ProLights StudioCob PFC2 Bedienungsanleitung

USER MANUAL

English version

StudioCob PFC2

150W IP65 rated full colour COB LED Par

REV.01-09/21

Thank you for choosing PROLIGHTS

Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements

for professionals and designed and manufactured for the use and application as shown in this document.

Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be

a source of danger.

This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively

applicable national accident prevention rules and regulations.

Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated

companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other

loss occasioned by the use of, inability to use or reliance on the information contained in this document.

Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial

PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).

Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad

set of always updated technical documentation: specications, user manual, technical drawings, photometrics,

personalities, xture rmware updates.

The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS servicesor

PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.

04026 - Minturno (LT) ITALY.

Visit the download area

of the product page

PROLIGHTS - StudioCob PFC2 01

INDEX

SAFETY INFORMATION 02

1 - PACKAGING 05

PACKAGE CONTENT..................................................................................................... 05

OPTIONAL ACCESSORIES............................................................................................. 05

2 - TECHNICAL DRAWING 05

3 - INSTALLATION 06

MOUNTING.................................................................................................................... 06

4 - CONNECTION TO THE MAINS SUPPLY 07

5 - START UP 07

CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 07

6 - PRODUCT OVERVIEW 08

7 - DMX CONNECTION 09

CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 09

INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 09

CONNECTION DAISY CHAIN........................................................................................ 09

CONNECTION OF THE DMX LINE................................................................................ 09

CONSTRUCTION OF THE DMX TERMINATION ........................................................... 10

DMX ADDRESSING ........................................................................................................ 10

8 - CONTROL PANEL 11

DISPLAY AND BUTTONS LAYOUT................................................................................. 11

9 - MENU STRUCTURE 12

10 - RDM FUNCTIONS 14

11 - DMX CHARTS 15

12 - ACCESSORIES INSTALLATION 17

FILTER FRAME (CODE STUDIOCOBTPG - OPTIONAL)................................................. 17

BARN DOOR (CODE STUDIOCOBBD - OPTIONAL)..................................................... 18

OPTIC (CODE STUDIOCOBPLUSL18/30/60 - OPTIONAL)............................................ 19

13 - MAINTENANCE 20

MAINTENANCE AND CLEANING THE PRODUCT........................................................ 20

VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 20

TROUBLESHOOTING..................................................................................................... 21

PROLIGHTS - StudioCob PFC2

SAFETY INFORMATION

WARNING!

• Please read carefully the instruction reported in this section before installing, power-

ing, operating or servicing the product and observe the indications also for its future

handling.

This unit is not for household use, only professional applications.

Connection to mains supply

• The Connection to the mains supply must be carried out by a qualied electrical installer.

• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected

to ground (earth).

• Select the cable cross section in according with the maximum current draw of the

product and the possible number of products connected at the same power line.

• The AC mains power distribution circuit must be equipped with magnetic+residual

current circuit breaker protection.

• Do not connect it to a dimmer system; doing so may damage the product.

Protection and Warning against electrical shock

• Do not remove any cover from the product, always disconnect the product from AC

power before servicing.

• Ensure that the xture is electrically connected to ground (earth). And use only a

source of AC power that complies with local building and electrical codes and has

both overload and ground-fault (earth-fault) protection.

• Before using the xture, check that all power distribution equipment and cables are

in perfect condition and rated for the current requirements of all connected devices.

• Isolate the xture from power immediately if the power plug or any seal, cover, cable, or

other components are damaged, defective, deformed or showing signs of overheating.

• Do not reapply power until repairs have been completed.

• Refer any service operation not described in this manual to PROLIGHTS Service team

or an authorized PROLIGHTS service center.

Installation

• Make sure that all visible parts of the product are in good visible condition before its

use or installation.

• Make sure the point of anchorage is stable before positioning the projector.

• When suspending the xture above ground level, secure it against failure of primary

attachments by attaching a safety cable that is approved as a safety attachment for

the weight of the xture to the attachment point on the main frame of the product. ln

case the safety cable, enter in action, it needs to be replaced with a new one.

• Install the product only in well ventilated places.

• For non temporary installations, ensure that the xture is securely fastened to a load-

bearing surface with suitable corrosionresistant hardware.

• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or

screws are turned fully, and secured with a suitable safety cable.

0,5 m Minimum distance of illuminated objects

• The projector needs to be positioned so that the objects hit by the beam of light are

at least 0.5 meters (1.64 ft) from the lens of the projector.

45°

Max operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).

PROLIGHTS - StudioCob PFC2 03

-20°

aMinimum operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).

Protection from burns and re

• The exterior of the xture becomes hot during use. Avoid contact by persons and materials.

• Ensure that there is free and unobstructed airow around the xture.

• Keep ammable materials well away from the xture.

• Do not expose the front glass to sunlight or any other strong light source from any an-

gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.

• Do not attempt to bypass thermostatic switches or fuses.

IP65

Outdoor (temporary) use

• This product is rated with an IP (Ingress protection) for temporary outdoor use when

used and serviced according to the instruction contained in this document.

• Never use the xture in places subject to vibrations or bumps.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Excessive dust, smoke uid, and particle build up degrades performance, causes

overheating and will damage the xture.

• Damages caused by inadequate cleaning or maintenance are not covered by the

product warranty.

60°

Temperature of the external surface

• The surface of the xture can reach up to 60 °C (140 °F) during operation. Avoid

contact with people and materials.

Maintenance

• Warning! Disconnect the xture from AC mains power and allow to cool for at least

10 minutes before handling.

• Only technicians who are authorized by PROLIGHTS or Authorised service partners

are permitted to open the xture.

• Users may carry out external cleaning, following the warnings and instructions pro-

vided, but any service operation not described in this manual must be referred to a

qualied service technician.

• Important! Excessive dust, smoke uid, and particle build up degrades performance,

causes overheating and will damage the xture. Damages caused by inadequate

cleaning or maintenance is not covered by the product warranty.

Photobiological safety

• This device emits potentially dangerous optical radiation and is identied in the cat-

egory of Risk Group 1 according to EN 62471.

Do not stare at the operating light source

• Do not look directly at the LED source during operation. It can be harmful to the eyes

and skin.

• During Installation, operation and maintenance, be prepared for the xture to light

and move suddenly when connected to power.

Disposal

• This product is supplied in compliance with European Directive 2012/19/EU – Waste

Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-

pose/ recycle this product at the end of its life according to the local regulation.

PROLIGHTS - StudioCob PFC2

The products to which this manual refers comply with:

• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).

• 2014/30/EU - Electromagnetic Compatibility (EMC).

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).

Other approvals

• The product meets the safety requirements of the certification procedures of the

market in which it is placed and sold.

PROLIGHTS - StudioCob PFC2 05

1 - PACKAGING

PACKAGE CONTENT

• STUDIOCOBPFC2;

• 1x 1,5 meters power cable (SCHUKO plug - SEETRONIC IP65 power connector);

• User manual.

OPTIONAL ACCESSORIES

• INF53415L03: dmx cable HC5340. SETMC5MXXB XLR 5p->SETMC5FXXB XLR (f) 5p;

• 938225L03: 3x2.5mm TH07 Cable, 16A SETSAC3MX, 16A SETSAC3FX, L. 3m;

• 9313FXWL03: ass. 3x2.5mm TH07 cable, 16A 3p 230V CEE plug, SETSAC3FX socket, L.3 m;

• 9333FXWL03: ass. 3x2.5mm TH07 cable, SHUKO plug, SETSAC3FX socket, L.3m;

• C6002: slim aluminium clamp, 200 kg loading, 48-51 mm tubes, M10 bolt;

• RSR0630A/B: steel security cable for hanging bodies, inox steel shackle, L=60 cm, silver/black;

• STUDIOCOBPLUSL18: optics for STUDIOCOBPLUS projectors series, 18°;

• STUDIOCOBPLUSL38: optics for STUDIOCOBLUS projectors series, 38°;

• STUDIOCOBPLUSL60: optics for STUDIOCOBLUS projectors series, 60°;

• STUDIOCOBTPG: lter frame for STUDIOCOB projectors;

• STUDIOCOBBD: barn door 4 directional aps to adjust the light beam, f. frame included;

• FCLCOBPLUS: ight case for 8 STUDIOCOBPLUS;

• UPBOX1U: rmware uploader kit, USB IN, 3p XLR DMX OUT.

2 - TECHNICAL DRAWING

Fig. 01Weight: 5.6 kg - 12.34 lbs

PROLIGHTS - StudioCob PFC2

Fig. 02

3 - INSTALLATION

MOUNTING

Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,

auxiliary equipment, etc. and complies with locally applicable regulations.

When suspending the xture above ground level, secure it against failure of primary attachments by

attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor

point on the product main frame.

Do not use removable parts or weak anchors for secondary attachment.

Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-

pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.

215 mm

8.5 in

Ø13 mm

Ø0.5 in

45 mm

1.8 in

RSR0630A/B

steel security cable

C6002

clamp

PROLIGHTS - StudioCob PFC2 07

5 - START UP

CONNECT AND DISCONNECT POWER FROM THE PRODUCT

To apply and disconnect power to the product:

• Check that the product is installed and secured as indicated in the Safety Informations, and that

personal safety will not be put at risk when the xture lights up.

• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).

• The product is then ready for its operations and can be controlled through the available input sig-

nals on board.

• To disconnect power from the product, disconnect the Mains from the socket.

4 - CONNECTION TO THE MAINS SUPPLY

WARNING: For protection from electric shock, the xture must be earthed!

The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz

AC power source from 100-240 Volts.

If you need to install a power plug on the power cable to allow connection to power outlets, install a

grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts

about proper installation, consult a qualied electrician.

The max power consumption is 140W.

Core (EU) Core (US) Connection Plug terminal marking

Brown Black Live L

Blue White Neutral N

Yellow+green Green Earth

PROLIGHTS - StudioCob PFC2

36 5 489

6 - PRODUCT OVERVIEW

1. BRACKET;

2. SAFETY EYE to attach safety cable;

3. KNOB for bracket;

4. DMX IN (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C;

5. POWER IN: for connection to the Mains 100-240V~/50-60Hz;

6. USER INTERFACE with display and buttons for access to the control panel functions.

7. DMX OUT (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C;

8. POWER OUT: power output for connection of multiple units in series;

9. GORE VALVE.

Fig. 03

Inhaltsverzeichnis

Andere ProLights Beleuchtungsausrüstung Handbücher

ProLights

ProLights EclMini CC Bedienungsanleitung

ProLights

ProLights 201119080 Bedienungsanleitung

ProLights

ProLights PIXBAR3E Bedienungsanleitung

ProLights

ProLights ArcPod 15VW Bedienungsanleitung

ProLights

ProLights EclPanel TWCXL Bedienungsanleitung

ProLights

ProLights EclProfile FW Bedienungsanleitung

ProLights

ProLights FURY FY250W Bedienungsanleitung

ProLights

ProLights PANORAMA IP AIRBEAM Bedienungsanleitung

ProLights

ProLights Titan Bedienungsanleitung

ProLights

ProLights FS75LED Bedienungsanleitung

ProLights

ProLights EclPanel TWC Bedienungsanleitung

ProLights

ProLights ECLIPSEJZIP Bedienungsanleitung

ProLights

ProLights CUBER128 Bedienungsanleitung

ProLights

ProLights Diamond142L Bedienungsanleitung

ProLights

ProLights LUMIPAR7QTOUR Bedienungsanleitung

ProLights

ProLights EclCyclorama 050 Bedienungsanleitung

ProLights

ProLights EclProfile FW IPVW Bedienungsanleitung

ProLights

ProLights DIAMOND19TW Bedienungsanleitung

ProLights

ProLights ArcPod 27VW Bedienungsanleitung

ProLights

ProLights Astra Wash37Pix Bedienungsanleitung

ProLights

ProLights Mosaico L Bedienungsanleitung

ProLights

ProLights LUMIPIX6TRI Bedienungsanleitung

ProLights

ProLights Astra Profile600IP Bedienungsanleitung

ProLights

ProLights EclNanoPanel TWC Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung