Protech SI-X208 Bedienungsanleitung

USER

MANUAL

SI-Xx08 M1

SI-X208 / SI-X308/

SI-X408 / SI-X608

Industrial EtherCAT Slave

I/O Modules

SI-X208 / SI-X308 /

SI-X408 / SI-X608

Industrial EtherCAT Slave I/O Module

All trademarks and registered trademarks mentioned herein are the

property of their respective owners.

This manual is copyrighted in May. 2020. You may not reproduce or

transmit in any form or by any means, electronic, or mechanical,

including photocopying and recording.

DISCLAIMER

This user’s manual is meant to assist users in installing and setting up

the system. The information contained in this document is subject to

change without any notice.

CE NOTICE

This is a class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take

adequate measures.

FCC NOTICE

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment

not expressly approve by the party responsible for compliance could

void your authority to operate such equipment.

WARNING: Some internal parts of SI-Xx08 may

have high electrical voltage. We strongly recommend

that only qualified engineers are allowed to service

and disassemble SI-Xx08. If any damages should

occur on SI-Xx08 and are caused by unauthorized

servicing, it will not be covered by the product

warranty.

Contents

Revision History ............................................................................................. ii

1SI-Xx08 Introduction ........................................................................... 1-1

1.1 SI-Xx08 Introduction................................................................... 1-2

1.2 Applications ................................................................................ 1-2

1.3 User Manual Structure ............................................................... 1-3

2Getting Started .................................................................................... 2-1

2.1 System Architecture ................................................................... 2-2

2.2 System Overview ....................................................................... 2-3

2.2.1 Six Views ............................................................................ 2-3

2.2.2 Appearance......................................................................... 2-6

2.2.2.1 Front Panel ................................................................... 2-6

2.2.2.2 Top Panel ..................................................................... 2-9

2.3 Specifications ........................................................................... 2-11

2.3.1 SI-Xx08 System Specifications......................................... 2-11

2.3.2 I/O Specifications .............................................................. 2-12

2.3.2.1 SI-X208 I/O Specifications ......................................... 2-12

2.3.2.2 SI-X308 I/O Specifications ......................................... 2-12

2.3.2.3 SI-X408 I/O Specifications ......................................... 2-13

2.3.2.4 SI-X608 I/O Specifications ......................................... 2-13

2.4 Block Diagram ..........................................................................2-14

2.4.1 SI-X208 Block Diagram .................................................... 2-14

2.4.2 SI-X308 Block Diagram ....................................................2-15

2.4.3 SI-X408 Block Diagram ....................................................2-16

2.4.4 SI-X608 Block Diagram ....................................................2-17

2.5 Quick Start................................................................................ 2-18

Contents

SI-Xx08 SERIES USER MANUAL

Page: ii

2.6 Configuration and Operation ....................................................2-19

2.6.1 SI-X208 ............................................................................. 2-20

2.6.1.1 EEPROM Update .......................................................2-20

2.6.1.2 ESI File Rule .............................................................. 2-26

2.6.1.3 Index Ranges ............................................................. 2-29

2.6.1.4 System Topology ........................................................ 2-29

2.6.2 SI-X308 ............................................................................. 2-30

2.6.2.1 EEPROM Update .......................................................2-30

2.6.2.2 ESI File Rule .............................................................. 2-35

2.6.2.3 Index Ranges ............................................................. 2-38

2.6.2.4 System Topology ........................................................ 2-38

2.6.3 SI-X408 ............................................................................. 2-39

2.6.3.1 EEPROM Update .......................................................2-39

2.6.3.2 ESI File Rule .............................................................. 2-44

2.6.3.3 Index Ranges ............................................................. 2-48

2.6.3.4 System Topology ........................................................ 2-48

2.6.4 SI-X608 ............................................................................. 2-49

2.6.4.1 Scan Device ............................................................... 2-49

2.6.4.2 Import PLC Code........................................................2-53

2.6.4.3 GUI ............................................................................. 2-56

2.6.4.4 PLC Code POU Description.......................................2-59

2.7 Safety Precautions ................................................................... 2-60

3Hardware Configuration ..................................................................... 3-1

3.1 SI-X208 Pin Assignment ............................................................ 3-2

3.2 SI-X308 Pin Assignment ............................................................ 3-3

3.3 SI-X408 Pin Assignment ............................................................ 3-4

Contents

iii

3.4 SI-X608 Pin Assignment ............................................................ 3-5

3.5 I/O Connections ......................................................................... 3-6

3.5.1 Isolated Digital Input Connections ...................................... 3-6

3.5.2 Isolated Digital Output Connections ................................... 3-8

3.5.3 Isolated Analog Input Connections ..................................... 3-9

3.6 Installing DIN-Rail Mount ......................................................... 3-10

3.7Technical Support..................................................................... 3-11

Revision History

SI-Xx08 SERIES USER MANUAL

Page: ii

Revision History

The revision history of SI-Xx08 User Manual is described below:

Version No.

Revision History

Date

Initial Release

2020/05/11

SI-Xx08 SERIES USER MANUAL

Page: 1-1

1 SI-Xx08 Introduction

This chapter provides the introduction for SI-X208,

SI-X308, SI-X408 and SI-608 modules, applications list as

well as the framework of the user manual.

The following topics are included:

•SI-Xx08 Introduction

•Applications

•User Manual Structure

Chapter 1 Introduction

SI-Xx08 SERIES USER MANUAL

Page: 1-2

1.1 SI-Xx08 Introduction

Thank you for purchasing our SI-Xx08 Industrial EtherCAT Slave I/O

Modules which supports EtherCAT protocol. EtherCAT (Ethernet Control

Automation Technology) which is developed by BECKHOFF Automation is

a high-performance Ethernet-based fieldbus industrial network system. This

protocol which is standardized in IEC standard IEC61558 is suitable for

real-time automation applications.

All EtherCAT Slave I/O Modules can be connected by the network topologies

such as star, line, or ring. Our SI-Xx08 I/O modules are installed by daisy

chain connection which has the flexibility in devices installation and reduces

the costs of infrastructure and operations. For the power requirements, the

SI-Xx08 modules are designed for standard industrial unregulated 24 VDC

Power input. However, they accept any power unit that supplies power within

the range of +9 to +48 VDC. All the I/O modules have the isolated input and

output design which protects SI-Xx08 I/O modules against external

interference and environment. The EtherCAT Slave Controller has passed and

has been verified by the conformance test tool. The qualified EtherCAT

Master can connect with SI-Xx08 modules easily and can be applied for

various applications.

1.2 Applications

Factory Automation

Machine Automation

Machine Tooling

Data Acquisition

Chapter 1 Introduction

SI-Xx08 SERIES USER MANUAL

Page: 1-3

1.3 User Manual Structure

Chapter 1 Introduction

This chapter gives the brief introduction of SI-Xx08, applications list as well

as the framework of this user manual.

Chapter 2 Getting Started

This chapter describes the system architecture, system and I/O specifications,

illustrates the physical appearances, block diagrams, quick installation guide

as well as configuration and operation. Read the safety reminders carefully on

how to take care of SI-Xx08 properly.

Chapter 3 Hardware Configuration

This chapter describes the information of pin assignment, wire connection and

DIN-Rail mount installation.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere protech E/A-System Handbücher

protech

protech SI-W109 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

protech SI-X208 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken