Pulsar RUPS824P Bedienungsanleitung

RUPS824P

v.1.0

RUPS 27,6V/8x1A/PTC

RACK mounted buffer power supply.

Edition: 2 from 30.03.2017

Supercedes the edition: 1 from 16.08.2016

www.pulsar.pl RUPS824P RACK POWER

Features:

DC 27,6V/8x1A uninterruptible power supply

8 outputs independently protected with 1A

polymer fuses

wide range of mains supply AC: 176÷264V AC

high efficiency 85%

built-in power factor correction system (PFC)

battery charging and maintenance control

excessive discharging (UVP) protection

battery output protection against short circuit and

reverse connection

battery charge current: 1A

(batteries 2×7Ah / 2x17Ah / 2x28Ah)

control of voltage presence at the AUX1 ÷ AUX8

outputs

acoustic indication of failure

LED optical indication: AC, DC, TEMP, LoB, ALARM,

AUX1 ÷ AUX8

the ALARM technical output of collective failure –relay

type, activated by:

230V AC power loss

low voltage of the PSU (<23V)

activation of the output fuse

too high temperature of the PSU (>70°C)

the PSU failure

protections:

SCP short-circuit protection

OVP overvoltage protection

overvoltage protection

overload protection OLP

forced cooling (fan)

warranty –2 year from the production date

Sample application of the RACK power supply unit.

www.pulsar.pl RUPS824P RACK POWER

CONTENTS:

1. Technical description.

1.1. General description

1.2. Block diagram

1.3. Description of PSU components and connectors

1.4. Specifications

2. Installation.

2.1. Requirements

2.2. Installation procedure

3. Operating status indication.

3.1. LED indication

3.2. Technical output

3.3. Acoustic indication

4. Operation and use.

4.1. Overload or short circuit of the PSU output

4.2. Battery-assisted operation

4.3. Maintenance

1. Technical description.

1.1. General description.

The buffer power supply RUPS824P is used for uninterrupted supply of devices requiring stabilized voltage

of 24V DC (+/- 15%). The PSU supplies voltage of U=27,6V DC and total current capacity of:

Output current 8A + 1A battery charge.

Total device current + battery: 9A max.

In case of power decay, a battery back-up is activated immediately. The PSU is fitted with 8 outputs

protected independently with polymer fuses PTC 1A. The power supply is fitted with the ALARM output of collective

failure. In case of failure, relay contacts are switched automatically, which is accompanied by acoustic and optical

indication (the corresponding led goes on). The power supply construction is based on the switch mode PSU with

high energy efficiency and is located in an enclosure adapted for mounting in standard RACK 19” cabinets.

1.2. Block diagram.

Fig.1. The block diagram of the PSU.

1.3. Description of PSU components and connectors.

Table 1. Elements the front power of the power supply unit.

Element no.

[Fig. 2]

Description

AC OK –green LED, indicating the presence of 230V voltage

DC OK –green LED, indicating the presence of DC voltage

TEMP –red LED, indicating too high temperature of the power supply (>70°C)

LoB –red LED, indicating too low battery voltage (<23V)

LED ALARM –red LED failure indication

www.pulsar.pl RUPS824P RACK POWER

Green LED AUX1 ÷ AUX8 –voltage indication at the AUX outputs

AUX1 ÷ AUX8 –independently protected outputs

BAT –battery output

ALARM –technical output of collective failure –relay

BUZZER, micro switch, turning ON / OFF of acoustic indication

switch in the top position, indication ON

switch in the down position, indication OFF

230V AC INPUT, power socket 230V AC, power cable 1,5m included

FMAINS,fuse in the supply circuit 230V AC, T 6,3A/250V

Fig. 2. The front power of the power supply unit.

Fig.3. The view of the PSU.

www.pulsar.pl RUPS824P RACK POWER

1.4. Specifications.

- electrical parameters (tab.2)

- mechanical parameters (tab.3)

- operation safety (tab.4)

- operating parameters (tab.5)

Electrical parameters (tab. 2).

Mains supply

176÷264V AC

Current up to

1,1A@230V AC max.

Supply power

248W max.

Efficiency

85%

Power factor PF

>0,95 @230V AC

Output voltage

22V ÷ 27,6V DC –buffer operation

19V ÷ 27,6V DC –battery-assisted operation

Output current

8 x 1A + 1A battery charge

Ripple

150 mV p-p max.

Battery charge current

(batteries 2×7Ah / 2x17Ah / 2x28Ah, connect

batteries in series)

1A max. (+/-5%)

Short-circuit protection SCP

8 x PTC 1A, polymer fuse

Overload protection OLP

105% ÷ 150% of the PSU power, automatic return

or: 8 x PTC 1A

Current consumption by PSU systems

0,24A

Overvoltage protection OVP

>32V (activation requires disconnecting the load or supply

for about 20s.)

Battery circuit protection SCP and reverse

polarity connection

glass fuse

Surge protection

varistors

Excessive discharge protection UVP

U<19V (+/-5%) –disconnect of connection battery

Optical indication of operation:

LED: AC, DC, TEMP, LoB, ALARM, AUX1÷AUX8

Acoustic operation indication:

Piezoelectric indicator ~75dB/0,3m

The ALARM technical output of collective failure

Relay type: 1A@ 30VDC/50VAC

FMAINS fuse in the power supply circuit 230V

T 6,3A

Mechanical parameters (tab. 3).

Enclosure dimensions

W=19”, H=2U; 482 x 88 x 223 mm (WxHxD)

Fixation

four-point butt mounting to RACK profiles –the set include 4 M6 screws + cage nuts

Net weight

5,8kg / 6,2kg

Enclosure

Steel plate RAL 9005, black

Connectors

230V AC input: the IEC C14 socket with a fuse, power cable 1,5m

(included)

Outputs: ALARM, AUX1÷AUX8: Φ0,5-2,1 (AWG 24-12) 0,5-1,5mm2

Battery output BAT: 6,3F-2,5

Notes

Forced cooling (fan).

Operation safety (tab.4).

Protection class PN-EN 60950-1:2007

I (first)

Protection grade PN-EN 60529: 2002 (U)

IP20

Electrical strength of insulation:

- between input and output circuits of the PSU (I/P-O/P)

- between input circuit and PE protection circuit (I/P-FG)

- between output circuit and PE protection circuit (O/P-FG)

3000 V/AC min.

1500 V/AC min.

500 V/AC min.

Insulation resistance:

- between input circuit and output or protection circuit

100 MΩ, 500V/DC

Operating parameters (tab.5).

Environmental class

Operating temperature

-10ºC...+45ºC

Storage temperature

-20ºC...+60ºC

Relative humidity

20%...90%, without condensation

Vibrations during operation

unacceptable

Impulse waves during operation

unacceptable

Direct insulation

unacceptable

Vibrations and impulse waves during transport

According to PN-83/T-42106

www.pulsar.pl RUPS824P RACK POWER

2. Installation.

2.1. Requirements.

The PSU RACK shall be mounted by a qualified installer with appropriate permissions and qualifications for

230V/AC installations and low-voltage installations (required and necessary for a given country). The device shall

be mounted in confined spaces, according to the environment class II, with normal air humidity (RH=90% max.

without condensation) and the temperature from -10°C do +45°C.

During normal operation the total current consumption of the cameras cannot exceed

I=8A. Maximum battery charging current is: 1A.

Total device current + battery: 9A max.

As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an

appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be

informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The

electrical system shall follow valid standards and regulations.

2.2. Installation procedure.

1. Before installation, cut off the voltage in the 230V power-supply circuit.

2. Mount the power supply in a RACK 19" cabinet as shown below:

- Mount M6 cage nuts

- Secure the enclosure with 4xM6 screws

3. Connect the receivers’ cables to the terminals AUX1...AUX8.

4. If needed, the following technical connections can be made:

- ALARM –technical output of collective failure

5. Connect the battery in series to the +BAT- terminals:

- battery output (+): terminal BAT+

- battery output (-): terminal BAT-

6. Connect the ~230V AC power cord with the IEC C13 plug (included) to the 230V AC power supply and turn on

the power (~230V).

7. Check the PSU operation indicator.

3. Operating status indication.

3.1. LED indication.

The PSU has 13 LED lights at the front panel:

GREEN LED:

on –the PSU is supplied with 230V AC

off –no 230V AC supply

GREEN LED:

on –DC voltage at the output of the switch mode PSU

www.pulsar.pl RUPS824P RACK POWER

off –no DC voltage at the output of the switch mode PSU

RED LED:

on –failure

off –no failure

RED LED:

ON –too high temperature of the switch mode power supply

(>70°C)

OFF –standard temperature of the switch mode power supply

RED LED:

on –battery voltage <23V

off –battery voltage >23V

GREEN LED:

on –DC voltage in the AUX1…AUX8 output

off –no DC voltage in the AUX1…AUX8 output

3.2. Technical output.

The power supply is fitted with the ALARM output of collective failure (relay type). A collective failure can

be triggered by the following events:

- 230V AC mains power failure

- Activation of the polymer fuse PTC

- Failure of the switch mode power supply

- Too high temperature of the switch mode power supply (>70°C)

- Low battery voltage (<23V)

Fig. 4. Electrical diagram of the ALARM collective output of failure.

CAUTION! In Fig.4 the set of contacts shows a potential-free status of the relay, which

corresponds to power supply failure.

3.3. Acoustic indication.

A collective failure is indicated by the piezoelectric indicator, 1 beep every second. The acoustic indication

can be turned off by changing the ON / OFF position of the switch .

switch in the up position, indication ON

switch in the down position, indication OFF

www.pulsar.pl RUPS824P RACK POWER

4. Operation and use.

4.1. Overload or short circuit of the PSU output.

The AUX1 ÷ AUX8 power supply outputs are protected against short-circuit with polymer fuses PTC. If a

fuse-assisted protection has been chosen, replace the fuse (of the same parameters) in case of a failure.

4.2. Battery-assisted operation.

In case of a main power outage, the device is immediately switched into a battery-assisted operation.

The PSU is equipped with the discharged battery disconnection system. During

the battery-assisted operation, reducing voltage below 19V at the battery terminals will

cause battery disconnection.

4.3. Maintenance.

Any and all maintenance operations may be performed following the disconnection of the PSU from the

power supply network. The PSU does not require performing any specific maintenance measures. In case of fuse

replacement, use a replacement of the same parameters.

WEEE LABEL

Waste electrical and electronic equipment must not be disposed of with normal household

waste. According to the European Union WEEE Directive, waste electrical and electronic

equipment should be disposed of separately from normal household waste.

Pulsar

Siedlec 150, 32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

E-mail: biuro@pulsar.pl, sales@pulsar.pl

http:// www.pulsar.pl, www.zasilacze.pl

Inhaltsverzeichnis

Andere Pulsar Stromversorgung Handbücher

Pulsar

Pulsar PSBS 10A12C Bedienungsanleitung

Pulsar

Pulsar PSBSH 1012B Bedienungsanleitung

Pulsar

Pulsar AWZ 224 Bedienungsanleitung

Pulsar

Pulsar PSDC161216T Bedienungsanleitung

Pulsar

Pulsar PSBS 1024B Bedienungsanleitung

Pulsar

Pulsar GREEN POWER plus HADOC 3012C Bedienungsanleitung

Pulsar

Pulsar PSB-12V20A Bedienungsanleitung

Pulsar

Pulsar PSBEN 3024C Bedienungsanleitung

Pulsar

Pulsar PSDC 08128 Bedienungsanleitung

Pulsar

Pulsar AWO003PU Bedienungsanleitung

Pulsar

Pulsar PSC12010 Bedienungsanleitung

Pulsar

Pulsar PSP48005 Bedienungsanleitung

Pulsar

Pulsar POE1648 Bedienungsanleitung

Pulsar

Pulsar PSCC20700 Bedienungsanleitung

Pulsar

Pulsar PSBOC1554828 Bedienungsanleitung

Pulsar

Pulsar HPSB 7012C Bedienungsanleitung

Pulsar

Pulsar AWO305 Bedienungsanleitung

Pulsar

Pulsar PSCV3512 Bedienungsanleitung

Pulsar

Pulsar PSUPS20A12E Bedienungsanleitung

Pulsar

Pulsar Zenith 140 Bedienungsanleitung

Pulsar

Pulsar PSDC 161214 Bedienungsanleitung

Pulsar

Pulsar POE0848 Bedienungsanleitung

Pulsar

Pulsar PSBEN 5012D Bedienungsanleitung

Pulsar

Pulsar GREEN POWER plus HPSBOC 20A12E Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung

Elmdene

Elmdene G1380xN-y-s Series Bedienungsanleitung