ProLights EclProfile FW IP Bedienungsanleitung
USER MANUAL
REV.01-02/22 English version
EclProfile FW IP
High quality Full White LED ellipsoidal
available in Tungsten and Daylight
versions
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS servicesor
PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
Visit the download area
of the product page
PROLIGHTS - EclProfile FW IP 01
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
OPTIONAL ACCESSORIES............................................................................................. 05
2 - TECHNICAL DRAWING 06
3 - INSTALLATION 09
MOUNTING.................................................................................................................... 09
4 - CONNECTION TO THE MAINS SUPPLY 10
5 - START UP 10
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 10
6 - PRODUCT OVERVIEW 11
7 - DMX CONNECTION 12
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 12
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 12
CONNECTION DAISY CHAIN........................................................................................ 12
CONNECTION OF THE DMX LINE................................................................................ 12
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 13
DMX ADDRESSING ........................................................................................................ 13
8 - CONTROL PANEL 14
DISPLAY AND BUTTONS LAYOUT................................................................................. 14
9 - MENU STRUCTURE 15
10 - RDM FUNCTIONS 17
11 - SHORTCUTS 18
12 - ERROR MESSAGES 18
13 - DMX CHARTS 19
13 - ACCESSORIES INSTALLATION 24
OPTIC (CODE ECLPRL - OPTIONAL) ............................................................................. 24
GEL FILTER FRAME (CODE ECLPRTPG - OPTIONAL) ................................................... 25
GOBO HOLDER (CODE ECLPRGH - OPTIONAL).......................................................... 26
STEEL IRIS DIAPHRAM (CODE ECLPRIRIS - OPTIONAL)............................................... 28
SOFT EDGE FILTER (CODE ECLPRSEF1 - OPTIONAL).................................................. 29
SOFT FOCUS DIFFUSION (CODE ECLPRSMOOTHF1 - OPTIONAL)............................ 30
POLE OPERATED YOKE (CODE ECLPRPOYO - OPTIONAL)......................................... 31
ROTATING GOBO ASSEMBLY (CODE ECLPRIPROTGOBO1 - OPTIONAL).................. 32
14 - TEST OF IP65 RATING 33
15 - MAINTENANCE 34
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 34
REPLACING THE FUSE................................................................................................... 34
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 34
TROUBLESHOOTING..................................................................................................... 35
PROLIGHTS - EclProfile FW IP
02
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, power-
ing, operating or servicing the product and observe the indications also for its future
handling.
This unit is not for household and residential use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical
installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, ca-
ble, or other components are damaged, defective, deformed or showing signs of
overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
0,3 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0.3 meters (0.98 ft) from the lens of the projector.
PROLIGHTS - EclProfile FW IP 03
T
45°
C
a
Max operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
T
-15°
C
a
Minimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -15 °C (5 °F).
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
IP65
Outdoor (temporary) use
• This product is rated with an IP (Ingress protection) for temporary outdoor use when
used and serviced according to the instruction contained in this document.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty
T
58°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 58 °C (136.4 °F) during operation. Avoid
contact with people and materials.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 2 according to EN 62471.
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
• The device should be positioned so that prolonged staring into the luminaire at a
distance closer than 3.30 m is not expected.
PROLIGHTS - EclProfile FW IP
04
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
3.30 m
10.83 ft
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-
pose/ recycle this product at the end of its life according to the local regulation.
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).
• 2014/30/EU - Electromagnetic Compatibility (EMC).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
The products to which this manual refers comply with:
• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.
• UL 1012 + CSA C22.2 No. 107.1 - Standard for power units other than class 2.
FCC Compliance:
• This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Other approvals
• The product meets the safety requirements of the certification procedures of the
market in which it is placed and sold.
PROLIGHTS - EclProfile FW IP 05
1 - PACKAGING
PACKAGE CONTENT
• 1 x ECLFWIPDY/TU;
• 1x 1,5 meters power cable (BARE END - SEETRONIC IP65 power connector);
• User manual.
OPTIONAL ACCESSORIES
• INF53415L03: dmx cable HC5340. SETMC5MXXB XLR 5p->SETMC5FXXB XLR (f) 5p;
• 9333FXWL03: ass. 3x2.5mm TH07 cable, SHUKO plug, SETSAC3FX socket, L.3m
• 9313FXWL03: ass. 3x2.5mm TH07 cable, 16A 3p 230V CEE plug, SETSAC3FX socket, L.3 m;
• 938225L03: 3x2.5mm TH07 Cable, 16A SETSAC3MX, 16A SETSAC3FX, L. 3m;
• RSR0630A/B: steel security cable for hanging bodies, inox steel shackle, L=60 cm, silver/black;
• C6040: heavy-load aluminum clamp, 200kg load, 48-51mm tubes, M10 bolt inc;
• C6002: slim aluminium clamp, 200 kg loading, 48-51 mm tubes, M10 bolt;
• FCLECLPRIP: ightcase to contain 8 pcs ECLFWIP / ECLCTPLUS with lenses 19°, 26°, 36°, 50°;
• FCLECLPRLZ: ightcase to contain 8 ECLPRLZ zoom lenses;
• ECLPRL05BK: 5° PRL lens barrel for EclProle xtures, black housing;
• ECLPRL10BK: 10° PRL lens barrel for EclProle xtures, black housing;
• ECLPRL14BK: 14° PRL lens barrel for EclProle xtures, black housing;
• ECLPRL19BK: 19° PRL lens barrel for EclProle xtures, black housing;
• ECLPRL26BK: 26° PRL lens barrel for EclProle xtures, black housing;
• ECLPRL36BK: 36° PRL lens barrel for EclProle xtures, black housing;
• ECLPRL50BK: 50° PRL lens barrel for EclProle xtures, black housing;
• ECLPRL70BK: 70° PRL lens barrel for EclProle xtures, black housing;
• ECLPRLZ1530BK: zoom 15°-30° PRL lens barrel for EclProle xtures, black housing;
• ECLPRLZ2550BK: zoom 25°-50° PRL lens barrel for EclProle xtures, black housing;
• ECLPRTPG: gel lter frame for ECL Prole PRL lens barrel, comp. with 19°,26°,36° and 50°;
• ECLPRGH: gobo holder for ECL Prole xtures;
• ECLPRIRIS: iris accessory for ECL Prole xtures;
• ECLPRSEF1: soft edge lter and holder kit for ECL Prole xtures;
• ECLLZLLKA: hexagonal head screw, to adapt and mount ECLLZ lenses on ECLCTPLUS and ECLFS;
• ECLPRSMOOTHF1: smooth/homogenizer lter with aluminium frame and magnets for Ecl Prole xture;
• ECLPRPOYO: pole operated aluminium yoke bracket for ECLCTPLUS and ECLFS;
• ECLPRIPROTGOBO1BK/WH: rotating gobo assembly for ECL Prole xtures, black/white;
• IPTESTBOX: portable vacuum and pressure tester for ProLights IP xtures;
• SPGM12: 28mm spigot for xtures, M12 bolt;
• SPGM10: 28mm spigot for xtures, M10 bolt;
• UPBOX2P5: rmware uploader kit, USB IN, 5-pin XLR DMX OUT.
PROLIGHTS - EclProfile FW IP
06
2 - TECHNICAL DRAWING
Weight: 7.3 kg - 16.09 lbs ECLFWIP without optic
Weight: 10.2 kg - 22.48 lbs ECLFWIP with ECLPRL05
Weight: 9.2 kg - 20.28 lbs ECLFWIP with ECLPRL10
PROLIGHTS - EclProfile FW IP 07
Weight: 10.6 kg - 23.37 lbs ECLFWIP with ECLPRL14
Weight: ECLPRL19: 9.5 kg - 20.94 lbs
Weight: ECLPRL26: 9.7 kg - 21.38 lbs
Weight: ECLPRL36: 9.4 kg - 20.72 lbs
Weight: ECLPRL50: 9 kg - 19.84 lbs
ECLFWIP with ECLPRL19
ECLFWIP with ECLPRL26
ECLFWIP with ECLPRL36
ECLFWIP with ECLPRL50
Weight: 9.1 kg - 20.06 lbs ECLFWIP with ECLPRL70
PROLIGHTS - EclProfile FW IP
08
Weight: 11.3 kg - 24.91 lbs ECLFWIP with ECLPRLZ1530
Weight: 11.3 kg - 24.91 bs ECLFWIP with ECLPRLZ2550
Fig. 01
Inhaltsverzeichnis
Andere ProLights Beleuchtungsausrüstung Handbücher
ProLights
ProLights EclProfile FW IPVW Bedienungsanleitung
ProLights
ProLights PFZ725 Bedienungsanleitung
ProLights
ProLights LUMIPAR12IRTRI Bedienungsanleitung
ProLights
ProLights DIAMOND19TW Bedienungsanleitung
ProLights
ProLights LUMIPAR18QTOUR Bedienungsanleitung
ProLights
ProLights DIAMOND19CC Bedienungsanleitung
ProLights
ProLights EclProfile FW Bedienungsanleitung
ProLights
ProLights UPBOX2 Bedienungsanleitung
ProLights
ProLights ArcPod 48Q Bedienungsanleitung
ProLights
ProLights LUXOR Bedienungsanleitung
ProLights
ProLights Cromowash300 Bedienungsanleitung
ProLights
ProLights ARCLED5118 Bedienungsanleitung
ProLights
ProLights EclMiniProfile WDMX Bedienungsanleitung
ProLights
ProLights EclFresnel TW Bedienungsanleitung
ProLights
ProLights Diamond 193 Bedienungsanleitung
ProLights
ProLights ELFIN FC Bedienungsanleitung
ProLights
ProLights PINSPOT 101 Bedienungsanleitung
ProLights
ProLights PIXIE BEAM Bedienungsanleitung
ProLights
ProLights EVO128CYC Bedienungsanleitung
ProLights
ProLights LUMIPIX Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
