5
TECHNICAL PARAMETERS: which the laser device is standing is more than 3° from level, the laser
level should be adjusted horizontally using a tripod or universal bracket
(2).
źTo turn on the device with a locked pendulum (closed padlock symbol
) in order to set oblique lines, press the button (14) and hold it for 5
seconds. In the blocked state the compensator pendulum is
immobilised, which makes self-levelling impossible. The laser beams
will flash every 7 seconds.
źTo turn off the device - move the switch locking the compensator
pendulum to the right (closed padlock symbol ) or, when the device
was turned on with the pendulum blocked, press the button (14) and
hold it for 5 seconds.
nControl panel – description of functions
The laser is quick and easy to use, allowing 360° laser planes to be
displayed - one horizontal and one vertical. Turning surfaces on and off is
done through the laser plane display switch (13) and is performed in the
relevant sequence:
– when the device is turned on, only the horizontal plane is shown;
– after the button (13) is pressed, only the vertical laser beam will be
shown;
PREPARATION FOR WORK: – pressing the button twice will cause both beams, the horizontal and the
Before each use, make sure to check the level for any damage (e.g. vertical, to be shown;
whether its housing is not cracked or its elements are not broken). If any
damage is found, take the device to a service centre to check that it is safe – pressing the button three times will turn off the laser planes.
to use. nLaser brightness reduction function
The laser brightness reduction function is useful for saving batteries.
OPERATING THE DEVICE:
The function is available in the auto-levelling mode. To enable energy
nInstalling and recharging the battery
saving, press the button (14). To turn off energy saving, press the button
Use only the supplied lithium-ion battery to power the level.
(14) again.
To install the battery, open the battery bay cover (11). Insert the battery
(15) into the bay, paying attention to the correct polarity (see Fig. C). Then TIPS FOR WORKING:
close the cover.
źProtect the level from moisture and direct solar radiation.
The level is supplied with a partially charged battery. Charge the battery
źProtect the level from extremely high or low temperatures, as well as
completely before use. To do this, connect the adapter (1) using the USB temperature fluctuations. For example, do not leave the device for a
cable to the charging connector (12) and insert the adapter into a 100-
long time in a car. If the device has been exposed to high temperature
240 V, 50-60 Hz mains socket. A red light on the adapter will turn on,
fluctuations, allow it to return to normal temperature before use.
indicating that charging is in progress. When the battery is fully charged,
the light on the adapter will turn green. źAvoid strong impacts or dropping the spirit level. A damaged laser
If the device is not used for a long time, remove the battery. It may corrode device can make inaccurate measurements. Therefore, after each
or become unusable after a longer break in use. strong impact or drop of the device, the laser line should be compared
The battery should be recharged when the laser light becomes faint and with a previously determined horizontal or vertical reference line.
the laser beam dispersed. źA tripod is recommended to ensure correct operation of the device
n Switching the level on/off (stable surface). Adjust the tripod before switching on the measuring
źTo turn on the device in the auto-levelling mode, move the blocking device.
switch of the compensator pendulum (8) to the left (open padlock
nWorking with the laser target plate
symbol ) (see Fig. B). After the instrument is switched on, it generates
a horizontal plane, is automatically levelled and compensates for
unevenness within a self-levelling range of ±3° in 5 seconds. If the
device is within its self-levelling limits, the beam will be on The mirror half of the target plate (4) increases the visibility of the laser's
continuously. If the laser beam disappears, the device should be lines.
levelled. When the laser lines stop moving, the levelling has been
nMounting with the universal bracket
completed.
The universal bracket (2) makes it possible to attach the measuring device
If the level is shaken or its working position changes, it automatically
to vertical planes, pipes or magnetic materials.
performs self-levelling again.
If automated self-levelling is not possible, e.g. when the surface on Adjust the universal bracket (2) before turning on the measuring device.
The target plate for the laser (4) increases the visibility of the laser beam
under adverse conditions or at a large distance.
Laser output power P ≤1 mW
Laser wavelength λ 630-640 nm
Laser beam Red, class 2 laser
Accuracy
Typical self-levelling range ±3°
Typical levelling time <5 s
Working range (indoors) up to 20 m (recommended up to 10 m)
Storage temperature o o
+5 C... +45 C
o o
Working temperature +10 C ... +40 C
Max. relative air humidity 90 %
Equipment class III
Device power (battery type) 3,7V 2800mAh Li-ion
Weight 0,626 kg
1 x horizontal (360°),
1 x vertical (360°)
Generated planes
Resistance class IP54
±1.5 mm/5m, ±3 mm/10m
