ProMinent DiaLog DACb Verdrahtungsschema

DULCOMETER®

Multi-parameter Controller diaLog DACb

Supplementary instructions: PROFINET®

A2666

Target group: trained electronics technicians982194 Version: BA DM 228 08/18 EN

Please carefully read these operating instructions before use. · Do not discard.

The operator shall be liable for any damage caused by installation or operating errors.

The latest version of the operating instructions are available on our homepage.

In order to make it easier to read, this document uses the male

form in grammatical structures but with an implied neutral sense. It

is aimed equally at both men and women. We kindly ask female

readers for their understanding in this simplification of the text.

Please read the supplementary information in its entirety.

Information

This provides important information relating to the

correct operation of the unit or is intended to make

your work easier.

Warning information

Warning information include detailed descriptions of the hazardous

situation.

The following symbols are used to highlight instructions, links, lists,

results and other elements in this document:

Tab. 1: More symbols

Symbol Description

Action, step by step.

⇨Outcome of an action.

Links to elements or sections of these instructions or other applicable documents.

nList without set order.

[Button]

Display element (e.g. indicators).

Operating element (e.g. button, switch).

‘Display /GUI’

Screen elements (e.g. buttons, assignment of function keys).

CODE Presentation of software elements and/or texts.

General non-discriminatory approach

Supplementary information

Supplemental directives

Table of contents

1Supplementary Instructions for PROFINET®........................ 4

1.1 Prerequisites................................................................. 4

1.2 Terminal diagram for the DAC communication unit...... 4

1.3 Adjusting the Controller................................................ 4

1.3.1 General...................................................................... 4

1.3.2 Configuring PROFINET®........................................... 4

1.4 Special Features in Active PROFINET® Mode............. 6

1.4.1 General...................................................................... 6

1.4.2 Display....................................................................... 6

1.4.3 LEDs on the PROFINET® DP module....................... 6

1.5 Installation..................................................................... 7

1.6 Operation...................................................................... 7

1.6.1 General...................................................................... 7

1.6.2 GSDML file................................................................ 7

1.6.3 Description of the DACa data objects........................ 8

1.7 Bit field definitions....................................................... 14

1.7.1 Status of the channel............................................... 14

1.7.2 Error of the channel................................................. 16

1.7.3 Warning of the channel............................................ 17

1.7.4 Potential-free relay................................................... 18

1.7.5 Settings of the channel configuration....................... 19

1.8 Diagnostic messages.................................................. 20

1.9 PLC Programmable Logic Controller error message

and controller behaviour............................................. 20

Table of contents

1 Supplementary Instructions for PROFINET®

1.1 Prerequisites

Personnel must be familiar with the contents of the "Assembly and

Operating Instructions for DULCOMETER® Multi-parameter Con‐

troller diaLog DACa".

The controller must have a PROFINET® module.

These supplementary instructions are only valid when used in con‐

junction with the operating instructions for the Multi-parameter

Controller diaLog DACb.

1.2 Terminal diagram for the DAC communication unit

A1173

Communication Communication

external connector

Socket M12x1 female

4-pin (D-coded)

green (A)

red (B)

green (A)

red (B)

external

communication

Plug M8x1

ext. connector

2x socket M12x1

Female 4-pin

(D-coded)

Switch

alternative

ext. WLAN router

e.g. TP link

TL-WR702N

Communication

2 x plugs

M8x1 (male)

Fig. 1: Terminal diagram for the DAC communication unit (module

B, optional)

1. Connect the PROFINET® to the DAC communication unit,

Fig. 1.

2. Slot 1 is the left-hand

[IN]

connector.

3. Slot 2 is the right-hand

[OUT]

connector.

1.3 Adjusting the Controller

1.3.1 General

The controller with PROFINET® functionality is adjusted in the

same way as the standard controller, with the addition of the bus

functionality.

Adjustment process cancelled

The adjustment process is cancelled in the event

of a pause longer than 60 seconds.

1.3.2 Configuring PROFINET®

Remote configuration needs to be enabled to be able to configure

and control the controller via the PROFINET®. The PROFINET® is

always enabled but it does not accept external commands if

remote configuration has not been enabled.

Validity of the supplementary instruc‐

tions

Supplementary Instructions for PROFINET®

All external inputs also work while the PROFINET® is enabled. The

external inputs lead to the expected reactions, as in the case of a

controller without PROFINET® functionality (see controller oper‐

ating instructions). The controller sends corresponding information

via the PROFINET® to the master (PLC Programmable Logic Con‐

troller, PC etc.).

Even if the remote configuration is set to inactive, the master is

able to read-access the controller data defined in the GSDML file.

If the remote configuration is inactive or switched to inactive, then

the settings for the operating mode selected prior to "inactive"

status are reloaded in the controller.

If the controller is switched to another operating mode, it stops and

can only be restarted using the

[Stop/Start]

key.

1. To access the

‘Menu’

: press the

[Menu]

key

2. Use the arrow keys to select the menu item

‘Setup’

and con‐

firm with

[OK]

ðThe

‘Device setup’

menu appears.

3. Use the arrow keys to select the menu item

‘Bus

configuration’

and confirm with

[OK]

ðThe

‘Configuration’

menu appears.

4. In the

‘Configuration’

menu, you can:

‘Remote configuration’

– Switch remote configuration on or off.

nDHCP

– Switch DHCP on or off.

‘IP address’

– You can set the IP address here at which the con‐

troller can be accessed.

‘Subnet’

– You can set the address of the subnet here.

‘Gateway’

– You can set the address of the gateway here.

‘DNS’

– You can set the address of the DNS here.

‘Station name’

– You can set the station name as an actual word e.g.

"daca" or "daisy", using lower case letters only.

Origin of the designations

The different names and/or addresses represent

user-specific information and are the responsibility

of the system operator.

Supplementary Instructions for PROFINET®

1.4 Special Features in Active PROFINET® Mode

1.4.1 General

Setting or programming

In PROFINET® mode, the controller cannot be

manually set or programmed. Switch off remote

configuration to set or program the controller.

nThe settings from the last operating mode without PROFINET®

are carried over when switching to PROFINET® mode. By con‐

trast, the settings made via the PROFINET® are not saved.

They only apply as long as the controller is linked to the PRO‐

FINET®.

nThe controller stops if it is set to PROFINET® mode. The con‐

troller can be controlled again by pressing the

[Stop/Start]

key. The start command is given via the PROFINET®.

1.4.2 Display

When PROFINET® mode is running there are further identifiers in

the operating indicator.

Common identifiers

The common identifiers are described in the con‐

troller operating instructions.

1.4.3 LEDs on the PROFINET® DP module

Signal Cause

Off The module has no supply voltage or connection.

Green The module and the master are exchanging information.

Green flashing The module has been initialised.

Signal Cause

Off The module has not been initialised.

Green The module has been initialised/normal mode

Green flashing, single flash The module has been initialised and there are diagnostic mes‐

sages.

Green flashing, 1 Hz DCP flash

Red Serious exception error

Red, single flash Configuration error

Red, double flash IP address error

LED 1 (left) - module operating status

LED 2 (right) - module status

Supplementary Instructions for PROFINET®

Signal Cause

Red, triple flash Station name error

Red, quadruple flash Internal error

1.5 Installation

CAUTION!

Degree of protection IP 67

– IP 67 degree of protection only applies if the

appropriate assembly accessories (cable pas‐

sages etc.) have been correctly installed (see

controller assembly and operating instructions).

The connection to the existing LAN infrastructure is provided by a

suitable LAN cable, e.g. twisted pair cable (CAT5 or higher) to

comply with IP 67 with a screwed M12x1 plug, 4-pin, D-coded to

IEC 61076-2-101. Complies with IEEE 802.3.

Mains extension:

nCopper-based twisted pair cable (TP) maximum 100 metres.

A1173

Communication Communication

external connector

Socket M12x1 female

4-pin (D-coded)

green (A)

red (B)

green (A)

red (B)

external

communication

Plug M8x1

ext. connector

2x socket M12x1

Female 4-pin

(D-coded)

Switch

alternative

ext. WLAN router

e.g. TP link

TL-WR702N

Communication

2 x plugs

M8x1 (male)

Fig. 2: Terminal diagram of the communication modules

1.6 Operation

1.6.1 General

When the PROFINET® module is connected, the controller in the

PROFINET® represents a subscriber with slave functionality.

1.6.2 GSDML file

Use the GSDML file to configure the master. The GSDML file

describes all the features of the controller in PROFINET® mode

(keywords, diagnosis, modules, sub-modules). The GSDML file

can be downloaded from the PROFINET® website and from the

ProMinent website. The file name is clearly indicated: GSDML-

V2.32-Prominent-DACa-PRT2P-20150721.xml .

Bus installation

Supplementary Instructions for PROFINET®

1.6.3 Description of the DACa data objects

Tab. 2: Output data

Slot Index Name Module name Data type Byte

count

Total:

Output data

Channel 1

‘Channel 1’

1 2 Measured

value

FLOAT 4

1 3 Controller

control vari‐

able

INT16 2

1 4 Temperature INT16 2 0.1 °C

1 5 Setpoint FLOAT 4

1 6 Channel

status

UINT16 2

Ä Chapter 1.7.1

‘Status of the

channel’

on page 14

1 7 Warnings UINT16 2

Ä Chapter 1.7.3

‘Warning of the

channel’

on page 17

Channel 2

‘Channel 2’

2 2 Measured

value

FLOAT 4

2 3 Controller

control vari‐

able

INT16 2

2 4 Temperature INT16 2 0.1 °C

2 5 Setpoint FLOAT 4

2 6 Channel

status

UINT16 2

Ä Chapter 1.7.1

‘Status of the

channel’

on page 14

2 7 Warnings UINT16 2

Ä Chapter 1.7.3

‘Warning of the

channel’

on page 17

Channel 3

‘Channel 3’

3 2 Measured

value

FLOAT 4

3 3 Controller

control vari‐

able

INT16 2

Supplementary Instructions for PROFINET®

Slot Index Name Module name Data type Byte

count

Total:

3 4 Temperature INT16 2 0.1 °C

3 5 Setpoint FLOAT 4

3 6 Channel

status

UINT16 2

Ä Chapter 1.7.1

‘Status of the

channel’

on page 14

3 7 Warnings UINT16 2

Ä Chapter 1.7.3

‘Warning of the

channel’

on page 17

Channel 4

(differential

channel)

‘Channel 4’

4 1 Measured

value

FLOAT 4

4 2 Channel

status

UINT16 2

Ä Chapter 1.7.1

‘Status of the

channel’

on page 14

4 3 Warnings UINT16 2

Ä Chapter 1.7.3

‘Warning of the

channel’

on page 17

Digital out‐

puts

‘digital output’

5 1 Relay UINT16 2

Ä Chapter 1.7.4

‘Potential-free

relay’

on page 18

5 2 MosFET 1 UINT16 2 Frequency

5 3 MosFET 2 UINT16 2 Frequency

5 4 MosFET 3 UINT16 2 Frequency

5 5 MosFET 4 UINT16 2 Frequency

Error

‘errors’

Supplementary Instructions for PROFINET®

Slot Index Name Module name Data type Byte

count

Total:

6 1 Error

channel 1

UINT32 4

Ä Chapter 1.7.2

‘Error of the

channel’

on page 16

6 2 Error

channel 2

UINT32 4

Ä Chapter 1.7.2

‘Error of the

channel’

on page 16

6 3 Error

channel 3

UINT32 4

Ä Chapter 1.7.2

‘Error of the

channel’

on page 16

6 4 Error

channel 4

UINT16 2

Ä Chapter 1.7.2

‘Error of the

channel’

on page 16

Supplementary Instructions for PROFINET®

Inhaltsverzeichnis

Andere ProMinent Controller Handbücher

ProMinent

ProMinent DULCOMETER D1Cb Bedienungsanleitung

ProMinent

ProMinent DULCOMETER D2C Bedienungsanleitung

ProMinent

ProMinent DCM3 Series Bedienungsanleitung

ProMinent

ProMinent DULCOMETER D2C Bedienungsanleitung

ProMinent

ProMinent PROFIBUS DP DULCOMETER diaLog DACb Verdrahtungsschema

ProMinent

ProMinent DULCOMETER D1C Bedienungsanleitung

ProMinent

ProMinent DULCOMETER D1C Bedienungsanleitung

ProMinent

ProMinent DULCOMETER Bedienungsanleitung

ProMinent

ProMinent DULCOMETER D1C Bedienungsanleitung

ProMinent

ProMinent DCM 5 Series Bedienungsanleitung

ProMinent

ProMinent DULCOMARIN II Verdrahtungsschema

ProMinent

ProMinent DULCOMETER Compact Bedienungsanleitung

ProMinent

ProMinent Aegis-II Bedienungsanleitung

ProMinent

ProMinent DULCOMARIN 3 Compact Bedienungsanleitung

ProMinent

ProMinent DULCOMETER Bedienungsanleitung

ProMinent

ProMinent DULCOMETER D1Cb Bedienerhandbuch

ProMinent

ProMinent DULCOMETER Bedienungsanleitung

ProMinent

ProMinent DULCOMETER Bedienungsanleitung

ProMinent

ProMinent Splash Control Pro 2 Bedienungsanleitung

ProMinent

ProMinent DULCOMETER D1CA Bedienungsanleitung

ProMinent

ProMinent Splash Control 2 Bedienungsanleitung

ProMinent

ProMinent DULCOMETER D1C Bedienungsanleitung

ProMinent

ProMinent DULCOMARIN II DXM Series Verdrahtungsschema

ProMinent

ProMinent DCM510 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

ProMinent diaLog DACb Verdrahtungsschema

Beliebte Controller Handbücher anderer Marken