Protos Integral Bedienungsanleitung

Protos®Integral

www.protos.at

User Manual

1. Adjustments for perfect comfort of wear and optimal safety

1.1 Adjusting for head size:

1.3 Fasten chin strap:

Push the neck guard towards the inside of the helmet

until it snaps into place (with a slight click). In this positi-

on you can see the right and left adjustment straps (see

circle Fig. 3). Use these to adjust the Protos® Integral

safety helmet to your head size.

Slide the adjustment straps (Fig. 3) to the

inside or outside (to adjust for smaller or larger

head size) and ﬁx them in the desired position.

Please make sure to adjust both sides equally

to ensure that the helmet will sit straight on

your head! The lines on the neck guard holder

serve as orientation (see circle).

Once you have adjusted and set both sides,

push the neck guard back into its initial positi-

on. The helmet should now ﬁt ﬁrmly but not be

too tight. If the helmet does not ﬁt your head

comfortably, readjust the settings.

Push the adaptor button towards

the outer shell. Now you can select

one of the three ride heights by

pushing the button in our out. Here,

too, make sure to make the same

adjustments on both sides!

You make adjustments to se-

lect one of 3 variable ride

heights directly to the left

and right of the neck guard.

If you have a helmet with hearing

protection, it is easiest to get at the

adjustment straps if you put the ear

protectors in the stand-by position

(see Fig. 14).

TIP!

Neck Guard

Open the chin

strap as shown in

the illustration.

Neck Guard Holder

Adjustment Straps

Back snap fastener

Front snap fasteners

TIP!

Push the “back snap faste-

ner” into the socket in the

back under the neck guard

on the inside of the helmet

by pushing down hard.

Now pull the chin strap

through the guides on both

sides of the back part of the

neck guard (to do so, it is

best to push the neck guard

outwards again).

There are two more fasteners at

the front of the chin strap (Fig.

6). Snap both of these into the

sockets on both sides (circles).

Lock them into place by pulling

slightly, so that they point to the

inside of the helmet (Fig. 11).

Once you have made ﬁnal

adjustments to your chin

strap, the excess part of the

strap can be cut off and the

cut edge can then be melted

using a lighter.

Make sure the tension

of the chin strap is the

same on both sides!

14 15

Put the ear protectors into the

active position so that they ﬁt

closely over your ears.

1.4 Adjusting the ear protectors:

To adjust for optimal height, push the

ear protectors up or down until they ﬁt

comfortably over your ears.

To put the ear protectors back into the

stand-by position, pull them outward

a little and push them back with two

ﬁngers (also see Fig. 14).

Stand-by position Active position

The pressure, with which the ear pieces ﬁt

over the ears, can be adjusted. To do so,

remove the ear protectors (in the active

position, Fig. 15). «Press» on the red tab

to pull the ear protectors from the shell of

the helmet.

Now turn the pressure regu-

lator with a 1- or 2-cent coin

(10 or 50 centime CHF) to

increase (+) or decrease (-)

the pressure.

Take the ear protection incl. bracket and

slide it into the corresponding clasp.

Attention! The arrows on the ear pie-

ces should point to the front of the helmet

(Fig. 15 and 16).

Remove the crown and

neck pad from the Velcro

fastening by pulling on it

and exchange with repla-

cement pads.

2. How to exchange parts:

If parts of your Protos® Integral safety helmet become worn or damaged, or if they must be cleaned, they can be

easily exchanged.

2.1 Changing the brow, crown and neck pad:

Remove the brow pad held by

plastic clips from the brow pad

holder and clip in the new and/

or dry brow pad starting from the

right or left.

Open the visor, which is

attached to round mounts

on the inside.

Pull strongly to remove the

visor from the mounts.

2.3 Changing the ear piece pads:

First, remove the ear

protectors from the helmet

shell (also see Fig. 17)

Firmly hold the ear piece in your hand

and use your index and middle ﬁnger

to hook under the pad from the side.

The pad can be removed by lightly

pulling on it.

Now place the new pad on the ear

piece and press down evenly.

Protos GmbH

Herrschaftswiesen 11

6842 Koblach - Austria

ofﬁ[email protected]

www.protos.at

Andere Protos Motorradzubehör Handbücher

Protos

Protos Integral IN Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

3M Speedglas 9100 MP Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

Sperian

Sperian Optrel p420 Bedienungsanleitung