ProVisual PTZ-9300 Bedienungsanleitung
INSTRUCTION MANUAL
Mini Sp
PTZ-9300
eed Dome Camera
DOME 4.5" 100X ZOOM
DAY & N IG HT
★
ON SCREEN
DISPLAY
123
CONTINUOUS
360 360 /sec
SPEED
0.05 /sec
LOW SPEED
PRESET 128
1
2
128
SWING 8 GROUP 8
1
2
3
PATTERN 4 VECTOR
MOTION
PRIVACY
ZONE
ALARM 4 IN
CAUTl0N
CAUTl0N：
TO REDUCE THE RISK OF ELECTRICAL SHOCK,DO NOT OPEN COVERS.
N0 USER SERVICEABLE PARTS INSlDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
WARNING：
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK HAZARD DO NOT EXPOSE
THIS CAMERATO RAIN OR MOISTURE.
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamatlon point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
RISK OF ELECTRIC
SHOCK DO NOT OPEN
1
Spee d Dom e Cam era Instruction Manual
NOTICE
Read Instructions
Read all of the safety and operating instructions before using the product.
Retain Instructions
Save these instructions for future reference.
Attachments∕Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they may
cause hazards,damage product and void warranty.
Water and Moisture
Do not use this product near water or moisture.
Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only
with a mounting device recommended by the manufacturer, or sold with the product. To insure proper
mounting, follow the manufacturer’s instructions and use only mounting accessories recommended by
manufacturer.
Power source
This product should be operated only from the type of power source indicated on the marking label.
Important Safeguard
1.
2.
3.
4.
5.
Precautions
Operating
Handling
Installation and Storage
Before using, make sure power supply and others are properly connected.
While operating, if any abnormal condition or malfunction is observed, stop using the camera
imme diately and then contact your local dealer.
Do not disassemble or tamper with parts inside the camera.
Do not drop or subject the camera to shock and vibration as this can damage camera.
Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
Do not install the camera in areas of extreme temperature, which exceed the allowable range.
Avoid installing in humid or dusty places.
Avoid installing in places where radiation is present.
Avoid installing in places where there are strong magnetic fields and electric signals.
Avoid installing in places where the camera would be subject to strong vibrations.
Never expose the camera to rain and water.
6.
2
Spee d Dom e Cam era Instruction Manual
3
Spee d Dom e Cam era Instruction Manual
CONTENTS
1
4
6
Introduction
Features
Pr od uct ＆Accessor i es
2
7
9
Installation
DIP Switch Setup
Cabling
3
11
11
12
12
13
13
14
15
16
17
Operation
Checking Before Operation
Preset and Pattern Function Pre-Check
Start OSD Menu
Reserved Preset
Preset
Swing
Pattern
Group
Other Functions
OSD Display of Main Screen
5
Specifications
Dimension
32
33
4
18
18
19
20
21
23
25
27
28
29
31
How to use 0SD Menu
General Rules of Menu Operation
Main Menu
Display Menu for Main Screen
Privacy Zone Mask Setup
Camera Module Setup
Motion Setup
Preset Setup
Swing Setup
Pattern Setup
Group Setup
System Initialize
4
Spee d Dom e Cam era Instruction Manual
DAY & NIGHT
★
100X ZOOM
CONTINUOUS
360 360 /sec
SPEED
0.05 /sec
LOW SPEED
VECTOR
MOTION
INTRODUCTION
Features
Powerful Pan/Tilt Functions
Preset, Pattern, Swing, Group, Privacy Mask and More...
PTZ(Pan/Tilt/Zoom)Control
CCD Sensor :1/4"Interline Transfer CCD
Zoom Magnification : x 10 Optical Zoom, x 10 Digital Zoom(Max x 100 Zoom)
Day & Night Function
Various Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus.
Independent＆Simultaneous Camera Characteristic Setup in Preset operation
Max. 360 /sec high speed Pan/Tilt Motion
Using Vector Drive Technology, Pan/Tilt motions are accomphshed in a shortest path. As a resuIt,
time to target view is reduced dramatically and the video on the monitor is very natural to watch.
For jog operati on using a cont ro ller, since ultra slow speed 0.05 ／sec can be reached , it is very easy
to locate camer a to desired target view. Additionally it is easy to move camera to a desired position
with zoom-proportional pan/tilt movement.
MAX. 127 Presets are assignable and characteristics of each preset can be set up independently,
such as White Balance, Auto Exposure, Label and so on.
Max. 8 set of Swing action can be stored. This enables to move camera repetitively between two
preset positions with designated speed.
Max .4 of Patterns can be recorded and played back. This enables to move camera to follow any
trajectory operated by joystick as closely as possible.
Max- 8 set of Group action can be stored. This enables to move camera repetitively with combination of
Preset or Pattern or Swing. A Group is composed of max. 20 entities of Preset/Pattern/Swings.
Privacy Masks are assignable, not to intrude on other's privacy. (4 Privacy Zones)
With RS-485 communication, max. 255 of cameras can be controlled at the same time.
Pelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.
1
Camera Specifications
5
Spee d Dom e Cam era Instruction Manual
AL ARM 41N
INTRODUCTION
OSD (On Screen Display) Menu
I/O Functions
Reserved Presets for Special Purpose
OSD menu is provided to display the status of camera and to configuie the functions interactively.
The information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can be displayed on
screen.
To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo
coupler.
The signal range of sensor input is from AC 12 to 32 OR DC12 to 50 volts to adopt various applications.
If an external sensor is activated, camera can be set to move to the corresponding Preset position
Most camera characteristics can be set up easily and directly with reserved preset, not entering
into OSD menu. For more information, refer to “Reserved Preset” in this manual.
1
(Not Avalible)
6
Spee d Dom e Cam era Instruction Manual
Product & Accessories
Speed Dome
Mounting Base
Screws x 3
Mounting Base
Screws x 3
Screws x 3
Thread Connector
Speed Dome
Speed Dome
Groove
INTRODUCTION 1
Pendant Bracket
Wall Mount Bracket
Ceiling Bracket
Options
Assembly
7
Spee d Dom e Cam era Instruction Manual
PIN
FUNC.
ON
OFF
INSTALLATION
Camera ID Setup
8
128
0ff
7
64
0ff
6
32
0ff
5
16
0ff
5
8
0ff
3
4
0ff
2
2
0ff
1
1
0ff
Pin
ID Value
0ff0ff0ff0ff0ff0ff0ff0ff
e x) ID=5
ex) ID=10
Before you install the camera, you should set the DIP switches to configure the camera ID, communication
protocol.
ID number of camera is set using binary number. The example is
shown bellow.
The range of ID is 1~128. Factory
default of Camera ID is 1.
Donot
use
0
as
camer
r
a
ID.
If you want to control a cartain camera, you must match the camera
ID with Cam ID se tting of DVR or Controller.
12345678
ON
ON
PROTOCOL N/P
Refer to
the Manual
PAL
NTSC
12 12345678
PIN
FUNC.
ON
OFF
A0 A1 A2 A3 A4 A5 A6 A7
0
12 4 1286432168
00000 0
ADDRESS (ID)
ON
OPTIONS
ON
Communication
Prot ocol Camera ID
2
0
1234 12345678
DIP Switch Setup
34
INSTALLATION
ON
Communication Protocol Setup
Select the appropriate Protocol with DIP switch combination.
Switch State
P0 P1 Protocol
(Pin 1) (Pin 2)
OFF
ON
OFF
ON
OFF
OFF
ON
ON
PELCO-D, 2400 bps
PELCO-D, 9600 bps
PELCO-P, 4800 bps
PELCO-P, 9600 bps
ON
1234
If you want to control using DVR or P/T controller, their protocol must
be identical to camera. Otherwise, you can not control the camera.
If you changed camera protocol by changing DIP S/W, the change
will be effective after you reboot the camera.
Factory default of protocol is “Pelco-D, 2400 bps”
Since Pin 3～Pin 4 is only for supplier, DO NOT CHANGE THESE
ORIGINAL STATE. If you change one of these, proper operation can
not be achieved.
Pin 3 PAL / NTSC system selection of Camera. DO NOT
CHANGE THIS PIN.
8
Spee d Dom e Cam era Instruction Manual
2
ON ON
1234
9
Spee d Dom e Cam era Instruction Manual
INSTALLATION
Roated Power
DC 12V
Input Voltage Range
DC 12V~50 V
Current Consumption
0.8A
Please, check the voltage and current capacity of rated power carefully.
Rated power is indicated in the back of main unit.
Power Connection
RS-485 Communication
For PTZ control, connect this line to keyboard and DVR.
To control multiple cameras at the same time,
RS-485 communication lines of them is connected in parallel as shown below.
2
Power Speed Dome
Cabling
BNC
Moinitor
Controller/DVR
Cabling Terminal Block
Keyboard Controller/DVR
RS-485
#1 #2 #N
RS-485( - )
RS-485( + )
Inhaltsverzeichnis
Andere ProVisual Sicherheitskamera Handbücher
ProVisual
ProVisual ptz-9700 Bedienungsanleitung
ProVisual
ProVisual PTZ-9636IR Bedienungsanleitung
ProVisual
ProVisual CB-2085IR-WDR Bedienungsanleitung
ProVisual
ProVisual PTZ-9610-A Bedienungsanleitung
ProVisual
ProVisual CDVN2002-F36 Bedienungsanleitung
ProVisual
ProVisual PTZN-3000-X20 Bedienungsanleitung
ProVisual
ProVisual PTZ2007-X18 Bedienungsanleitung
ProVisual
ProVisual CDV-2085IR-WDR Bedienungsanleitung
ProVisual
ProVisual Box camera Bedienungsanleitung
