●MuteFunction1) The PEC-2 mute circuit is located immediately before OUT-1 and OUT-2. The MUTE switch can function independently, without
being affected by the recalled program.
2) The MUTE LED flashes while the MUTE switch is ON (output is muted).
3) Two mute disengage modes are provided: Manual, in which mute is manually disengaged via the MUTE switch, and Automatic,
in which mute will also be disengaged whenever a program switch is pressed. The Automatic mode can facilitate faster operation
in many situations, and minimizes no-sound “accidents” caused by forgetting to disengage the mute function. (See page 10 for
more details).
●MIDIFunctions1) M D N and OUT/THRU connectors are provided to allow M D communication with external equipment. The PEC-2 can also be
used as a M D pedal.
2) The M D receive and transmit channels can be set as required.
3) M D control change numbers can be assigned to the PGM1/L1 ~ PGM7/L8, MODE, and MUTE switches as required, allowing the
PEC-2 to be used in a wide range of M D -based systems.
4) The PEC-2 program numbers correspond directly to the M D program change numbers transmitted and received. For example,
M D program change number “015” will be transmitted when PEC-2 program number “015” is recalled. Conversely, PEC-2 program
number “115” will be recalled when M D program change number “115” is received. Since the PEC-2 only handles banks 00 ~ 11
and programs 1 ~ 7 some M D program change numbers are not transmitted or received. Also note that the M D program change
numbers transmitted and received by the PEC-2 cannot be edited. (Refer to page 11 for details on the PEC-2 M D settings).
5) When two PEC-2 units are being used in the link mode, the M D N and OUT/THRU connectors of both units can be used. When
one PEC-2 unit is being used with a second PEC-2 in the remote mode, only the M D N and OUT/THRU connectors of the MASTER
unit are available for use. The SLAVE unit M D connectors are not operational.
●LinkFunctions1) L NK Mode
• Two PEC-2 units can be linked to function as an effect controller that will handle up to 16 loops. With linked PEC-2 units, when
the PGM mode is selected recalling a program on either unit will recall the same program on the second unit as well. The loop
switch status for each PEC-2 is stored in the corresponding PEC-2 unit. n the D RECT mode the loops on either unit can be
directly turned on or off as required.
2) REMOTE Mode
• With this function you could place one PEC-2 unit on stage and another in the wings and use one or the other as a “remote con-
trol unit”. One unit is designated as the “master” and the other as the “slave”, and the settings memorized in the master unit are
recalled.
• The PEC-2 designated as the slave unit can also be used as a backup. Copy the data from the master unit to slave unit before-
hand, and you’ll be prepared for a quick changeover in case a malfunction occurs.
Refer to page 12 for setting details.
●MemoryFunctions1) The PEC-2 has 84 independent memory locations (7 programs x 12 banks).
2) A memory protect function is provided to prevent accidental changes to the memory contents. Refer to page ?? for more
details.
●Mechanics1) A new type of footswitch provides solid tactile feedback.
These switches won’t operate if you simply rest your foot lightly on them, minimizing the possibility of accidental switching.
2) Like the PEC-1, the PEC-2 features a sloping panel designed to make switching comfortable and easy. A low profile also con-
tributes to smooth, easy operation.
3) The depth of the PEC-2 has been reduced in comparison to the PEC-1. The unit’s compact dimensions mean it will fit comfortably
in most pedal board setups. All of this has been achieved without reducing the switch spacing so operability is not compromised.
4) Rubber feet are provided that can be attached to the bottom of the unit as required. The feet can be omitted so that the bottom of
the unit is flat and can easily be attached to a pedal board using hook-and-loop tape. An optional pedal board mount kit is available
that allows the PEC-2 to be securely attached to a pedal board using four wood screws.
5) The buffered input (Bu- N) and non-buffered input ( N) jacks are identified by red washers, while the OUT-1 and OUT-2 jacks are
identified by blue washers that can be easily seen in low light.
●Othersn live situations most bassists will use a D. . box for direct connection to the sound system (perhaps in addition to a bass amp on
stage). Normally the bassist cannot turn the direct line on and off, and must rely on the sound system operator to mute the bass
channel for setup or tuning. This is not only inconvenient, but also occasionally results in the bass sound being heard via the
sound system when it shouldn’t be. The PEC-2 can be connected and configured to eliminate this problem – see System Example
6 on page 15 for details.
8
