Prosense PPS Manager Bedienungsanleitung

PRS-UM-PPSM-EN-Rev.03-10.04.2020

PROSENSE PPS Manager Gas Control Panel

User Manual

Prosense Teknoloji San. Ltd. Şti.

Cumhuriyet Mah. Mermer sok. No:16 Kartal İstanbul

Tel: (90) 216 306 77 88 Faks: (90)216 473 81 29

www.prosense.com.tr

PRS-UM-PPSM-EN-Rev.03-10.04.2020

WARNING

This user guide must be carefully read by all persons who are or will have the responsibility for

installing, using or servicing this product. This product must be installed, used and serviced in

accordance with the manufacturer's directives. Otherwise it could fail to perform its functions as

designed and persons who rely on this product for their safety could suffer severe personel injury or

death.

Properly installed panel can be used without any problem and covered under Prosense warranty. The

warranties made by Prosense with respect to this product are voided if the product is not installed,

used and serviced in accordance with the instructions in this user manual.

WARNING

Inductive or capacitive loads like motors,ventilation, eg. should not be directly connected to the

panel directly. In such cases, auxiliary external relays should be use to drive these loads.

PRS-UM-PPSM-EN-Rev.03-10.04.2020

CONTENTS

1.INTRODUCTION .................................................................................................................................... 4

1.1 Technical Specifications............................................................................................................... 4

1.2 Panel Dimensions .............................................................................................................................. 5

2. INSTALLATION..................................................................................................................................... 5

3. FUNCTIONS AND DETAILS.................................................................................................................... 7

3.1 LCD Screen:........................................................................................................................................ 8

4. MAIN BOARD AND CONNECTIONS...................................................................................................... 9

4.1 Main Board Details:........................................................................................................................... 9

4.2 Backup Battery Connection ............................................................................................................. 10

4.3 Main Power Connection.................................................................................................................. 11

4.4 Detector Connections...................................................................................................................... 11

4.5 PPS Series Detectors Connections................................................................................................... 13

4.5 Relay Outputs .................................................................................................................................. 15

5. FIRST RUN.......................................................................................................................................... 15

5.1 Automatic Test ................................................................................................................................ 16

5.2 LED Test ........................................................................................................................................... 16

6. PROGRAMMING ................................................................................................................................ 16

6.1 Set FAN1 Relay Level: ...................................................................................................................... 16

6.2 Set FAN2 Relay Level: ...................................................................................................................... 17

6.3 Set Alarm Relay Level: ..................................................................................................................... 18

6.4 Set Alarm Activation Type: .............................................................................................................. 18

6.5 Set Gas Type: ................................................................................................................................... 19

6.6 Set Language: .................................................................................................................................. 20

6.7 Scan Detectors:................................................................................................................................ 21

6.8 Show Detector:................................................................................................................................ 21

7. ALARM STATUS.................................................................................................................................. 22

7.1 What to do in case of alarm ............................................................................................................ 22

8. FAULT CODES................................................................................................................................. 23

Declaration ............................................................................................................................................ 24

Warranty Statement.............................................................................................................................. 25

PRS-UM-PPSM-EN-Rev.03-10.04.2020

1.INTRODUCTION

Prosense PPS Control Panel is produced specially for carparking area. Prosense PPS control Panel is

able to provide automatic gas concentration reading for gases CO, NO and LPG that mostly exist on

car parking areas. PPS Control Panel permanently transmits the gas concentration measurement

from detectors to the control unit. Before the gas concentration in the atmosphere reaches the LEL

or toxic PPM level, the control panel is able to shut off a gas valve, cut off power and turn on an

alarm via activating relays.

Prosense PPS Control Panel can have up to 4 zone modules that each can monitor up to 32 detectors.

A fully configured PPS Panel can handle managing 128 detectors. PPS Panel can be configured

depending on detectors used in each project with one, two, three or four zone modules.

Prosense PPS Panel has three relays on each zone module those are two level fan relays (F1 and F2)

and one alarm relay. Fan relays are not alarm relays. They will be activated after 60 seconds once the

defined threshold level exceeded and deacticvated after 240 seconds than the alarm status returned

to normal. The PPS Panel has one power module that can provide power to all zone modules. This

power module has also two relays which are fault and alarm. These relays will be activated if any one

of the zone modules generates fault and or alarm status.

Prosense PPS Control panel can manage up to 128 addressable detectors via RS485 serial

communication protocol. PPS Panel has an 2x8 LCD display to adjust measurement and alarm levels.

This LCD screen and menu keys allow user to set correct properties for each detector like gas

concentrations by gas type, measument type, range and alarm levels.

1.1 Technical Specifications

Power Source

220VAC +/-10%

Power Consumption

27VDC/200mA – 5.4W max. (without connected detectors)

Inputs (Internal)

4 x 32 detectors via RS485 serial input

Relay outputs

Fan1, Fan2, Alarm for each zone

Fault and Alarm for overal status

Contacts rating

3A, 24VDC or 3A 120VAC

Display

Graphic LCD (2x8)

LED indicators

Fan1, Fan2, Alarm

Power/ON, Fault, Alarm LEDs

Backup battery

2 x 12V 7A/h (Optional)

Operating Temp.

0-50C

Humidity

15-85% non condensing

Housing

ABS IP66 (366 X 276 X 186 mm)

Weight

5,5 kg

Main power fuse

Backup battery fuse

Table 1 : Technical specifications

PRS-UM-PPSM-EN-Rev.03-10.04.2020

1.2 Panel Dimensions

Panel dimensions are explained in Diagram 1:

Diagram 1: Dimensions (mm)

2. INSTALLATION

The PPS Control Panel box should never be placed in an explosive atmosphere and should be readily

accessible. It is necessary to drill holes for cable glands either on the top or bottom of the control

unit, depending on which side the electric cables are running in. Before drilling any holes you can

unscrew and remove the electronic parts to avoid accidentally damaging it. PPS Control panel should

not be placed near by high voltage cables or power cable, coaxial cables or transmitters, welding

stations or frequency regulators.

The PPS Control Panel box produced based on IP66 standard specifications. Always use the screw

holes to mount it and do not pierce panel from any other side. Always use cable glands to make cable

entries.

The PPS Control Panel has 4 plastic screws on the front of panel. Use a flat screwdriver to loose them

and remove the cover part on the front. Please take care and remove the connectors on the

electronic card while removing the cover. Fix the panel on the wall via using 4 screw holes after

removing the front cover. Reattached the front cover and tighten 4 plastic screws when wall

mounting completed.

PRS-UM-PPSM-EN-Rev.03-10.04.2020

Diagram 2: Panel cover plastic screw

To prepare cable entries, remove plastic covers from top or bottom of the panel. Then drill the holes

for cable entry and install cable glands to the holes you made it. Make sure you are using an

adequate IP66 rate cable gland to assure the box ingress protection is not compromised. The panel

box is modular and can be used with different assemblies. Prosense recommends having cable

entries from the lower side. Electronic board is located in the front cover of the panel. The power

supply is located at the back of panel box. The power must be connected to this power supply. If the

installation requires the connection to a backup battery, place the battery to lover right side of the

panel inside.

Diagram 3: Panel body

Plastic screws

Backup battery connectors and fuse

Wall mounting hole

Power supply

N L G V-V+

Wall mounting hole

Main power entry and fuse

Space for backup

batteries

Power supply LED

Power supply output

adjustment switch

PRS-UM-PPSM-EN-Rev.03-10.04.2020

3. FUNCTIONS AND DETAILS

The front panel has the following LEDs for each zone as shown in Diagram 4:

Sign

Meaning

Panel is in operation

FAN1

FAN1 relay status

FAN2

FAN2 relay status

ALARM

ALARM status

FAULT

Fault condition in at least one of the zone module

Table 2 : Front panel signs and meanings

There are four buttons near by LCD screen to perform configuration and display the detector details.

Their functions are given in table (The key assignments may vary depending on the menu page):

Key

Function For Configuration

Function For Display Operation

Enter to panel configuration

OK - Select key

Test button

Return back

↑

Go up

Go to next channel

↓

Go down

Go to next channel

Table 3 : Panel buttons and functions

Diagram 4: Front panel signs LCD and LEDs

There is a front plastic cover to protect panel from outer shells, water and dust. To reach to panel

first you need to open plastic cover via pressing both sides of the latches on the front.

PRS-UM-PPSM-EN-Rev.03-10.04.2020

Press to open 

Diagram 5: Front cover

If panel ordered with keys a key needed to open plastic cover. In order to make panel connection,

you need to open the front cover using the key at right bottom side of front panel. The key works

clockwise and vice versa.

Diagram 6: Front cover with key

Diagram 7: Locker

3.1 LCD Screen:

PPS Panel has 2x8 LCD display on each zone module to show detector address, measurement level

and range as well as detector gas type.

Sign sample

Meaning

Measured gas type

Gas level measured by detector

Measurement range (PPM)

D01

Detector address

Table 4 : LCD screen details

If there is no detector connected to channel, LCD screen will show fault status on channel (FLT) and

fault LED will be activated. That channel should be closed (deactivated) via using menu steps.

Locker

PRS-UM-PPSM-EN-Rev.03-10.04.2020

4. MAIN BOARD AND CONNECTIONS

4.1 Main Board Details:

PPS Control panel has one power module and main power connection from power supply to control

panel made on this board. This board provides power to zone modules.

Diagram 8: Control panel main board

As shown in the picture, power module has its own fuse. Power module equipped with two relay

modules as fault and alarm. Fault relay will be activated when any of the detector goes in to fault

status and alarm relay will be activated when any of the zone modules raise the alarm status.

Each zone module works independantly with the detectors connected to them. The connection made

by the V+, V-, A and B ports on zone module. Each zone module has three relays which are Alarm,

Fan 1 and Fan 2.

Connections to Zone modules

Fuse

Main power input

Backup

battery input

Fault relay

output

Alarm relay

output

PRS-UM-PPSM-EN-Rev.03-10.04.2020

Diagram 9: Control panel zone module board

4.2 Backup Battery Connection

To contiue operation in case of main power failure two backup batteries (12V 7Ah) must be serially

connected to the system. Take extra care to use correct poles while connecting the batteries. The

cables or main board can be damaged in case of mixing pins or making short circuits. Backup

batteries must be connected as shown in Diagram 10 below.

Diagram 10: Backup battery connection

Panel battery input

V+

V-

V+

V-

Battery 1/ 12V 7Ah

Battery 2/ 12V 7Ah

V-

V+

V+ A B V-

Detector connections

Alarm FAN2 FAN1

Relay outputs

Inhaltsverzeichnis

Andere Prosense Bedienfeld Handbücher

Prosense

Prosense S-DP32 Bedienungsanleitung

Prosense

Prosense S-DP8 Bedienungsanleitung

Prosense

Prosense DPX Series Bedienungsanleitung

Prosense

Prosense S-DP4 Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten