uploader kit, USB IN, 3pin XLR DMX OUT, USB OUT;
• RSR: Steel security cable for hanging bodies, inox steel shackle;
• C6040: Heavy-load aluminum clamp, 500kg loa, 48-51mm tubes, M10 bolt inc.
PROLIGHTS - Ecl PanelTWC06
2 - TECHNICAL DRAWING
Dimensions are in mm / in - Fig.1
Weight: 15.3 kg - 33.73 lbs
Weight: 17.1kg - 36.70 lbs
07
PROLIGHTS - Ecl PanelTWC
Fig.2
3 - INSTALLATION
MOUNTING
Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,
auxiliary equipment, etc. and complies with locally applicable regulations.
When suspending the xture above ground level, secure it against failure of primary attachments by
attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor
point on the product main frame.
Do not use removable parts or weak anchors for secondary attachment.
Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-
pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
Ø11 [Ø0.4]
Clamp
Steel security cable
PROLIGHTS - Ecl PanelTWC08
5 - START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT
To apply and disconnect power to the product:
• Check that the product is installed and secured as indicated in the Safety Informations, and that
personal safety will not be put at risk when the xture lights up.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is then ready for its operations and can be controlled through the available input sig-
nals on board.
• To disconnect power from the product, disconnect the Mains from the socket.
• In case you wish to run the product through an external battery, then connect the product to an
external battery (24-36V) into the dedicated XLR4p socket; to disconnect power, disconnect the
Battery from the socket.
4 - CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the xture must be earthed!
The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
If you need to install a power plug on the power cable to allow connection to power outlets, install a
grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts
about proper installation, consult a qualied electrician.
T max power consumption is 440W.
Core (EU) Core (US) Connection Plug terminal marking
Brown Black Live L
Blue White Neutral N
Yellow+green Green Earth
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ProLights Beleuchtungsausrüstung Handbücher
ProLights
ProLights BB5PIX Bedienungsanleitung
ProLights
ProLights PINSPOT 101 Bedienungsanleitung
ProLights
ProLights ArcPod 27VW Bedienungsanleitung
ProLights
ProLights DIGIDRIVERIP Bedienungsanleitung
ProLights
ProLights Z390LED Bedienungsanleitung
ProLights
ProLights MOVING HEAD Bedienungsanleitung
ProLights
ProLights LUMIPIX6TRI Bedienungsanleitung
ProLights
ProLights FURY FY250W Bedienungsanleitung
ProLights
ProLights Cromowash300 Bedienungsanleitung
ProLights
ProLights LUMIPAR7QPRO Bedienungsanleitung
ProLights
ProLights DIAMOND31 Bedienungsanleitung
ProLights
ProLights StudioCob PFC2 Bedienungsanleitung
ProLights
ProLights EVO90F Bedienungsanleitung
ProLights
ProLights LUMA 1500SH Bedienungsanleitung
ProLights
ProLights ArcPod 15VW Bedienungsanleitung
ProLights
ProLights HZ900D Bedienungsanleitung
ProLights
ProLights LEDFLOWERKIT4 Bedienungsanleitung
ProLights
ProLights Fury FY400S Bedienungsanleitung
ProLights
ProLights SLASH Bedienungsanleitung
ProLights
ProLights NEWMOON Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
